Search Documents

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By Richard W. Graeme, James J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona project, located in Hualgayoc, Cajamarca Department, Peru, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, project development occurred against the backdrop of a presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as an unprecedented demand for engineering and technical skills. Project “Lessons Learned” are discussed in the context of an evolving strategy. The Cerro Corona project forms part of a porphyry copper-gold deposit situated within the Hualgayoc Mining District in northern Peru. It is located in the highest part of the Western Cordillera of the Andes, close to the headwaters of the Atlantic Continental Basin. It lies approximately 90 km (56 miles) by road north of the Department of Cajamarca’s capital city and near the village of Hualgayoc. Access to the Cerro Corona project from Cajamarca is by two roads, one from Cajamarca to the Yanacocha Mine 45 km (28 miles), and then from Yanacocha to the village of Hualgayoc and the town of Bambamarca 45 km (28 miles).

Jan 1, 2007

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat&apos; and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states&apos; to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper&apos;. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243&apos;, 2188&apos; and 2188&apos; respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

This paper summarises the development t,) date for the Hidden Valley Gold (HVG) Project. It starts with the original exploration work, covers the detailed feasibility study activities and concludes with the current phase of extra exploration drilling. A brief technical summary has been made from the various mining, process and environmental studies that were undertaken as part of the project approval process. A discussion of the influential non-technical factors is included, as well as a view of the future prospects for an operating mine. The project was always seen as marginal, given the low grades, small resource and short mine life. However the capital and operating costs were lowered with aggressive design and it was regarded an acceptable development by CRA. The opportunity was taken to review the project when delays in start-up were encountered. An updated financial evaluation showed a subeconomic resource in 1990 terms and this resulted in a new exploration phase to identify a larger deposit.

Jan 1, 1991

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By Jesus Frisancho Cabrera

El aumento de precios por la demanda de acero en China, consolida a dicho país en un importador neto de molibdeno desde 2010. En ese contexto, el presente texto señala la influencia del molibdeno en la exploración del pórfido de cobre -en tanto los bajos niveles de las exportaciones de crudo de China continúan obligando a los productores de acero de Corea y Japón de molibdeno utlizarlo como fuente de Occidente.

Sep 12, 2011

A wide range of materials are used in hydraulic backfilling operations and the pipeline flow behaviour of these mixtures varies considerably. It is shown that despite the large differences in constituent materials and flow behaviour, a common approach can be applied to analysing the flow of all hydraulic backfills. This is extended to include a rational design approach for backfill distribution systems. The use and limitations of pipe loop tests as a design aid is discussed. Backfill quality control is identified as a key area where improvement needs to be made to enhance the reliability of backfill system operation.

Jan 1, 2001

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By W. F. Scott, K. L. Somerville

"This paper outlines the development and inplementation of functional training at the Thompson Mine of Inco Metals Company, Manitoba Division. This training is an extension of similar methods implemented throughout the company to meet safety and health and productivity objectives. It consists of the orientation to the mine, induction in the basic mining skills, and specific training in drilling and other skills in the mine. Initial results indicated a positive effect on the safety performance and proficiency of the mine workforce.IntroductionThe primary mining method at the Thompson Mine is mechanized cut and fill, with secondary recovery of pillars by undercut and fill . These methods require a workforce of about 900 hourly operating employees to obtain capacity production of 6500 tons of ore per day.Historically, turnover of mine employees has been high and large numbers of new recruits are introduced to the mine every year. These men are recruited primarily in Manitoba, but also from distant areas of Canada; most of the se people have no previous mining experience.Training has always been an important component of mine operations. Mine supervisors and experienced miners have committed an appreciable amount of time and effort to training these new recruits. As well, training efforts have been directed toward upgrading the skills of experienced workers.Recently, a growing awareness of the significance of this training effort and its impact on accident frequency, productivity, turnover and other important parameters of the mine operation has led to a review of training methods. The training program described in this paper has resulted from this review."

Jan 1, 1981

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920&apos;s a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

By John Fritz

MEMBERS of the American engineering societies who were in London and Paris during the last days of. June and early July were present at many interesting gatherings. The official delegates of the Founder societies were the specially honored guests of the foreign engineering societies, but other American engineers took part in the meetings. The members of the delegation were: Arthur S. Dwight, Charles F. Rand, William Kelly, representing A. I. M. E.; Ambrose Swasey (general chairman of deputation), Ira N. Hollis, Jesse M. Smith, representing A. S. M. E.; F. B. Jewett, A. E. Kennelly, G. O. Squier, representing A. I. E. E.; Charles T. Main, Robert A. Cummings, John R. Freeman, D. C. Henny, representing A. S. C. E.

Jan 1, 1921

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.