Search Documents

By James T. Kemp

Some interesting and, to American eyes, rather unusual processes for refining impure aluminum derived from scraps were found by American and British investigators who went into Germany in 1945 for the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. What was found was recorded in a series of reports (see page ), many of which have been released for general reading. This paper gathers under one title and summarizes the German work in refining light metal scrap. Reference must be made to the original reports for greater detail. Basically, the occasion and stimulus for the German developments in treating light metal scrap were hard necessity. Germany needed the metal for a rapacious war industry. Adequate supplies of new aluminum from reduction works were not assured. Great quantities of airplane and other light metal war scraps were forecast. It was evident that the scrap metal would have to be reabsorbed by the producing industry and would have to be kept of good quality. The normal current production of manufacturing scrap was being and could be consumed as generated. It offered no technical problem. The mixed scraps, especially those arising from crashed and decommissioned airplanes, however, presented problems of another kind. Airplane Scrap The recovery of usable aluminum alloy from the mixed assemblies that made up the piles of airplane scrap was attacked in different ways by different groups and with differing degrees of success. Three procedures actually were used on a commercial scale, one was in pilot-plant stage and another had come to a halt in the laboratory a year before Germany collapsed. Four of these five processes actually involved "refining"; that is, some measure of purification of the metal after melting. Sorting and Separation on a Sloping Hearth The simplest procedure for utilizing airplane scrap involved no refining in the strict sense of the word. This was the practice adopted by two representative plants visited by the author, the Leipziger Leichtmetalle Werke, Rackwitz, Saxony, and the Vereinigte Leichtmetalle Werke, Hanover. These firms did essentially the same thing that was done in England but not with equal success, to judge by their shorter experience, the smaller tonnage handled and by the number and quality of alloys produced. The two German firms named rough-sorted scraps by their easily recognizable alloys, essentially by part and shape. They used hand labor to chop and hack and tear apart. The easily separated heavy metal and nonmetallic scraps were discarded as they were found. Steel and the higher-melting-point metal parts riveted to aluminum or built into

Jan 1, 1947

By W. M. Peirce

COMMENCING in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole to point out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things. Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944

About 90 per cent of the pre-mining BIF-hosted iron ore resource of the Hamersley Province of Western Australia is of the Phanerozoic supergene martite-goethite type. The remaining ten per cent formed as supergene deposits at ~2000 ¦ 200 Ma, and were later modified by burial to form the Proterozoic martite-microplaty hematite ores. The supergene-metamorphic segment of this general unified model has been challenged by three recently published hypogene-based genetic models for the hematite ores, all requiring meteoric oxidation to produce the ore. The most recent and detailed, by Taylor et al (2001), is based on data from the small Southern Batter and North deposits of the Mount Tom Price mine. The authors proposed that during Stage 1 æoverpressured bicarbonate-saturated basin brines from the dolomite aquifer of the Wittenoom FormationÆ at 150 - 250¦C, dissolved free silica from BIF to produce a stratigraphically thinned, magnetite-carbonate-silicate-apatite rock. In Stage 2, meteoric oxidation of siderite to secondary microplaty hematite + ankerite, and magnetite to martite, at unspecified elevated temperatures and pressures, was followed by carbonate leaching (Stage 3). Finally, during Stage 4, weathering with removal of apatite, produced the typical low-phosphorus, porous martite-microplaty hematite ores of the Tom Price-Whaleback type. However, evidence of both microplaty hematite and martite reduced to magnetite, and of infill silica, apatite, and ferroan chlorite, with late-stage pyrite, in the pore space of martite-microplaty hematite ore, shows that the hydrothermal activity at Mount Tom Price is a post-ore event. Neither pyrite nor ferroan chlorite could resist the oxidation required to form hematite ore. Recrystallisation of microplaty hematite in these infilled zones to a typically coarser form than present in most of the normal ores, is a further supporting factor. A more credible, post-ore alternative to the hypogene genetic model is suggested here. Re-exposure to leaching by ground water of the metamorphosed ore deposits in the Phanerozoic resulted in the partial removal of remnant goethite. Localised modifications in the porous BIF/ore contact zones were driven by exothermic oxygen/pyrite/carbon reactions in the footwall Mt McRae Shale. Cool descending oxygenated meteoric water in the permeable ore horizons, acted as one limb of a thermal convective cell. In the other limb, heated reducing solutions rose through the permeable contact zones, to produce the observed localised modifications of BIF and ore. Expelled silica from the carbonatised BIF invaded adjacent porous ore to form erratic silicified ore zones, and to produce the local quartz vein systems found in the associated overlying BIF.

Jan 1, 2002

By Eugene Frey

"INTRODUCTION The Good Fortune mine was sampled by an engineer of the Bureau of Mines in June 1944. Project 984 was set up under the strategic minerals program to make old workings accessible for this sampling program. Actual operations commenced June 1, 1944, and were completed June 30, 1944.The deposit was visited and discussed briefly by Sidney H. Ball 3/ of the Federal Geological Survey in the summer of 1906 and by H. M. Chance 4/ several times from 1887 to 1900.LOCATION AND ACCESSIBILITYThe Good Fortune mine is situated in the Hartville mining district in Platte County, Wyo., approximately 9 miles northwest of the town of Guernsey. The property is about 100 miles north of Cheyenne, Wyo. (fig. 1).ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metal¬lurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

1. New books P. Sarnoff. Trading in gold. Cambridge, Woodhead- Faulkner, 1980. 136 pp. £3.50 by airmail. Environmental Planning Professions Interdisciplinary Committee (EPPIC). Proceedings: Joint EPPIC/Habitat Symposium: Shaping Our Environment. Johannesburg, EPPIC (P.O. Box 61019, Marshalltown 2107), 1980. R3 per set of 2 issues. H. P. Patra and K. Mallick. Time-varying geoelectric sounding. Amsterdam, Elsevier, 1980. 420 pp. D.S. $87.75. Die Suid-AfrikaanseSteenkoolverwerkingsvereniging. Steenkoolvoorbereidingskursus. J ohannes burg, die Vereniging, 1930. 335 pp. Members of Chamber of Mines of South Africa R15, nonmembers R40. D. R. Derry. A concise world atlas of geology and mineral deposits. London, Mining Journal Books, 1980. HO pp. £26.25 byairmail. 2. Journal Remote sensing of environment (RSE). 3. NIM reports Report No. 2064 The on-line monitoring of gold in barren solutions. Report No. 2065 The determination, by X-ray-fluorescence spectrometry, of gold, silver, and base metals on activated carbon. Report No. 2068 The determination of platinum, palladiuim, rhodium, and gold in ores and concentrates by the fusion technique with lead as the collector. Report 2061 The determination, by anodic-stripping voltammetry, of copper and lead in silicate reference materials. Report 2062 The reduction by computer of photoplate data obtained by spark-source mass spectrornetry. Report 2071 The determination, by X-ray-fluorescence spectrometry, of tin and tungsten in scheelite and ca8siterite ores and concentrates. Tunnelling Tunnelling '82, the third international symposium in the series, is being organized by the Institution of Mining and Metallurgy, with the co-operation of the British Tunnelling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory.

Jan 1, 1980

By Ruiqing Li

It is possible to purify some liquid metals by exploiting the difference between the vapour pressure of the bulk metal and the minor constituents or impurities. The rates of purification can be improved by carrying out the process under reduced pressure, that is, so called, vacuum. Some commercial examples of vacuum refining are the purification of molten tin to eliminate trace amounts of lead and the refining of cobalt, also to remove lead. The objective of this paper is to review the basic theory behind vacuum refining technology in order to show how the feasibility of vacuum refining can be determined simply for a particular system by evaluating Olette's Volatility Refining Criteriont.

Jan 1, 1991

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By T. A. Rickard

The history of this State is that of one generation. Thirtysix years only have elapsed since the birth of that beneficent industry whose footsteps were the first to traverse the wilderness of the prairies and penetrate the solitude of the mountains. So soon is history made. The men who halted on the rolling plain where Denver now stands and gazed westward at the snow-clad ranges in eager questioning of their possibilities of golden wealth, have lived to see a noble city built where once their camp-fires burned, and have participated in the discovery of a magnificent series of productive mines amid the mountains which seemed at that time the Ultima Thule of their pilgrimage. To those who investigate the workings of our complicated mining and metallurgical industries, the story of their evolution from humble beginnings will appear an instructive romance. The record that tells it presents features common to the growth of modern mining regions, but also bears aspects peculiar to

Jan 1, 1897

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80 000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100 m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size.IntroductionIron Oxide Copper Gold (IOCG) deposits are copper and gold ores hosted within a large body of iron oxide and are significant ore deposits for copper and gold (Williams, et al., 2005). These deposits can also contain economic levels of other metals such as uranium and rare earth elements. The known sizes of IOCG deposits range from 10 to 4,000 million tonnes with grade of 0.2-5% copper and 0.1-3 g/t gold. One of the greatest IOCG deposits is Olympic Dam in South Australia. It is the fourth largest copper deposit and the largest uranium deposit in the world. Gold and silver in the deposit also contribute significantly to the total revenue."

Jan 1, 2017

By I. Marklund, W. Hustrulid

Sublevel caving is likely to remain the dominant system at both Malmberget and Kiruna for the foreseeable future. The sub-level interval has increased from 12 m in 1983 to 30 m, requiring more effective drifting and the development of a contour blasting technique to reduce requirements for rock reinforcement. Production drilling is mainly by hydraulic hammers or water-powered in-the-hole machines drilling 115 m diameter holes. Loading operations are undertaken 7 days/week with 15-25 tonne capacity electric shovels. Production has increased by nearly 70% since 1983 and productivity has risen threefold

Dec 1, 1995

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

Physical/Chemical Treatment of Mercury-Contaminated Wastes from Former Chlorine-Alkali Electrolysis Plants - Application of Flotation Technologies in Soil Washing Plants

Sep 13, 2010