Search Documents

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

Jan 1, 1964

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O'Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By D. P. Harris

This paper examines recent developments and work in progress on the application of quantitative methods and computers to the appraisal of the mineral resource potential of discrete areas by employing reconnaissance geological information and general economic relationships. The perspective of this paper might be that of a firm planning a regional exploration program or of a legislative body seeking to choose between several alternative actions on the basis of their impact upon the regional resources. In addition to this general survey and commentary, an example is presented of the use of geostatistical analysis and computer simulation to evaluate the economic mineral resources of the Seward Peninsula of Alaska.

Jan 1, 1969

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By L. Russell Van Wert

DURING an investigation in which the solubility relations of the phases in Muntz metal (60 per cent. copper, 40 per cent. zinc) were under study, certain phenomena that had no immediate connection with the main problem were observed, which were thought sufficiently interesting to study further. Because of lack of time, only a preliminary survey was made of two of these; namely, the cleavage structure developed under certain conditions in a 60:40 brass and abnormal grain growth in this alloy. CLEAVAGE STRUCTURE IN HEAT-TREATED MUNTZ METAL Carpenter noted many years ago that cold-working a brass of the Muntz metal type, which had been quenched previously from within the beta field, results in a partial breakdown of the supersaturated beta solution and the precipitation of the solute (the alpha solution) in the cleavage planes of the beta grains. This manner of rejection of a solute from a metastable solid solution is not peculiar to this particular alloy, for among others, it occurs in the cold-working of certain austenitic steels; for example, the austenitic nickel steels. In these ferrous alloys, cold deformation produces a partial decomposition of the austenite, with the formation of martensitic "needles" and zigzags in the austenitic poly-hedra. It is interesting to note that while the two solid solutions-austenite and quenched Muntz metal- are metastable and in their mode of decomposition behave quite alike when deformed in the cold, the metastability of each results from a different cause; viz., that of the austenite from the fact that it is a supercooled solution (its solvent, gamma iron, at ordinary temperatures is below its normal stable range) whereas the metastability of the quenched Muntz metal is the result of supersaturation.

Jan 1, 1929

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Nicholas J. Grant, H. C. Chang

TRANSCRYSTALLINE fracture surfaces of the cleavage type have been examined by microscopy and X-rays for several metals.' These investigations revealed that the fractured surfaces were not flat and invariably had cleavage and other deformation markings on them. On the other hand, the study of inter crystalline fracture surfaces has been limited. Perryman, in a recently published paper on the inter crystalline fracture of ß-brasses,' found that a thin layer of heavily deformed metal was invariably associated with these surfaces. Furthermore, the thickness of this layer was found to depend on the orientation of the grain boundary surface with respect to the applied stress. The mechanisms of grain boundary sliding and intercrystalline fracture have been presented in two previous papers,which described certain aspects of the deformation of a 20 pct Zn-A1 alloy. It is the purpose of this paper to present some observations on the structure of intercrystalline fracture surfaces and to correlate the structure of such surfaces with the mechanism of intercrystalline fracture. Experimental Techniques—The high purity 20 pct Zn-Al alloy was generously supplied by the Research Laboratories of the Aluminum Co. of America. Two sizes of specimen were used; the first had two parallel flat surfaces of dimensions 1x0.17x0.09 in. and the second was round with a 0.25 in. diam. A grain diameter of 1 to 3 mm was obtained by annealing the specimens at 1000°F for 24 hr. The specimens were then air cooled. The specimens were subjected to creep at 500°F and 2300 psi. The rupture times ranged from % to 3 hr, with one room temperature tensile test. It has been mentioned previous1y" that the intercrystalline fracture surfaces of this alloy, when tested under the conditions given above, are sharply defined. In the optical examination of the fracture surfaces, whenever possible, magnifications of at least X250 were used. The locations of the regions examined, both optically and by X-rays, were selected to give several fracture surface orientations with respect to the stress axis and to the specimen surfaces. This was possible for the X-ray studies since the grain diameters were large compared to the X-ray beam. A film to specimen distance of 3 cm, a 1 mm pinhole and Cr radiation were used for the Laue back reflection pictures.

Jan 1, 1957

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961