Search Documents

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940