Search Documents

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By Irvin G. Burough

ANDROS INCORPORATED has designed, manufactured and delivered four handheld C02 DETECTORS and three handheld CH4 DETECTORS. These instruments are for in-mine safety use. The DETECTORS incorporated an NDIR optical/electronic analyzer design in which exceptional zero stability is achieved by pressure modulation of the sample gas. This eliminates the need for daily calibration. This stability and the miniature design (2.5" x 4.5" x 4.5"; 4.5 lbs) of the C02/CH4 DETECTORS provide practical instruments suitable for routine safety inspections. This report includes the theory and design of the instruments as well as studies of gas-pressure modulation by a piezoceramic-driven Helmholtz resonator.

Jan 1, 1979

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

By R. V. Ramani

Procedures have been developed which permit determining in either existing or new mines the optimum diesel equipment deployment schemes and the effect of. diesel exhaust on mine-air quality. Specifically, the following areas are covered in the report: 1. Description of diesel deployment schemes in four underground coal mines that were visited is provided. 2. Description of the analysis procedure to determine the number of shuttle cars required to maintain maximum theoretical continuous miner (or loader) production rates in typical room-and-pillar mining systems and of exhaust contamination resulting from the deployment of diesel powered shuttle cars are provided. Sensitivity analyses to determine the effect of changes in input variables on production and contaminant concentrations are also discussed. 3. Description of the analysis procedure to develop the locomotive operating parameters is provided. Assessment of both production performance as well as estimates of the magnitude of diesel exhaust contamination of the mine air are also made. 4. Recommendations for extensions of this research are outlined and include developing and testing procedures for 1) determining equipment duty cycles for the diesel equipment, and 2) studying the exhuast contamination of mine air on the basis of these duty cycles.

Jan 1, 1978

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By L. A. Morely

Volume II of the final report concerns the application of sensitive ground-fault interrupters (GFIs) to ac utilization circuits in U.S. mines The main concepts examined are shock prevention and methods for reducing nuisance tripping. The research involved a literature search, input from previous Bureau of Mines contracts, and contacts with electrical manufac-turers and mining personnel. Following this background work, several devices that showed promise were obtained and tested. Results of testing indicate the existence of GFIs that may be modified to perform adequately on U.S. mining systems. A recommended set of guidelines is included in the report, covering design, construction specifications, and performance tests.

Jan 1, 1982

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By W. S. Sanner

Anthracite was used extensively as a fuel in iron metallurgy from 1840 to 1880. In 1874, 226 of the 680 blast furnaces in the United States were operating on anthracite and producing almost one-half of the Nation's pig iron. However, by 1890, railroad expansion, the development of western iron-ore reserves, and the growing use of coke decreased the importance of anthracite as a metallurgical fuel. As a result, the last blast furnace designed exclusively for anthracite use was built in 1891. Because of the increased energy requirements of our expanding national economy, the abnormally high demands during national emergencies, and the proximity of anthracite deposits to eastern steel-producing areas, interest has grown in again using anthracite in iron metallurgy. Estimates of anthracite reserves indicate a 300-yr. supply at a production rate of 30 million tons per year. These large reserves dictate the development of an adequate technology for the use of anthracite by the metallurgical industry.

Jan 1, 1961

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962

By W. L. Brien, O&apos

Molybdenum alloys with good strength properties at elevated temperatures were produced by the powder metallurgical internal oxidation method previously applied to tungsten and known as oxyreaction strengthening. Commercial molybdenum powders were blended with 0 to 10 pet of a reactive powder, ZrMo2. The effects of composition, blending procedure, and sintering conditions on strength properties at elevated temperatures were studied. Strengthening was attributed to zirconium in solid solution with molybdenum and to the presence of submicrometer particles of Zr02. Several alloys had tensile strength and stress-rupture properties com-parable with those of the best commercial alloys. The maximum tensile strengths obtained were 92 kpsi at 1,200° C and 53 kpsi at 1,316° C. The maximum stress-rupture life at 30 kpsi and 1,200° C was 145 hours.

Jan 1, 1974

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from ~0.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from 4.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979