Search Documents

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Michael McDonald

The cold-rolled steel output of cold-rolling mill (CRM) complexes are sometimes constrained by their batch annealing facilities (BAF). This paper examines a cost-effective solution to increasing capacity and quality of the BAF thereby making additional capacity available for CRM output. The solution involves applying a structured system of scheduling and operation to the BAF, using a proven level-2 software model. The system presented has been applied to a wide variety of BAF with all the leading furnace brands. Whether using traditional HN atmosphere or 100% hydrogen, peak performance can be achieved when using a properly configured, on-line, physical thermodynamic model. Given that it is not practical to place a thermocouple in each coil that is being annealed, various methods have historically been used to estimate the time required to properly anneal all the coils in the charge. This paper examines how the latest technology, in wide use throughout the USA, uses a physical thermodynamic model to shorten average cycle times, thereby increasing productivity and reducing energy consumption. The paper also examines the benefit of building thermodynamically balanced charges to further optimize the BAF operation and improve quality consistency by decreasing mechanical property variations.

Jul 30, 2018

By Alberto Pesamosca

The paper presents the results obtained by the AC EAF supplied by Danieli at Kroman Çelik (Gebze-Turkey) after the planned upgrade to 150 ton. The EAF – 7,4 m diameter, based on the full platform standard design - is able to handle a maximum power of 114 MW and is equipped with the most advanced and reliable technology, including module injection system and the Hireg electrodes regulation system. Excellent results were already obtained with 120 heat size in terms of fast start-up and excellent performance figures. After the upgrade, productivity was increased up to 212 t/h, maintaining high process efficiency (365 kWh/t with 32,1 Nm3/t O2).

Jul 30, 2018

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Mohammad Masoumi

In the present study, API 5L X70 pipeline steel samples were deformed by hot-rolling cooled in air or quenched in water and subsequently tempered at different temperatures. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) technique were used to analyze the texture evolution from the initiate state to rolling and tempering state at mid-thickness and near surface plane of all samples. The results showed that the mid-thickness region is richer in {100}//ND oriented grains known as more susceptible to crack formation and growth through. Hot deformed specimen showed dynamic recrystallization grains while quench tempered sample at 700°C evidenced recovery and grain growth.

Aug 16, 2017

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019

By Rodrigo Sanchotene Silva

Currently the industries of paint have directed their efforts on cleaner production of products that provide effective performance in corrosion protection of metallic materials. This work search introduce a new alternative of organic coating, without the presence of hazardous metals and replace equipments commercials used method of anodic protection for protection of oxidized metals. From this it, was produced Smart Paint (SP), consisting of Paint Acrylic Commercial (PAC) mixed the 1 % of binder, compound by the conducting polymer, Polyaniline Emeraldine Base (PAni EB) and plasticizer 4-chloro-3-methylphenol. The SP and PAC were applied to plates of carbon steel AISI 1010, with the aid of dip coat technique and then were subjected to drying for 48 h. The SP was characterized by thermals and physicochemical analyzes in order to verify possible changes in chemical properties of the ink produced, beyond perform electrochemical tests of Open Circuit Potential and Electrochemical Impedance Spectroscopy, employing equipment Potentiostat/Galvanostat Autolab PGSTAT302 Ecochemie, and aqueous 2 mol.L-1 of H2SO4. The results obtained allow us to state that the plasticizer does not alter the electrochemical properties of PAni and application of binder PAni EB to PAC does not alter the physicochemical properties of commercial coating. The binder PAni EB adds to PAC the capacity to induce the formation or maintenance of protective oxides in oxidizable metals submitted to harsh environments, method known as anodic corrosion protection.

Aug 8, 2018

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017