Search Documents

By R. D. Leitch, W. P. Yant, R. R. Sayers

In 1924, the United States Public Health Service was requested to undertake a special study of stream pollution. The Public Health Service asked the United States Bureau of Mines to take up the study because the training and experience of the personnel of the former was considered not to be as well suited to this type of investigation as that of the Bureau of Mines. Under H. Foster Bain, then Director of the Bureau, field investigations were begun in the spring of 1925. Along with mine-drainage wastes, the problem of gas-house and coke-oven waste was investigated in the laboratory and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau Experiment Stations, on a trip to Germany in 1924. He saw a practical application of the process, but obtained no information as to definite chemical or mechanical processes. Because of the then pending American patent applications by the German firm, we made no attempt to develop our findings further. Shortly afterward, a similar method of treatment was developed in the United States,' and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage. Scope of Work There was such a diversity of opinion at the time this work was begun, on the whole subject and apparently so little accurately known, that it was decided to undertake a basic study from which first, certain definite information might be evident, and second, what might be considered

Jan 1, 1931

By C. E. Turner, J. R. Elenbaas, R. D. Grimm, J. A. Vary, D. L. Katz

A technique is presented by which well samples and core plugs of dolomite formations are classified by microscopic examination into seven different porosity grades. Quantitative values of porosity and permeability are determined for each grade by a statistical correlation of the core plug test data with the porosity grading system. These quantitative values are applied directly to the grades exhibited in the well samples for the purpose of estimating the reservoir void space for wells that were not cored. The procedure is described for estimating the gas reserves per unit area lor the South Hugoton gas field. but a reserve estimate for the field is not given. INTRODUCTION The miscroscopic examination of well sample; and the graphic recording of their lithologic qualities and other distinguishing characteristics of various geologic formations drilled is both a science and an art of long standing and wide application. Usually the primary objective of a geologist who "sits on the well" and examines the samples are: to identify the formation being drilled, determine the total depth, casing point. and completion interval. In most cases the porosity is described. if done at all, in general terms. such as: trace, scattered, fine, poor, fair, medium. good, excellent, or in some other relative terms. In fields where various geologists have examined samples and recorded observations on many wells considerable variations in lithologic terms and porosity descriptions occur unless there is primary effort to establish uniformity of logging observations and standards of recording observable porosity. When an estimate of the pore volume of a reservoir is made a geologic concept of the processes that control the magnitudes of porosity and permeability is developed by microscopic examination of well samples. The characeristics and appearances are then mentally related to rather general quantitative units of porosity based on physical core data from the same reservoir or on such data or experience in other reservoirs that have similar qualities. The reliability of such estimates depends largely on the variations of the lithology of the formations, the geometric properties of its void system. the extent of comparisons of sample appearances with porosity data, as well as the uniform recording of all relevant characteristics. This statement is particularly significant for dolo-mitized limestone formations of substantial thicknesses and heterogeneity such as the Permian Dolomites of the Hugoton gas field. Jn this field, as well as in most of the Permian Dolomite fields, the producing formations are of relatively great thicknesses in which the porosity and permeability of the reservoir varies substantially in all directions, depending on the crystalline structure. degree and kind of impurities, kind of fossils anti cementation thereof, degree of dissolution. and fracturing. The variations of the lithologic texture of the dolomites and post deposition alterations have resulted in porosities and permeabilities of such magnitudes that only a part of the gross thickness can be counted as "pay." At the time of this study insufficient gas production had been experienced to apply the pressure decline production method in the South Hugoton Field and the electric logs are not definitive enough. The problem of estimating gas reserves in the south part of the Hugoton Field is primarily one of determining the pay thickness and porosity from well samples and core data. The area studied embraced all that part of the field lying south of an east-west line through Guvmon, Okla., anti containing approximately 1.000,000 acres. This paper describes a technique of correlation of physical core data with well samples so that quantitative values of pay thickness, porosity. Permeability, and connate water may be assigned to well samples that are representative of a given interval, and thereby permitting the estimation of gas reserves lor a given unit area. The procedure was developed by a uniform microscopic qualitative porosity grading of the dolo. mite core plugs.. and relating these grades to the respective physical core data on a statistical basis The well sample-were also graded in a Similar manner in order that the quantitative values established lor the core plugs could be applied to the well Sample for wells that were not cored. GRADING OF DOLOMITE A group of experienced geologists was given the assignment of examining the samples on all wells in South Hugoton in order that they could log their observations in a uniform and standardized manner and grade the observed porosity so that it could be related quantitatively to the core data. The group initiated the study 011 chips from cores which bad been tested for porosity and permeability. This study continued until all of the geologists developed a common knowledge of lithologic terms and of the characteristic appearances of the samples and their relations to measured porosity. The characteristic appearances of the dolomite samples under twelve-power magnification as related to their qualitative porosities afforded a classification of the dolomite into :even grades of porosity, ranging from dolomite of no-visible porosity under twelve-power magnification to dolomite of excellent porosity. The assigned grade for a specific 10-ft interval is a weighted average of all visible grades of porosity exhibited by the cuttings representing that interval. The porosity characteristics were recorded by a color graph adjacent to the lithology column in conjunction with a numerical system for further definition of relative porosity as shown in Fig. 1. The three vertical lines to the right of the lithology column each represent 33 1/3 per cent. which lines were used to record the percentage of the samples, for any particular interval. that showed porosity under the microscope. The colors were used to denote actual pore size. i.e., orange. blue and I-ed for pore diameter of one-fourth or less. one-fourth to one-Ilalf. and greater than one-half millimeter, respectively. The area colored 1)). one or more colors represents the percentages of the samples exhibiting pores of the respective size or sizes. The numerals from one to six inclusive shown on the log in

Jan 1, 1952

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By D. M. Dunbar

LONG before Columbus discovered America the original inhabitants toiled in the copper workings of the Andean Cordillera. Their best diggings appear to have been at Chuquicamata, site of the huge present-day open pit owned by the Chile Exploration Co., subsidiary of Anaconda Copper Mining Co. Located in Antofagasta Province of northern Chile, Chuquicamata is in the Atacama desert, high on the western slope of the Andes at 9500-ft elevation. In the Chuquicamata area the Atacama desert merges into the Cordillera. The climate is extremely arid and precipitation, either in the form of rain or snow, is very infrequent. The temperature varies from 50° to 85°F during the day, and drops to 20° to 40° at night. The Antofagasta and Bolivia Railroad, which connects the Chilean Port of Antofagasta with La Paz, Bolivia, passes within approximately 6 miles of the plant. A branch from the main line to Chuquicamata serves the property for outgoing copper and incoming freight. The distance to Antofagasta by rail is 163 miles. Previous to the Inca conquest, this region was inhabited by the Chuco Indians, a small tribe, descendants of the Aymaras and Quechuas. The Incas, whose capital was located in Cuzco, Peru, gradually extended their empire to the south, reaching at one time to what is now central Chile. It is believed that they built crude primitive furnaces on the banks of the Rio Salado where on a small scale they smelted copper ore from Chuquicamata. At the time of the subsequent Spanish conquest, legend has it that Diego de Almagro, on his return to Cuzco in 1536 after his invasion of Chile, obtained from these furnaces metallic copper for horseshoes. During the period from 1560 to 1879 the high grade veins of the Chuquicamata deposit were worked superficially by the Spaniards and Bolivians. The treaty signed after the war of 1879 recognized the sovereignty of Chile over this territory and Chile, realizing the importance of the district, started to develop it in an orderly manner, although only high grade veins were worked. New Process Is Key Reports on the deposit were brought to the attention of Albert C. Burrage, a Boston lawyer and financier, in 1910. Chuquicamata was described as a huge deposit of ore that was not amenable to the usual treatment by concentrating and smelting since much of the copper occurred as oxides. He had been working on a process for the recovery of copper from sulphide ore which involved a sulphating roast, leaching of the roasted product, and pre-

Jan 1, 1952

By Thomas W. Dawson

The H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnages and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center to center of pulleys. It operated at a speed of 250 ft. 'per min-and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons was carried by the belt. whi1e: this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and, therefore, had to be crossed at each location to deliver coal to the river. After careful study, it was decided to transport this coal from the hoisting shaft to the river at each of these plants by belt conveyors.

Jan 1, 1925

By K. D. Snyder

Barite deposits occur in the Iglesiente-Sulcis district of southwestern Sardinia, an historically important lead-silver-zinc district. Barite, often genetically associated with the base metal deposits, has become an independently important economic commodity. Barite deposition in southwestern Sardinia was related to Caledonian, Hercynian, and Alpine orogenic cycles. A model is presented that relates synsedimentary, karstic, vein, and residual deposits. Synsedimentary deposits are widespread, have common depositional characteristics, and act as sources, along with hydrothermal systems, for other barite deposit types. Caledonian-, Hercynian-, and Alpine-related secondary enrichment processes resulted in residual and karstic deposits that are complex in terms of their geometry and texture, but are more economically important than those of synsedimentary or hydrothermal origin.

Jan 1, 1985

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By A. V. Bradshaw, R. I. L. Guthrie

The behavior of large bubbles in the size range 4 to 25 cm3, rising through molten silver, has been studied. It was found that rising velocities were equivalent to those in aqueous systems of low viscosity. Mass transfer coefficients for oxygen bubbles dissolving in silver were found to be 0.036 ± 0.007 cm sec-1, being close to those predicted for transfer through the front surface of the spherical cap bubble only. It is suggested that the surface active nature of oxygen in silver could account for the relatively low coefficients obtained. MANY metallurgical processes involve interactions between gas bubbles and liquids. Examples include the removal of carbon monoxide in Open Hearth Steelmak-ing, the removal of sulfur by blowing air through copper matte during converting, and the removal of hydrogen from steel during vacuum degassing or inert gas flushing. The steps involved in such refining processes include; transport of the dissolved species to the bubble interface, adsorption and chemical reaction of the species at the interface, desorption of product molecules from the interface, and transport of product gas into the bulk gas phase of the bubble. It has been concluded1 that all the interfacial steps involved proceed so rapidly at steelmaking temperatures that transport of the solutes, present in the metal, become the important rate controlling factors provided nucleation phenomena are not restrictive. The O-Ag system was chosen for the investigation into gas bubble-molten metal interactions due to the relatively high solubility of oxygen that enables rates of oxygen transfer to be measured from changes in bubble volume. Other advantages of this system include the absence of a stable oxide phase at an oxygen pressure of 1 atm and the relatively low melting point of the metal which permits the use of a metallic container, providing that it is resistant to oxidation. In those metallurgical processes where bubbles have an important influence, bubble volumes are usually greater than 5 cm3. For this reason the present study relates specifically to single large bubbles of oxygen rising in silver. These bubbles adopt the characteristic spherical cap shape similar to that shown in Fig. 1 for a 30 cc bubble rising in water. After an initial investigation to determine the velocities of inert (nitrogen) bubbles rising in molten silver, experiments were carried out with oxygen and the rates of mass transfer between the oxygen bubbles and the silver were measured. EXPERIMENTAL Apparatus. The apparatus, Fig. 2, for containing molten silver, was constructed from "Nimonic 75" Alloy (75 pet Ni, 20 pet Cr, 5 pet Fe, Mn) and provided for the release of single bubbles from an hemispherical cup, situated at the bottom of the column. The cup was turned by translating the rotation of the drive shaft through 90 deg. This was accomplished by the use of a bevelled gear system, and a smooth drive was provided by the lubricating action of the silver on the gears. Since reliable high temperature seals at 1000°C were found to be impracticable, the filling and drive shaft tubes were extended outside the 3.5 kw resistance wire tube furnace, where connections were made using easily accessible O-ring seals. The apparatus remained gas tight to the atmosphere at pressure differentials far in excess of those used. The filling tube was connected via a small bore tube to the differential pressure transducer. Gas could be bubbled into the inverted cup from two i-in. tubes which passed down the inside of the column to preheat the gas. The temperature of the silver was maintained at 1020°C during all experiments. Measurement of Bubble Volume. In order to calculate mass transfer rates, it was necessary to obtain a continuous record of the bubble's volume during its passage through the column of molten silver. The method adopted for measuring the bubble volume involved closing off the top gas space to the atmosphere prior to each experiment, and recording the variation in gage pressure of this space during the formation and rise of the bubble. Since any change in bubble volume results in an equal change in top space volume, Boyles Gas Law may be applied (for isothermal con-

Jan 1, 1970

By Norman Brown, Victor V. Damiano

ThE present paper proposes a mechanism of dislocation multiplication at internal inclusions or cavities and presents experimental evidence of such sources in zinc. Using an etching technique recently described by Damiano, Tint, and Herman1 to study the three-dimensional aspects of dislocations in bulk zinc crystals, an investigation was made of helically shaped and closed-loop etch patterns found to be associated with inclusions. Crystals containing 0.1 pet Cd and grown from the melt were deformed slightly by bending and then aged at room temperature to precipitate cadmium at the dislocations. The crystals were cleaved along the (0001) plane and then etched with Gilman's2 etch. Crystals were continuously viewed on the (0001) plane while the etching was in progress and numerous helical and closed-loops etch patterns were continuously recorded as shown in the sequences printed directly from the cine film in Fig. l(a) and (6). These etch patterns are not to be confused with the etch patterns previously reported by Damiano and Herman3 which revealed dissolution spirals on the (0001) plane of high-purity zinc crystals. In the present case, precipitates arranged in the form of closed loops or helicies are progressively uncovered by etching after suitable aging of cadmium doped zinc crystals. Viewed with dark-field illumination as shown in Fig. 2, portions of a helical figure and subboundaries were revealed simultaneously. Continuous viewing while the etching was in progress revealed in Fig. 1(b) that the short line segments observed on single photomicrographs were in fact continuous and described a helix which had its terminus at an inclusion. The observations suggested that a dislocation once nucleated at the interface between the inclusion and matrix may act in such a way as to produce ad-

Jan 1, 1964

The meeting of the Board of Directors, on November 22, was attended by eight directors, the Secretary of the Institute, and eight guests. The proposed James Douglas Prize and Tablet was referred to a committee of eleven. Robert H. Richards was appointed representative of this Institute to attend the meeting of the Society for the Promotion of Engineering Education. J. V. N. Dorr was made chairman of the Finance Committee in place of George D. Barron, resigned. The sum of $200 was appropriated for the 1918 expense of the American Engineering Standards Committee; the question of an appropriation for 1919 was referred to the Executive Committee for study and report. The sum of $50 was appropriated to the Treasurer's clerk. The following representatives of the Institute were elected: W. L. Saunders to succeed himself as United Engineering Society Trustee; R. M. Raymond to succeed himself as member of Engineering Foundation Board; S. J. Jennings to succeed himself as member of Engineering Council; George F. Kunz to succeed himself as member of Engineering Council; C. F. Rand to succeed himself as member of John Fritz Medal Board of Award; E. Gybbon Spilsbury to succeed himself as member of the Library Board. To members of the Canadian Mining Institute residing in Canada or Newfoundland, the privilege was extended to subscribe to the Bulletin at the price of $5. An invitation was extended to the Mining and Metallurgical Society of America to consolidate with the American Institute of Mining Engineers. The appointment of Engineering Societies' Employment Bureau was reported. Thirty-nine members and ten associates were elected. Two members were reinstated. Extension of time for the payment of clues was granted to four members. Seventeen members on active duty at the front had their dues remitted.

Jan 1, 1919

By Bernard K. Asdell

Georgia, a state seldom considered to be an important mineral producer, has one surprising feature-it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite.

Jan 11, 1967

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By C. L. Magee, H. W. Paxton

PREVIOUS workersl'% ave found that as-quenched ferrous martensites can be plastically deformed at low stresses. They have also found that the stress to obtain small strains can be significantly increased by aging at temperatures up to 150°C. This behavior has been interpreted in two ways: 1) that the deformation at low applied stress is due to internal stresses and thus the aging phenomenon is due to relaxation of the internal stresses;' 2) that the microdeformation arises through the motion of unpinned dislocations and the aging process is the diffusion of carbon to the dislocations to pin them.293 In a recent paper,4 we have shown that under certain conditions the dominant microdeformation mechanism of as-quenched Fe-31Ni marten-site-austenite aggregates is the transformation of retained austenite. Our results on resistance changes during deformation and temperature dependence of the deformation also established that, at temperatures above 300° K, the microdeformation was not due to this transformation. The purpose of this note is to report results of experiments which indicate that explanation 1 is appropriate for this deformation. All results presented here are from conditions where transformation does not make a measurable contribution to the microplastic deformation, in Fe-31Ni-0.002C, or in Fe-29Ni-0.02C-0.25Ti. The experimental techniques that were used for measurement of the plastic deformation are described4 and analyzed5 elsewhere. Fig. 1 shows the microplastic response of 100 pct austenite at 300" and 350° K. The microplastic response of an austenite-martensite aggregate is also given in Fig. 1 and it is seen that, after formation of martensite, the initial plastic deformation occurs at lower stresses. Thus, the softness is not entirely due to retained austenite—the quenched structure can be deformed at lower stresses despite the fact that the macroscopic strength is significantly higher. A result which allows a distinction to be drawn between the alternative explanations for this behavior is derived from aging experiments on the low-carbon alloy containing titanium. We have previously shown4 that the presence of titanium in this alloy reduced the free carbon to a sufficiently low level that thermal stabilization of the austenite-martensite transformation was not detected. Despite this, Fig. 2 shows that the microplastic response is decreased by aging treatments. A similar aging effect in Fe-ZONi, with some titanium, has previously been reported by . Thus, carbon is not necessary for the aging process and explanation 2 is at best incomplete. Since internal stress relief can occur independently of carbon (any temperature dependence of the flow stress can result in decreased internal

Jan 1, 1969

Jan 1, 1940

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By D. B. Carson, D. L. Katz

Natural gases under pressure form crystalline hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methanc-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbon-rich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. Introduction Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural-gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villardl and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Dcaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on tem-peraturcs and pressures of hydrate forma. tion for pure methane, ethane, propane, n-butane, methane-ethane mixtures, meth-ane-propane mixtures, methane-butane mixtures, and some Is natural gases, all- in the Presence of excess water. However, up to the Present time no method has been available for predicting the temperature at given pressures or the pressure at given at at which natural gases will form hydrates if hydrates with water. 'This Paper Presents data on the methane-propane-water, methane-pentane-water and methane-hex-""e water systems in four phases, one of which is the hydrate. he application of the phase rule to the methane-~ro~ane-water data Proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid. equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1942

By D. B. Carson, D. L. Katz

Natural gases under pressure form crystalline hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methanc-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbon-rich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. Introduction Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural-gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villardl and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Dcaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on tem-peraturcs and pressures of hydrate forma. tion for pure methane, ethane, propane, n-butane, methane-ethane mixtures, meth-ane-propane mixtures, methane-butane mixtures, and some Is natural gases, all- in the Presence of excess water. However, up to the Present time no method has been available for predicting the temperature at given pressures or the pressure at given at at which natural gases will form hydrates if hydrates with water. 'This Paper Presents data on the methane-propane-water, methane-pentane-water and methane-hex-""e water systems in four phases, one of which is the hydrate. he application of the phase rule to the methane-~ro~ane-water data Proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid. equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1942

By H. R. Peiffer, R. Geckle

The silver phase of silver and finely divided alumina composites is shown to grow as single crystabs upon solidification from the melt. These crystals grow without the aid of an externally applied thermal gradient or a mold. The single-crystal growth is more readily disrupted as the alumina content varies from the optimum concentration of 20 wt pct. Pretreatment such as variation of fabrication pressure, and presintering of the specimens appear to play a lesser role in this phenomenon. In actual practice the growth of single crystals of metals from the melt is a tedious, painstaking process.' Care must be taken to insure the proper thermal gradients and rate of growth in a vibration-free environment. Excellent single crystals can be grown when these variables are controlled. When a second insoluble and finely divided phase is present in the melt the growth of single crystals is difficult, if not impossible, even under the most favorable conditions outlined above. During the past few years, a composite of silver and alumina has demonstrated an ability to resist flow even though the major phase, silver, is mo1ten. 2 A more surprising feature of this material is the ease with which single crystals of silver grow upon cooling the composite from temperatures above the melting point of silver to temperatures near room temperature. Observations have been made that demonstrate that single crystals of silver will grow even when conditions most unfavorable for growth of pure silver crystals exist. The crystals grown in this manner are imperfect in that a great deal of subgrain structure exists. It is the purpose of this manuscript to qualitatively describe this process and to attempt to isolate the influencing factors of this behavior. MATERIAL PREPARATION The composite material is prepared by powder-metallurgical techniques. Two items of great importance are the introduction of oxygen into the system and the obvious need for a thorough mixing of the metallic and refractory oxide phases. The oxygen is necessary in order that the silver wets the alumina. Without oxygen the phases separate and the material shows no unusual properties. In order to supply the needed oxygen the silver is added in the form of silver oxide which is readily decomposed to oxygen and silver upon heating. The silver oxide is readily obtained in a finely divided form that allows a uniform mixture of the alumina and silver oxide to be prepared. The correct ratio of alumina to silver oxide is mixed in the presence of alcohol in an ordinary food blender. The mixture has the consistency of a thin slurry and after mixing for approximately 20 min is dried and pressed into billets at various pressures. As is shown in Fig. 1, there is no limit to the shape of the specimens obtainable as single crystals. These billets are heated in air in a predeter-

Jan 1, 1964

THE man who forgot to mail the letters his wife gave him was for once justified at Tulsa, for envelopes, scratch paper and tablecloths were all in demand and through the two days of the meeting of the Petroleum Division, pencils were busy everywhere sketching out diagrams, drawing curves, figuring, or just taking notes. Those attending took the serious papers seriously, and discussion was wide-ranging but pointed. Despite the highly technical character of the papers presented, the chairmen had never to call for discussion; it was only necessary to say the paper was open for it. Both days the meetings lasted until after five in the afternoon, and it was enthusiastically voted to advance the meeting hour on Friday, in order to give more time. In all, ten papers, abstracts of which appeared in MINING AND METALLURGY for October, and copies of all but two of which were available in print, were presented in the two days, and no more could have been handled to advantage in that time. All but one of these dealt with problems of production engineering. That, the opening paper, was a general review of demand, supply and price in 1928, by Campbell Osborn, in which he argued for the price control of production and showed how the economic conditions determined development. J. Elmer Thomas presented a carefully prepared review of the same data, but came to somewhat different conclusions as to trend, and J. E. Pogue pointed out that in recent years it has been the manufacturing rather than the producing industries that have been notably profitable. These and other discussions were too long to be reported here, but will be printed in full later.

Jan 1, 1928