Search Documents

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

By Robert Mehl

PART I. ORIENTATION RELATIONSHIPS IN OXIDE LAYERS Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical struc-ture in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of dis-covering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. TRANS-ACTIONS in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears, a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems-mineral or inorganic. In 1827 Haidinger2 dis-covered natural intergrowths of hematite and magnetite, and demon-strated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00-1):(10-1) in hematite lies normal to the [111]

Jan 1, 1937

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By Donald R. Rathburn, Jung K. Mok

An historical review and a survey of current practice in the application of fine dry grinding in the iron ore industry are given. Both closed and open-circuit applications are reviewed, and the advantages, disadvantages, and process considerations for these two systems are discussed. The ground ore temperature rise, and the cool-ing of ground ore and mill ventilation are also discussed, along with the agglomerating characteristics of dry ground ore. Screening during the production of high-grade lump ore for blast-furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date. Others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. In almost all cases some grinding is required prior to pelletizing. Most of these ores occur in the weathered state which may result in difficulty in the thickening and/or filtering stages when ground in a wet system. The resulting filter cake would probably require partial drying to provide a product suitable for the subsequent balling operation; however the partial drying and subsequent material-handling steps often produce random agglomeration. Normally, these agglomerates will cause problems in the green ball formation process. Thus dry grinding has developed as a solution to this problem. Most of the dry iron ore grinding installations utilizing the standard-type rod or ball mill are grinding high-grade natural ores that do not require beneficiation. Although power consumed per ton of final product is 120% or greater in dry grinding as compared with wet grinding, the additional power required for dewatering and handling a wet ground product can easily exceed the initial power savings. Dry grinding of raw feed and clinker has been practiced in the cement industry for many decades but its major application to the iron ore industry has taken place only within the past ten years. The successful application of dry grinding to iron ore has required the solution of several unique design and operating problems. The purpose of this paper is to review recent developments in fine dry grinding of iron ore for pelletizing and to discuss the various designs and operating parameters involved.

Jan 1, 1971

By William Benzon

Bethlehem Steel's Cambria Division coal cleaning and preparation plant, operated by Bethlehem Mines Corp., is located in Cambria County, Pa., about 2 ½ miles southeast of Ebensburg. Here, above ground, is the most modern coal preparation plant in the world. Below the surface is a new coal mine also referred to as "the most modern that could be built today." The preparation plant has a capacity of 1370 tons of clean coal per hr. It serves three Bethlehem mines, Heisley No. 31, Revloc No. 32, and the new Cambria Slope No. 33.

Jan 12, 1965

By Dennis J. McCarthy

TAX TREATMENT OF EXPLORATION AND DEVELOPMENT EXPENSES Exploration Expenditures General Principles. Exploration expenditures are expenses incurred within the United States or the Outer Continental Shelf for the purpose of ascertaining the existence, location, extent or quality of any deposit of ore or other mineral. Section 617 of the Internal Revenue Code permits a taxpayer to elect to deduct these expenditures currently. In default of election, exploration expenditures must be capitalized and included in the basis of the mineral property for purposes of determining cost depletion. Entitlement to Deduction. In order to qualify for current deduction, exploration expenditures must be incurred prior to the commencement of the development stage, i.e., when mineral deposits are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation. Generally, expenditures for geological and geophysical investigations, reconnaissance, surveying, testpitting, trenching, drilling, driving of exploration tunnels and adits and similar types of work constitute exploration expenditures if incurred prior to the commencement of development. However, expenditures to further delineate the extent and location of an existing commercially marketable deposit are not exploration expenditures. Exploration expenditures may be incurred from within a producing mine to ascertain the existence of what appears to be a different ore deposit. Expenditures for property which is subject to an allowance for depreciation are not deductible under §617. However, depreciation properly allowable on assets used in exploration is an exploration expenditure. Election to Deduct Exploration Expenditures. The election to deduct exploration expenditures is made by deducting these expenditures in the return for the first taxable year for which such treatment is desired. The election applies to all properties of the taxpayer. Once the election is made all exploration expenditures, in the year of election and thereafter, must be deducted, unless the election is revoked with the prior consent of the Commissioner. The Tax Equity and Fiscal Responsibility Act of 1982 (TEFRA) made substantial changes in the treatment of exploration expenditures. For exploration expenses incurred after 1982 and before 1984 by a corporation, the amount currently deductible is limited to 85% of the expenditure. The remaining 15% must be capitalized and recovered over a five-year period. Although exploration costs capitalized under this provision are not part of the basis of the property for cost depletion purposes, investment credit may be claimed with respect to these expenditures. Further changes have been added by the Tax Reform Act of 1984 with respect to expenditures made after 1984. The Act reduces the amount of otherwise currently deductible costs from 85% to 80%. Additionally, it limits the availability of the investment credit for capitalized mineral exploration costs to deposits located in the United States. TEFRA also allows individuals a special method of recovery under which exploration expenditures may, at the election of the taxpayer, be amortized ratably over a 10-year period beginning with the year in which the costs are paid or incurred. If taxpayer does not use this method, the excess of the exploration expenditures actually deducted over the amount that would have been deducted if 10 year amortization had been elected is an item of tax preference subject to the alternative minimum tax.

Jan 1, 1985

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968

By S. J. Noesen, J. R. Hughes

Several four-inch-diameter tungsten ingots were arc melted in vacuum or in hydrogen atmospheres. Melting pressures, melt-off rates, effect of atmospheres, and other pertinent factors were examined. Two of these ingots were extruded at 1650°C. Subsequently, forging and rolling were carried out at lower temperatures. For a 60 per cent area reduction by rolling, a one-hour recrystallization temperature of 1250°C was obtained. This temperature is considerably lower than those reported in previously published work, and can probably be attributed to the extreme purity of the as-cast ingots (N, H, 0 all less than 1 ppm). EVER since W. D. Coolidge, in 1909, described his process for producing tungsten metal of high density and good workability via the powder metallurgy tech-

Jan 1, 1961

By George C. Reynolds

INTRODUCTION The overall importance of the minerals industry during the next 20 years was highlighted In "The Global 200 Report to the President" (Barney, 1982) in the following terms: "The industrial and agricultural processes that are taken for granted today would be severely disrupted of any one of dozens of critical minerals ceased to be available in dependable, reasonably priced supply. Supply in turn has become highly energy intensive and international In scope ...... because resources are not uniformly distributed geographically, political considerations (also) become an Important determinant of price and trade patterns." In attempting to determine Australia’s contribution of bauxite raw materials to the world of the future, this paper necessarily also concerns itself with the alumina and aluminium industry to which it supplles the raw material. It is an industry which is energy intensive, International in scope and heavily influenced by political considerations. The aluminium industry has shown a remarkably rapid growth during the past 20 years (Fig. 1).

Jan 1, 1982

By T. H. Alden, H. W. Schadler

The strain rate dependence of the flow stress of the eutectoid Zn-Al alloy has been determined as a function of mechanical processing, microstructure, and temperature. The best superplastic properties result from the ultrafine, equiaxed structure produced by solution treatment and isothermal transformation at 0°C. Lamellar structures produced by isothermal transformation and coarse equiaxed structures produced by annealing also exhibit strain rate sensitivity in excess of 0.5, but at higher stresses and lower strain rates than the finest structure. Solution treatment and isothermal transformation eliminate the effect of prior processing history. Small composition variations in the binary alloy do not influence the mechanical properties. Below the eutectoid transformation temperature (.275C) increasing temperature lowers the flow stress at all strain rates. The data do not favor any of the present proposals for the mechanism of superplastic flow. ALLOYS of zinc and aluminum, near the eutectoid composition, have been investigated for: 1) the flow stress-strain rate and elongation behavior,1, 2) the transformation kinetics,3 and 3) structure,3"5 but the structure sensitivity of the mechanical properties is poorly understood. Using a near eutectoid alloy water-quenched from 380°C, Backofen et aL2 estab- high and increases with increasing strain rate. They found a correlation between strain rate sensitivity and tensile elongation as expected from the increased resistance to necking that a high strain rate sensitivity provides.296 The large elongation at high strain rates is attractive for metal forming. Since most other superplastic alloys7-l3 do not show high strain rate sensitivity at such a high strain rate (for the exception see Ref. 12) there is the possibility of a unique deformation mechanism for this alloy. The sensitivity of the mechanical properties of the eutectoid alloy to thermal history1 suggests a structure sensitivity that has not been demonstrated. Gar-wood and Hopkins3 identified a lamellar product for material transformed between 200" and 260°C. The size of the lamellae decreased with decreasing temperature. They also demonstrated that an unresolved transformation product formed below 200°C. A granular two-phase material was resolved for specimens quenched to below 150°C by Mitbauer and sauerwald4 who observed coarsening of the structure after annealing. The role of grain boundaries in superplastic deformation is suggested by the strong effect of grain refinement in encouraging this phenomenon at high strain rateS7-11, 13 and is emphasized in several proposals about rnechanism7, 8, 12 and in a theory14 of high-temperature deformation. Alden8 showed metallographic evidence that grain boundary sliding is occurring extensively at strain rates where m is large but less at high strain rates where normal plasticity is observed. Holt and Backofen10 have shown that sliding also oc-

Jan 1, 1969

By A. L. Baxley

An Untapped Energy Resource As much as 20 billion cubic feet of natural gas per day are flared from remote oil fields for lack of a commercially viable means of capturing, transporting, and marketing such gas. The magnitude of these gas flares can be put into perspective from an early satellite photograph (Fig. 1) which shows lights from the major cities of Russia and Eastern Europe dwarfed by the natural gas being flared in the Persian Gulf. Together, these wasted resources contain the energy equivalent of about one-half of the gasoline consumption in the United States today (Fig. 2). Additional trillions of cubic feet of natural gas are "shut-in" because of no economically viable means of commercial recovery. Methanol and liquified natural gas (LNG) are the only two practical fuel products which can be produced economically from these gas supplies. Many of these gas supplies are less than 500 million cubic feet of gas per day, making an LNG facility uneconomic. In contrast, barge-mounted methanol plants can economically convert billions of cubic feet of gas per day into safe, clean-burning methanol. The methanol approach offers the only economical route to transform vast, known reserves of natural gas into a highly versatile primary liquid fuel. Methanol Barges: An Innovative Solution The barges will be towed to suitable offshore and upriver locations such as Alaska, South America, Africa, Southeast Asia, Australia, New Zealand, and the South Pacific Islands, as well as fields in the Persian Gulf and Mediterranean Sea. At the offshore production site, a barge will be anchored by a single point mooring buoy that will also serve as an entry point for natural gas feedstock and an offloading point for methanol (Fig. 3). At some sites the barge would be beached. Each barge will produce methanol and store it in internal tanks with a capacity of 18 million gallons. The methanol will be offloaded into conventional tankers and safely transported directly to market. Unlike LNG, methanol requires neither specially built carriers nor specially built receiving terminals. Once a particular gas field has been exhausted, the barge will be towed to another location to continue production. Each barge will measure 320 by 500 ft, approximately the size of four football fields, and will have the capacity to produce 1 million gallons or 2800 metric tons of methanol per day, from approximately 100 million cubic feet of natural gas per day (Fig. 4). The barges will use the highly successful "low- pressure" design developed by the Lurgi Company of Germany, a process proven in land-based methanol plants throughout the world during the last ten years. The decision to use Lurgi technology for "sea-trans- portable" methanol plants was based on the higher efficiency and greater operability of the technology compared to other commercially proven processes. The conversion plant will be designed to accept a wide variety of feed gas compositions, and will produce chemical-grade methanol for the broadest market base (Fig. 5). To minimize costs and construction time, the barge-mounted plants will be built in the high technology environment of a domestic or foreign shipyard. Selection of the construction site for each barge will be dictated by the location of the production site and by the relative construction costs. A number of shipyards have the capacity to build several barges per year. The detailed marine engineering to integrate the design of the processing plant with the floating platform can be performed by numerous major engineering companies around the world. Production Economics The barge-mounted plant concept not only assures large volumes of methanol, but it also keeps the overall production cost low by minimizing construction cost and providing access to low cost natural gas feedstock with no alternative or a negative value. Together, these advantages make the barge-mounted methanol plants economical today. The cost structure of a new barge-mounted methanol plant differs from that of existing methanol producers around the world (Fig. 6). For example, if a U.S. Gulf Coast producer is paying $4.70/MMBtu in 1985 for natural gas, the barge plant could afford to pay about $1.6O/MMBtu for gas and be able to deliver methanol to the Gulf Coast at the same price. At some future date such as 1990, a gas cost of $6.70/MMBtu for a domestic producer would have cost parity with about $3.60/MMBtu gas cost for the barge plant. In many foreign markets, feedstocks other than natural gas are used for methanol production (Fig. 7). For example, most of Japan's capacity is based on LNG while Western Europe uses residual oil or naptha. Because these feedstocks are substantially more ex- pensive than natural gas used by U.S. producers, the barge plants will compete even more favorably in these foreign markets. As crude oil prices rise, the value of methanol in each of these markets will increase. However, the hierarchy of methanol values in these markets should remain unchanged. Furthermore, the cost advantage for using methanol in these markets will improve as world energy costs increase since the value of remote gas should not escalate significantly.

Jan 1, 1982

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur' Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur' Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

IT is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references 1 to 4. Investigations on the properties at elevated temperatures are few, however,5-7 and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. As is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hardening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During [TABLE I.-Sources of Materials Used in the Testing Program MATERIAL ORIGIN AND TREATMENT 24S-T Alclad.... From Lockheed stock. 24S-RT Alclad... Direct from mill. 24S-T80 Alclad.. 24S-O Alclad from Lockheed stock, solution-heat-treated (925°F., water quench) and aged at 375°F. for t0 t % hour. 24S-T8I Alclad.. 24S-T Alclad from Lockheed stock, plant stretched up t0 I per cent and aged t0 ± % hr. at 375°F. 24S-T86 Alclad.. 24S-RT Alclad from Lockheed stock aged 534 ± 34 hr. at 375°F. 6IS-W (bare).... From Lockheed stock. 6IS-T (bare) 6IS-W (bare) from Lockheed stock aged 8 hr. at 350°F. XB7SS-T Alclad. From Lockheed stock.] the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "overaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: I. The higher the temperature, the more rapidly is the fully aged condition attained.

Jan 1, 1945

By J. A. Eisele

The Bureau of Mines has played an important role in the revival of precious-metal mining underway in the Western United States. During the past 30 years, many techniques used by industry to recover gold and silver were pioneered and developed by the Bureau of Mines. In 1952, technology was developed to strip gold from granular activated carbon and allow the carbon to be reused. In 1969, the heap leaching concept was applied to low-grade gold and silver ores and mine wastes. Heap leaching in conjunction with carbon adsorption-desorption permits very low value material to be economically processed. In 1970, an oxidation treatment based on hypochlorite was developed to increase the recovery of gold from carbonaceous gold ores by cyanidation. In the early 19501s, attempts were made to employ carbon-in-pulp technology to recover gold from ores, but the fixed price of gold and increasing operational costs made the process unprofitable. The Bureau of Mines and Homestake Mining Co. jointly operated a carbon-in-pulp pilot plant, and the technology was used in full-scale production at the Homestake Mine in 1972. In 1973, a pressure stripping method, which decreased the time needed for the stripping step, was developed to desorb gold and silver from carbon. An alcohol desorption method, developed in 1976, also decreased the carbon stripping time. These stripping methods are in commercial use. In 1979, an agglomeration pretreatment was developed that permitted clayey precious metal ores to be heap-leached. Agglomeration-heap leaching technology is being used by at least 30 operations, several of them major gold and silver mines. Almost all precious-metal-mining companies use at least one of the above techniques in production facilities.

Jan 1, 1984