Search Documents

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited avail- ability in certain areas. Limestone and dolomite are so useful and so abundant that in 1972 more than 690 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our recent report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1975

By Yinchang Wang

1. INTRODUCTION 1. Subject, and Scope The formation of the oxidized ores of zinc has been recognized as a subject of great importance in economic geology. For many years these ores have been much sought, partly because they are more desirable for metallurgical treatment and partly because they are apt to be freer from gangue than is the sulphide of zinc. Up to very recent years the oxidized ores were the principal source of the metal and at present they still furnish a large portion of the commercial production. . The oxidized ores of zinc include six minerals, as shown in the-following table

Jan 9, 1915

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By John A. Church

IN May, 1878, I had the honor of presenting to the Institute, at the Chattanooga meeting, some observations upon the heat of the Comstock Lode, and since then the subject has attracted some attention and criticism, in the course of which, I have observed errors of apprehension which I beg leave to correct now. Mr. John Arthur Phillips discussed it before the Geological Society, his paper being printed in the Quarterly Journal for August, 1879.* His criticism is based upon that part of my paper in which I quote a number of analyses of the mine waters, to illustrate the fact that the heat does not come from the oxidation of pyrite. I pointed out that these waters contain only an insignificant proportion of sulphuric acid, and not enough to account for even one per cent. Of * A Contribution to the History of Mineral Veins. By J. Arthur Phillips, Esq., F.G.S. Quarterly Journal of the Geological Society for August, 1879.

Jan 1, 1880

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969

By W. J. Moore, E. M. Swiggard, H. Shenker

Beryllium is the most soluble of the double-acceptor impurities in germanium; the solubility is at least 1 x 10 19 atoms cm3. Photoconductive, optical, and electrical measurements were made on a set of Ge:Be samples grown without other intentionally added imp~ivities. The excited-states spectrum of beryllium in germanium was determined both in zero field and in magnetic fields up to 30 kc. It was found that the absorption 0-f lines in the vicinity of the G line increased markedly with increasing magnetic field. The ioniza-tion energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mez: using the excited-states spectrum. An infrared detector using a Ge:Be element was found to have a normalized detectivity D* (50 p, 1000 cps, 1 cps) of 9 X ldO cm-~ps"~-w-'. The Ge:Be sambles exhibited low-field breakdown and inibzirity band conduction effects at low temperatures. WHILE the properties of most dopants in germanium have been thoroughly investigated, the properties of beryllium in germanium have had relatively little attention. Much of the work that has been done' has been concerned with the properties of singly ionized beryllium in germanium. The purpose of the present work was to determine the photoconductive and electrical properties of beryllium-doped germanium (Ge:~e) with a small concentration of other electrically active impurities. Ge:Be is of special interest since beryllium is the most soluble of the known double-acceptor impurities in germanium. MATERIALS PREPARATION A set of &:Be crystals with beryllium concentrations between 5 x 1013 and 1x 10'' cmm3 and without other intentionally added impurities was grown in a hydrogen atmosphere by the horizontal zone-refining techniques described by Swiggard and Shenker.2 The segregation coefficient of beryllium in germanium was found to be about 0.07 and its maximum solubility was found to be greater than 1 x 10'' atoms cm-3 which is in agreement with previous results.' Most of the crystals were found to have a small net concentration of shallow acceptors; for example, a crystal having a beryllium concentration of 1.1 X 1016 cm-3 was found to have a net concentration of shallow acceptors of less than 1.5 X 1013 cm-3. Ingots designed to have a beryllium concentration of 1 x 1017 cm-3 or less exhibited a loss of electrically active beryllium. That is, the beryllium concentration was lower than expected and the decrease of the beryllium concentration along the length of the ingot was much larger than expected. It is hypothesized that this effect is due to the oxidation of the beryllium by the residual oxygen in the system. This effect is similar to but not as severe as the effect observed with boron in germani~m.3, 4 OPTICAL ABSORPTION SPECTRUM The excited-states spectrum of neutral beryllium atoms in germanium was studied by measuring the infrared optical absorption spectrum. A typical spectrum is shown in Fig. 1; the labeling of the absorption lines follows that of Fisher and Fan.* The spacings between the observed lines and the D line are nearly equal to the corresponding spacings for the other ac -ceptors in germanium.5-7 By the use of the theoretical result67' that the neutral impurity ionization energy is 2.53 mev larger than the energy of the D line, the ionization energy of neutral beryllium in germanium was determined to be 24.3 * 0.1 mev at 4.2"K. This method yields a more precise value of the impurity ionization energy than the usual Hall effect method.' The absorption spectrum of Ge:Be was also measured as a function of magnetic field using a magnetic field parallel to the incident radiation and using unpolarized radiation. A typical spectrum taken at 30 kG is shown in Fig. 2. An unexpected observation is that the absorption of the lines in the vicinity of the G line (there is a strong possibility that some of these lines may be associated with lines other than the G line) increases with magnetic field. RESISTIVITY AND HALL DATA Measurements of Hall voltage vs temperature were made on several of the samples. The thermal activa-

Jan 1, 1968

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of trans-ferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 114 miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended oil the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack oil refractories.

Jan 1, 1938

By Wayne T. Brooks

The Occupational Safety and Health Act of 1970, although providing no precise definitions of safe and healthful working conditions, specifies mandatory duties, and methods and procedures -- "to assure so far as possible every working man and woman in the nation safe and healthful working conditions." The dynamics of the workplace ad the dynamics of this coextensive Act both spring from the same source. Both require at any given time an application of the then con- temporaneous highest state of the art. Both are flexible, ongoing, adaptive, changing; both advance by a blending of experience and research.

Jan 1, 1972

By Harlowe Hardinge

THE sound made by ball, pebble and rod mills has long been used by the operator as the "telltale " of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill under the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control. RELATION OF SOUND TO USEFUL GRINDING ENERGY Experience has taught us that there is a difference in character as well as in intensity of sound between a mill grinding wet and one grinding dry, in open or closed circuit, to obtain a coarse or fine product, on the same material, to say nothing of the effect with a variety of different materials. Broadly speaking, a wet-grinding mill operates best at a lower sound level than the same mill grinding dry, with other conditions the same. Several reasons for this variation in sound intensity under these conditions can be advanced, but the important point is that there is a difference, based upon practical results. Since these reasons may be more or less involved, and may be subject to much discussion, only one will be considered here. It is apparent that two balls hitting together or a ball striking the lining, if there is no intervening material, will produce the maximum sound. If a complete cushion of material is placed between the balls or ball and liner, so that the energy is dissipated without doing useful work, the balls will be unable to create enough pressure or force to fracture the particles, and the sound will be at a minimum. At some point in between-that is, where there is sufficient material between the balls or ball and liner so that the ball will fracture the particles without mashing them unduly-the sound

Jan 1, 1939

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By Ward C. Smith

The industry of producing and processing boron compounds is called the borax industry because the chief product is borax, the decahydrate of disodium tetraborate. For the same reason, it is common to speak of borax mining. Reference to borate mining also is common, and while appropriate where it emphasizes the diversity of borate minerals that are mined in various countries, it is rather unsatisfactory where used in a general sense, because it seems to exclude the important production of borax from brine at Searles Lake, California, and of boric acid from steam vents in Tuscany, Italy. The terms "boron industry" and "boron mining" might seem more comprehensive, but are little used, and this is fortunate because they would be misleading-the element boron is manufactured only in small amounts for special uses, and it is not found free in nature. In most occurrences, boron is combined with oxygen and is in a borate or borosilicate material. The history of the modem borax industry starts with the introduction into Europe of borax from Tibet in the 13th century, about the time of Marco Polo, if not actually by him. The discovery that borax has unique value as a flux in metal soldering and ceramic glazing must have been made at some unknown time much earlier. As a rule, any mineral that has been used so long that its early history is lost must occur in deposits that are easily recognized and worked, and this is undoubtedly true of borax in Tibet. According to meager accounts,9 the borax occurs there in arid mountain basins as surficial crusts that coat the ground about thermal springs and seeps of mineralized water, and as coarser crystals in the bottom muds of shallow pools and lakes. Much the same essential features of surface exposures and minerals easy to recognize and recover characterize most of the deposits later found and worked elsewhere. The borax industry at the present time is faced with rising demands for its products, and consequently is increasing its productive capacity and appraising its borate resources.18 The areas that contain the known borate deposits are most likely to yield additional production, hence their distribution in the world is of interest, and is summarized later in this chapter. Mineralogy The mineral raw materials used by the borax industry include various borates mined in several countries, borax extracted from brines at Searles Lake in California, and boric acid extracted from the steam of vents in Tuscany in Italy. The hydrated borates[$] of chief commercial importance are listed in Table 1, which also shows their chemical composition. The properties of only the four most important borates are summarized here, but detailed descriptions of the borates and the minerals commonly found with them can be found in mineralogy textbooks.41 Ulexite generally forms clusters of silky fibers rather than large individual crystals. A

Jan 1, 1960

By C. C. Furnas, T. L. Joseph

It is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investiga-tion1,2 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper. Importance of Gas-solid Contact One of the authors has pointed out in a previous report? that the operation of the blast-furnace process is entirely dependent on contact between the gas stream and the solid particles in the stock. The gas stream carries the necessary heat as well as the carbon monoxide molecules that do the work of rednction. In the parts of the furnace in which there is little or no contact between the gas stream and the solids there can be little work of reduction. Obviously, the part of the apparatus that is not doing the work for which it is intended is inefficient; the ideal condition is one in which all portions of the stock column are

Jan 1, 1929

By C. R. Boyd

WITHOUT attempting to do more than give a preliminary or skeleton report upon the geology and minerals of Southwestern Virginia at this time, I am led to hope that the great commercial importance of the sixty miles of cross-section here crudely treated of

Jan 1, 1877

By M. W. Fabjanczyk, E. G. Alexander

INTRODUCTION The purpose of this paper is to summarise development of design processes used in the 1100 oreoody as a result of experience encountered. Design methods have been developed as a result of the history of ground behaviour, free-standing qualities of cemented back fill and mass blasting techniques. This paper contains an historical review of design methods previously described by Matthews ( 1972 ) , Hornsby and Sullivan (1977 and 19781, Kirkby, Blair and Hutton (19781, and Stewart (1980). The reasoning behind design philosphy changes are discussed and placed into context with methods now adopted. The 1100 orebody is Mount Isa's main producer of copper ore (5 million tonnes per year ) . Proven reserves are 120 million tonnes at 3.2% Cu. Location of the 1100 orebody in relation to overall mine geometry was well described by Dayton (1976). Geology The orebody is located in a series of massive brecciated shale lenses, in either a siliceous or dolomitic matrix, surrounded and separated by a uniform shale sequence. The whole formation is truncated at depth by a faulted contact with a greenschist facies metamorphic sequence below (Figure 1 and Figure 2) Mathias and Clark (1976). The breccia is known locally as silica dolomite and contains nearly all the economic mineralisation. Interfingering of shale and breccia often results in irregular boundaries to the silica dolomite and the ore limits. Geometry The geometry of the orebodies is shown by Figures 1, 2 and 3. Figure 3 also shows the location of the copper orebodies in relation to the lead orebodies. Structure Although the orebody is contained within the massive breccia (u.c.s. 150-250 MPa), it is cut by shear zones sub-parallel to the regional bedding (north-south striking, dipping approximately 60o to the west), and diagonally by major transverse faults (Figure A). These major faults have continuity in excess of 300 metres, with varying amounts of displacement up to 200 metres, and are zones of potential movement.

Jan 1, 1981

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By N. W. Wickersham, Ward B. Blodget, Roberts R. Boyd

The year 1926 has seen few radical changes or developments in methods of drilling and handling oil wells, but it has been a year of steady progress and development in deep drilling and production methods. Probably the outstanding development of the year was recognition by the directors of the American Petroleum Institute of the importance of natural gas in the production of oil, and the Institute directors' resolutions in December, 1926, regarding regulation of gas production with oil by state legislation. This matter is extremely important and will receive the attention of the industry in 1927. Advances in Drilling Equipment The history of the progress of deep well drilling is the solution of problems as they have confronted the operator. As the prospects for deeper production have become apparent, methods of penetrating the earth to greater depths have been devised. Rotary Equipment Improvements in the construction and in the methods of operation of rotary drilling equipment have practically caused elimination of cable tools in California for all but shallow work. The rotary drill, from 1910 when it began to be a practical factor in California, has been making steady advances, first displacing cable tools for drilling to the oil sands in proved fields and later displacing the cable-tool outfit entirely. With the perfection of machinery for taking core samples of the formation penetrated, the rotary drill has become generally used for wildcat work, continuous coring being practiced when desirable. Deep Holes The use of the rotary drill has made commercially feasible the opening of oil fields at greater depths than was considered possible with cable tools. Heavier equipment has been promptly supplied as occasion has

Jan 1, 1927