Search Documents

ALTHOUGH the open-hearth charge contributes CO, C02, H2, A and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required, for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In, any event, this requirement appears. small in comparison with the

Jan 1, 1964

By R. S. Pratt

IT is proposed to discuss the materials and furnaces, as well as the melting procedures used in preparing metal for casting billets, bars or cakes for mill fabrication. As far as possible, consideration will be given to the alloys that are commonly made in most brass mills producing strip, tube, rod and wire. RAW MATERIAL The basic raw material for such mills, of course, is copper, which may be obtained in the form of ingots, ingot bars or cathodes. Refinery-cast ingots and ingot bars, which are simply double ingots, are supplied in accordance with A.S.T.M. Specifications as regular electrolytic or fire-refined tough-pitch copper. In the wrought-metal industry, the electrolytic brands have been preferred, although during the war large quantities of fire-refined coppers sufficiently pure to be suitable for all existing requirements were imported from South America. With the exception of Lake copper, most primary fire refined coppers produced in this country have not been considered satisfactory for wrought metal alloys. Cathode copper, which is now widely used instead of ingot copper for alloying, is the electrolytically deposited metal that is normally remelted in the production of electrolytic tough-pitch ingots. It is in the form of rough, flat plates not suitable for processing but quite satisfactory for melting when sheared into suitable sizes. Raw zinc is perhaps the next most important raw material and this is obtained in various grades, depending on the analytical requirements of the alloy to be made. The grades of zinc as outlined in the A.S.T.M. Specifications vary in cost with the amount of impurities-lead, iron, cadmium-and are purchased in such a way as to produce the most economical mixture consistent with the purity required in the alloy. Other virgin metals (lead, tin, aluminum and nickel) are used in varying quantities for making copper alloys. These elements can also be purchased in accordance with the appropriate A.S.T.M. Specifications where available. Also available are a number of special alloys, which are used as deoxidizers or as means of adding relatively small quantities of elements not suitable for adding directly as virgin metal. In this category are such materials as phosphor copper or phosphor tin, silicon copper, manganese copper, cadmium copper, and copper-iron or zinc-iron alloys. Some of these alloys may be purchased on a definite alloy basis or may be produced in the plant itself for its own use. For largely economic reasons, however, a great proportion of the charge to the melting furnaces consists of alloy scrap. In the production of many finished products, as much as 70 or 75 per cent of the metal originally cast may be discarded at various points along the production line. This material eventually finds its way back to the casting shop as mill scrap, overhaul or scalping chips, skeleton scrap, rod turnings, or miscellaneous fabricating scrap. One of the most serious problems in the

Jan 1, 1946

By F. D. Rosi, F. C. Perkins, L. L. Seigle

An investigation was made of the mechanism of plastic flow in coarse grained specimens of both sponge and iodide titanium at low (-196°C) and high (500° and 800°C) temperatures. Deformation by slip occurs predominantly on a {1011} plane and in a <1120> direction over this entire temperature range, and secondary slip on {101-1} planes becomes more prevalent with overthisentireincreasing temperature.range, The crystallographic habit of the predominant twin planes becomes more prevalent with type is temperature-dependent, and deformation by twinning increases as the temperature of testing is lowered. Kink bands were not observed at -196OC and rarely at the high temperatures. A LTHOUGH the deform a tional mechanisms in . -titanium at atmospheric temperature have been extensively investigated," there is little information regarding the influence of testing temperature on these mechanisms. The only available data come from the recent work by McHargue and Hammond, who extended single crystals of iodide titanium at a temperature of 815°C. No significant changes in the types of slip and twinning planes were observed, but increased activity on the type I, order 1 pyramidal slip planes and on the type 11, order 2 twinning planes was reported. These planes contribute very little to the deformation process at room temperature.&apos;&apos; &apos; Since there is interest in titanium as a material for use at both low and high temperatures, the present investigation was undertaken to examine the slip and twinning behavior in coarse grained specimens of titanium at -—196", 500°, and 800°C in order to determine the general effect of temperature on the mechanism of plastic deformation. Experimental Material Used and Specimen Preparation—Both sponge and iodide titanium were used in the present investigation; chemical analyses appear in Table I. These materials were arc-melted under argon into 25 g slugs, which were then cold-rolled approximately 90 pct to a sheet thickness of 0.05 in. Since the strain-anneal technique was used for obtaining coarse grains, the cold-rolled sheets were made into tensile specimens which were then annealed to produce a relatively coarse uniform grain structure prior to critical straining. The details of the strain-anneal treatment. size of grains, and the method for preparing the specimen surface for optical microscopy have been described in a previous report.&apos; In order to obtain a wider spread in crystal orientation for the present work, it was necessary to vary the rolling schedule to reduce the degree of preferred orientation in the annealed sheets prior to critical straining. Methods for Tensile Testing—The apparatus for experiments at the temperature of liquid nitrogen (—196°C) consisted of two concentric stainless steel

Jan 1, 1957

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble&apos;s results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By E. C. Harder

The situation in the United States, at the present time, regarding the supply of manganese ores and alloys of manganese is one of great seriousness and is likely to become increasingly so while the European war continues. The two principal iron-manganese alloys, ferromanganese and splegel-eisen, are indispensable in steel manufacture, being used extensively in the Bessemer and open-hearth processes. Spiegeleisen, the lower alloy, contains between 15 and 25 per cent., and ferromanganese, the higher alloy, between 60 and 80 per cent., of manganese. Besides manganese the alloys contain iron and carbon. On the market ferromanganese is usually quoted on the basis of 80 per cent. manganese, and spiegeleisen on the basis of 20 per cent. manganese. The consumption of ferromanganese has been increasing during recent years at the expense of spiegeleisen, because larger quantities of the latter must be used to accomplish the same purpose with the result that the amount of carbon introduced with it into the molten metal is frequently injuriously great. Manganese ore proper, in the form of manganese dioxide, is used extensively in many chemical industries, especially for oxidizing purposes. It is also used for the manufacture of both wet and dry electric cells and in the manufacture of paints and dyes. The manganese ore used in this country has been derived hitherto from three principal sources: Southern Russia, Southern British India and East Central Brazil. The following tables show the quantity of manganese ore imported from these countries, and (for comparison) the domestic production, during 1912, 1913 and 1914. The imported manganese ore has been used largely in the manufacture of iron-manganese alloys and in addition large quantities of the alloys themselves have been imported, chiefly from Great Britain, Germany and other European countries.

Jan 1, 1917

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper&apos; reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.&apos; To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By Thomas L. Garwood, F. C. Menk

I T is generally accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uni¬form bed. With a dusty feed the fines tend to segregate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants deducting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets.

Jan 1, 1943

By S. J. M. van Leeuwen, R. Feenstra

The effect of jets on bit penetration has been investigated by means of a 50-ton drilling machine and 8½-in. commercial jet bits, drilling under representative bottom-hole conditions. The conclusions apply to the drilling of impermeable rock only. Penetration rate is in all cases primarily hampered by a differential pressure effect, known as dynamic hold-down. Jet action can reduce this slightly. Major gain in penetration rate, up to 25 or 50 per cent, is already ohtained at medium-high jet power. At high bit load, penetration by soft to medium-hard-formation bits is further hampered by bit-balling. Its alleviation requires intensive tooth scavenging, which is best performed by slanted nozzles with trailing, high-velocity, high-volume jets, hitting bottom in front of the teeth. Penetration may then improve by a 100 per cent. At high bit load, bottom-balling limits the penetration of insert-type bits. In this case bottom scavenging is required, which is most effectively performed with high velocity jets from nozzles extended close to bottom. As a result of this measure, penetration may improve 70 per cent in non-friable rock, and less in friable rock. This will make the insert-type bit more versatile. Toothed hard-formation hits suffer at high bit load from both bit- and bottom-balling. Slanted nozzles, possibly much extended, with high-velocity, high-volume jets then have best prospects. INTRODUCTION For years the use of jet bits in oil well drilling has been increasing, in conjunction with ever greater hydraulic horsepower. To the same extent, the need for efficient use of the horsepower has grown.&apos; This paper, it is hoped, will contribute to an understanding of how effective jet action may be obtained. It deals with the effect of jets on phenomena that are known&apos; " to hamper bit penetration. To study this effect, laboratory drilling tests were performed with 8½-in. commercial bits under bottom-hole pressures representative of deep wells. The investigation has been restricted to the drilling of practically impermeable rock. In the following sections, the increase in bit penetration rates due to jetting is discussed for conditions which made the troublesome phenomena stand out one at a time. A brief definition and interpretation of these phenomena is given in Appendix A. Appendix B gives the results of measurements of fluid velocities along the hole bottom, performed in stationary flow tests. Descriptions of equipment, bits, rocks and mud are collected in Appendix C. Unless otherwise mentioned, drilling conditions were kept standard as given in Table 1. CUTTING TRANSPORT TO THE ANNULUS Jet action was for some time believed to merely improve the transport of cuttings from bottom to annulus, resulting in a clean hole bottom. Flow tests performed in 1954 at the Battelle Memorial Institute6 showed, however, that jet velocities of the order of 40 ft/sec sufficed to clear even large (0.4-in.) chips from bottom in the time between two successive tooth actions. In the field, optimum jet velocities are appreciably higher, indicating that other effects must be involved. This much is confirmed by the results of our drilling experiments in soft rocks performed under atmospheric pressure, i.e., in absence of pressure-differential effects. Fig. 1 shows that variation in the nozzle velocity from 40 to 330 ft/sec had no effect on penetration rate, unless the bit penetrated more than 7 mm per revolution, which is about half the tooth height. At such high rates—150 ft/hr at 100 rpm—cuttings would be caught in the tooth cavities, leading to bit-balling, which was noticed on inspection of the bit. The jets thus assisted in keeping the tooth cavities clean. This is just perceptibly reflected in the penetration-rate curves of Fig. 1: Much the same results were obtained in hard rocks with hard-formation three-cone bits. The conclusion is that transport of loose cuttings towards the annulus does not require a powerful jet action. In the following sections we shall see that in deep-well drilling other phenomena are of greater importance. DYNAMIC HOLD-DOWN It is generally accepted that, in deep-well drilling, bit penetration is hampered primarily by the existence of a difference in pressure between the fluid in the hole and that in the rock at the depth of cutting.2-5 In the drilling

Jan 1, 1965

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough &apos;0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough &apos;0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By M. A. Mosher

Most modern electrolytic copper refineries have found it expedient to build and operate a complete secondaries plant for the treatment of the electrolytic slime accumulated in the cells during the corrosion of the copper anodes. In the earlier years this was done for the sole purpose of promptly recovering in marketable form the silver and gold contained in the slime. Later, improvements in refining methods made possible the recovery of the more precious metals such as platinum, palladium, osmium and iridium, and in recent years, due largely to an increasing market, many secondaries plants have undertaken the commercial production of selenium and tellurium. The complete up-to-date secondaries plant, or silver refinery as it is usually called, is therefore equipped for the production in marketable form of from six to eight metals. The physical plant and operations may be separated into six main divisions: 1. Slime treatment, in which the raw slime is treated by wet methods for the removal of its high copper content and portions of other impurities such as arsenic, selenium and tellurium. 2. Furnace refining, in which the remainder of the base-metal content of the slime is removed by fluxing and fire-refining. 3. Electrolytic parting and refining, in which the silver and gold are parted and obtained in the pure state. 4. Melting of silver and gold into marketable form. 5. Recovery and refining of the more precious metals. 6. Recovery and refining of selenium and tellurium. The Silver Refinery of the Raritan Copper Works at Perth Amboy, N. J., is a complete secondaries plant and the following description of its equipment and processes is, in a general way, typical of other plants of its kind. Slime Treatment The raw slime, pumped with a minimum amount of cell solution from the electrolytic copper refinery, is discharged into the center of circular settling tanks 15 ft. in diameter by 8 ft. deep, where the slime settles out and the solution overflows peripherally to return to the copper refinery by gravity. The slime is then dropped through a bottom outlet to a

Jan 1, 1934

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

Discussion of the paper of COURTENAY DEKALB, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 331 to 337. HORACE V. WINCHELL, Minneapolis, Minn.-Mr. Dehalb summarizes the reasons which he believes are important for the revision of the mining laws, as follows: "1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous." We all appreciate the force of that suggestion. The idea of the old prospector who made rules and regulations in the early days, which were attempted to he incorporated, so far as possible, in the Mining Act of 1872, was that all of the veins in a certain district outcropped upon the surface, or approximately parallel to each other upon the surface, and maintained that parallelism beneath the surface. Therefore, it seemed perfectly proper and natural for each man to stake his claim upon an outcropping, and have the right to follow that vein in working downward, with the general expectation that his workings would always remain just as far away from those of his neighbor as the outcroppings upon the surface. This does not happen to be the case. Dr. Raymond has very ingeniously referred to the subject in one case, in words which read as follows: "If all mining properties presented this beautiful simplicity of structure (ideal location of ideal vein), and all mining locators exhibited a corresponding simplicity of purpose, the application of the law would be easy, but the naiveté of the statute fares badly between the freaks of nature and the tricks of man."

Jan 5, 1915

By D. A. Thomas, E. S. Meieran

Tungsten wires were examined by transmission electron microscopy after drawing and after high-temperature annealing. Drawn wire consists of highly elongated grains called fibers, whose long axis is parallel to [110]. Each fiber is ribbon-shaped, with the wide dimension of the ribbon parallel to (001) and the narrow dimension parallel to (110). Furthermore, most fibers are bent about [I10] and twisted along their length. The fibers are divided into cells, which in some cases contain a platelet substructure lying on (110) planes. The misorien-tations of these platelets accumulate to allow the macroscopic twist of the fibers. During annealing, several competing reactions occur, starting at different temperatures and progressing at different rates. Among these processes are fiber-boz~ndary migration, polygonization, dislocation rearrangement, and possibly impurity segregation. The fiber-boundary migration accompanied by the formation of transverse boundaries during polygonization leads to an equiaxed grain structure although recrystal-lization does not occur. There is a relationship between the flow stress of the wires and their average subgrain width in the form sy = s0 + kyd-1/2 . Also, there appears to be a relatio&apos;nship between wire ductility and the formation of transverse boundaries during annealing at about 800°C. THERE have been many investigations of the structures and properties of tungsten wires1-4 due to their commercial importance for use as lamp filaments. The structural studies have so far been limited to optical microscope and replica electron-microscope studies. due to the difficulty of .-me- paring from wires thin foils which can be examined by transmission electron microscopy. However, this difficulty has been recently overcome,5 and it is now possible to examine tungsten wires by transmission electron microscopy as well as by other techniques. In this paper, the structure of drawn tungsten wire is described, as are the changes in the structure during high-temperature annealing. Some discussion of the relationship between structures and properties is also given. EXPERIMENTAL MATERIALS AND PROCEDURES Commercial 0.030-in.-diam doped tungsten wires drawn at progressively decreasing temperatures between about 1400° and about 800°C were examined. The composition, mechanical properties, and optical microstructures are described in detail elsewhere.&apos; All experimental materials were vacuum-annealed for 10 ot 30 min at temperatures at 100°C intervals between 700° and 2000°C. Specimens were thinned for examination in the Siemens Elmiskop I electron microscope by the method of Meieran and Thomas.5 STRUCTURE OF AS-DRAWN WIRE The optical microstructure of as-drawn tungsten wire has been described by Peck and Thomas.7 They observed that wire in longitudinal section consists of highly elongated grains called fibers whose width varies between 1 and 10 µ, while in transverse section the fibers appear to be elliptical in cross section and bent about their common [110] wire axis. They explained this unusual appearance as being due to the drawing of a bcc material with a [110] texture, and predicted that the wide and narrow planes of the fiber cross section would be parallel to (001) and (110), respectively. The fibers apparently bend about the [110] axis during drawing to maintain grain boundary continuity during drawing. Transmission electron microscopy offers a way of checking these predictions as well as providing a more detailed picture of the wire structure. Figs. 1, 2, and 3 are typical electron micrographs of

Jan 1, 1965

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called&apos; "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex X-ray instrument for the measurement of the ash contents of washed bituminous coal products. The results obtained for selected products from five preparation plants in the northern Appalachian region are described. Emphasis of the study was placed on low-ash bituminous coals suit-able for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by the Cendrex for all the products tested. A principal disadvantage of coal in competition with other fuels has been its inconsistent quality, especially with respect to ash content. Mine rnechanization and production from coalbeds of inferior quality have accentuated this failing. Present quality control methods in coal preparation plants are inadequate because (1) control samples taken over a production shift only serve to give the average quality of the product, (2) conventional sampling and analysis data are usually not available at the time a shipment is scheduled, and (3) the plant operator does not have the use of such data when the coal is being processed so that operating conditions may be adjusted for correcting variations in quality. Thus, the development and use of continuous-control monitoring instruments is of prime importance. The Federal Bureau of Mines arranged to investigate an instrument using x-rays for rapid continuous ash determinations. Developed by the Dutch State Mines and first described in 1958,&apos; this instrument, which has found widespread acceptance in Europe, is designed to provide ash analysis of any desired coal feed or product stream with only a five-minute time lag between sample collection and analytical results. With limit controls, this unit could be used to feed back signals to preset the separating gravity of coal washers, control the ratio of various coals needed to produce an acceptable blend, and permit the sorting of a washed product into two qualities, one which is below and the other which is above a prescribed ash content. This unit can also be used discontinuously for rapid determination of coal samples taken in the usual manner. THEORY Di jkstra and Sieswerda of the Dutch State Mines studied the effect of chemical composition and ash content on the absorption coefficient of coal with the transmitted radiation method.&apos; They found that with an X-ray wavelength of 1.79 A and values calculated for the absorption coefficients of ash and combustibles, the absorption coefficient of coal gave a linear relationship when plotted against the ash content. Thus, a method of measuring the absorption coefficient of coal could also be used to measure the ash content. However, practical attempts to measure the ash content of coal by comparing the intensities of the transmitted X-rays failed. The absorption coefficient of coal can also be obtained by irradiating a layer of coal with x-rays and measuring the intensity of the diffused reflection (backscatter method). The relationship between the diffused reflection and the ash content is actually hyperbolic but approximates a straight line over a narrow range. A measuring circuit that balanced the difference in intensity of the reflected radiation from a standard surface against that from a coal sample was used. By plotting this difference of reflected radiation against the ash content, a curve which approximated a straight line over a range of 8 percentage points of ash was obtained. DESCRIPTION OF EQUIPMENT The apparatus performs two distinct functions: (1) the preparation of the sample to a suitable size consist and moisture content for delivery to the x-ray element, and (2) the measurement of the ash content by the x-ray element. In a continuous operation the coal sample is delivered to a conditioner where it is dried to a maximum of 1% surface moisture and pulverized in a high speed mill to -48-mesh. This material is fed, at a rate of 250-300 gpm onto a rotating disk, shown in Fig. 1, where it is mixed with material already present. The mixture is rotated on the disk and

Jan 1, 1969

Jan 1, 1940

Jan 1, 1941