Search Documents

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 1, 1919

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;1 and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. ? The general precipitation occurs at a

Jan 1, 1938

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919

TULSA, the host of the Petroleum Division this year, is the oil metropolis of the Mid- Continent and gateway of the Southwest. It has risen in less than three decades from a dusty cattle town of less than 1000 population to its present-day status of a modern, wide-awake and prosperous city of close to 150,000, with an assessed realty valuation of approximately $100,000,000. Oil was discovered near Tulsa in 1901, and with it came th.2 development of the Mid-Continent field, one of the richest in the world. Tulsa from the start has been the center of operations, and its location on foul- and aggressive application of the airplane to oil-field requirements tends to fix this status as production is developed farther and farther afield. That Tulsa is far more than an ephemeral oil town is punched into the newcomer's- especially the Easterner's-mind, as he is whisked by taxi from the railroad station to the Hotel Mayo. The cicadalike pounding of the riveters on the steel skeletons of many skyscrapers, mounting upward to fill the gaps in an already well-developed skyline, dispels the feeling of a new atmosphere and puts him back on Forty-second Street, Michigan Boulevard or whatever his own particular "Main Street" may be along which an American city is being remade. Practically every company of any importance operating in the Mid-Con-

Jan 1, 1928

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces' has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

Dr. Wadsworth's discussion of leaching is straightforward and certainly points out some of the critical areas in regards to the fundamental aspects of leaching. I will address myself to the more practical aspects of leaching. As a couple of general comments, very fine particles are often dealt with only when necessary. In many processing applications the sands and slimes are separated with the sand portion being treated by common metallurgical techniques and the slime portion being treated essentially by any technology that will recover some of the values. Ore treatment techniques such as leach/precipitate/float (LPF) have been used in the copper industry to take advantage of leachable copper preferentially reporting to the fine fraction. The second advantage, of course, is the improved metallurgy associated with the treatment of the sand fraction. Cases can be made for sand/slime separations in the aluminum and uranium industry where most of the value reports to the slime fraction and the sand fraction is rejected In the agitated leach systems, fine particles are often the most readily attacked and leached. In dump, vat and in-situ leaching, fine particles cause considerable problems. The fines will tend to restrict the solution flow from portions of the leach feed. This either causes a significantly reduced solution flow or, more probably, the solution will channel, by-passing much of the ore. In either case the result is a decreased metal recovery from ore. The fine particles of principal concern are clays of a flat plate-like shape which can very effectively compact, swell and cause a decreased solution flow. Discrete silica grains or sulfide grains due to their shape, even though they may be very fine, will not cause nearly the problems clays and secondary precipitates can cause.

Jan 1, 1979

By F. C. Newton

RefineRs of lead by the Parkes process have always been solicitous of recovering the zinc used in the desilverization, and justly so, as the loss in zinc constitutes one of the heavy costs in this method of refining. Part of this loss is due to the absorption of zinc by lead, and in the present state of knowledge is not recoverable as metallic zinc. The remainder of the zinc, which finds its way into the precious-metal-bearing crust, is recoverable and naturally engages the operators' most exacting attention. Careful elimination of the impurities in base bullion has enabled the refiner to produce a zinc crust better adapted to retorting, which reflects favorably in the zinc recovery;- and to produce a richer crust, thereby lowering the zineking cost, as the increased efficiency of the zinc results in less of it being in circulation. It is obvious that if the ratio of concentration be increased, a lessening of the amount of crust formed will ensue, throwing less work on the retorts and diminishing the amount of retort metal sent to the cupels, thus making an actual money saving in all these operations. In the effort to obtain a rich crust, the metallurgist has increased the heat to a considerable degree, upon the assumption that at the higher temperature the zinc-dver alloy could be squeezed free from the adhering lead. A further possibility for improvement suggested itself in the freezing-point curve of Prof. H. C. Carpenter, upon zinc and silver. Study of this curve disclosed the existence of a definite chemical compound, Zn3Ag2, with a freezing point of 665" C., a promising compound for practical application. In the experiment undertaken it was endeavored to force this compound into the crust, hoping thereby to obtain a higher concentration than formerly. It was recognized that in bringing a large kettle of lead to such a heat, more fuel would be used, the life of the kettle would perhaps be shorter, and other disadvantages would be experienced. AS a commercial operation, the project would have to stand on its own feet,

Jan 1, 1915

By J. R. Lewis, J. H. Hamilton, V. D. Hanson, K. W. Heinlein, J. M.194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By J. H. Hamilton, J. R. Lewis, K. W. Heinlein, V. D. Hanson, J. M. 194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By J. M. Callow

THe results obtained by pneumatic flotation throughout the country on all classes of ore, and the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practicc. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cyeloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by Dr. Rudolf Gahl on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. CoMPABATIVE SENSITIVENESS AND ATTENDANCE Concerning the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that, with the exception of about 24 days at the end of the testing period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the concIusions drawn on page 499 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 1, 1917

By John C. Martin

The discovery of a new gas reservoir demands that the planning of a sottnd well-spacing program be initiated early in the development stage. It is the purpose of this discussion to illustrate by actual field examples the application of basic well-spacing principles, previously developed for oil reservoirs, to the problem of well spacing in natural gas fields. These studies are presented for the field use of geologists and engineers who are concerned with the initial planning of the proper development of the newly discovered gas reservoir. INTRODUCTION The phenomenal growth of a vigorous natural gas industry emphasizes the increasing importance of natural gas as a source of energy, fuel, and raw materials to our nation's economy. Since 1945 marketed production of natural gas for the U. S. has increased 21/2 times to a record high of 10.6 trillion cu ft during 1957. As major participants in the gas industry, we share an added interest to develop and produce our natural gas reserves with constantly improved efficiency. The subject of well spacing is vitally important to the gas industry, for the well itself plays a significant role in the development of the natural gas reservoir and in control of the recovery process. Maximum utilization of wells is an integral part of sound conservation practices. The discovery of a new gas reservoir demands that careful choice of well location and well spacing be made and that the planning of a sound well spacing program be initiated early an the development stage. With the drilling of the first development well, efforts of the geologist and engineer must be directed toward acquisition of adequate technical evidence upon which a firm recommendation for a spacing program may be based. With this technical appraisal as a foundation, operators and state regulatory agencies jointly can go far in providing a framework for sound development of gas fields to achieve a program of conservation that avoids the unnecessary well. WELL-SPACING CONCEPTS Through laboratory and field investigations of the mechanism of the recovery of oil and gas, of fluid behavior, and of effective control of reservoir and well, a crystallization of ideas regarding reservoir behavior has emerged as a well-developed technology. Associated with a better understanding of the fundamental principles underlying reservoir and well behavior has been the growth of concepts concerning the role of wells and their spacing in the development and operation of an oil or gas reservoir. In addition to serving as outlets for the withdrawal of fluids from the reservoir, wells are recognized as having two other important functions: (1) providing access to the reservoir to obtain information concerning the characteristics of the reservoir and its fluids, and (2) serving as a means by which the natural or induced recovery mechanism may be effectively controlled. Beyond a minimum number of wells required to fulfill these two functions, additional wells will not increase recovery. With particular emphasis upon well spacing in oil reservoirs, many studies of the well spacing-recovery relationship have evolved the concept that the ultimate oil recovery is essentially independent of the well spacing.' These fundamental concepts are no different when regarding the role of wells and their spacing in the natural gas reservoir. They are equally applicable to the consideration of well spacing in gas reservoirs. For the gas reservoir, the problem of well spacing then revolves around the question of drainage and the degree or extent to which a well may drain gas from its surrounding reservoir environment. Theoretical and Experimental Work During the past 30 years, theoretical and experimental work carried on to study the physical principles involved in the flow of fluids through porous media has shed light upon the matter of drainage. Fundamental mathematical equations have been derived to describe the mechanism of flow of oil and gas through porous rocks. With the recent advent of high-speed digital computers, attempts have been made with mounting success to develop solutions, employing numerical techniques, to mathematical expressions that describe more rigorously the physical behavior and mechanism involved in the unsteady-state flow of compressible fluids, such as a gas, through porous rock. In 1953, Bruce, Peace-man, Rachford and Ricez published a stable numerical procedure for solving the equation for production of gas at constant rate. The results of these calculations are significant with respect to this matter of drainage, for they indicated (1) that depletion of the gas reservoir resulted in a drop in pressure at the extremity of the

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By Walter Rose, W. A. Bruce

Improved apparatus, methods, and experimental techniques for determining the capillary pressure-saturation relation are described in detail. In this connection a new multi-core procedure has been developed which simplifies the experimental work in the study of relatively homogeneous reservoirs. The basic theory concerning the Leverett capillary pressure function has been extended and has been given some practical application. Some discussion is presented to indicate the relationship of relative permeability to capillary pressure, and to provide a new description of capillary pressure phenomena by introducing the concept of the psi function. INTRODUCTION For the purposes of this paper the capillary character of a porous medium will be defined to express the basic properties of the system, which produce observed results of fluid behavior. These basic properties may be classified in the following manner, according to their relationship to: (a) The geometrical configuration of the interstitial spaces. This involves consideration of the packing of the particles, producing points of grain contact, and variations in pore size distribution. The packing itself is often modified by the secondary processes of mineralization which introduces factors of cementation, and of solution action which causes alteration of pore structure. (b) The physical and chemical nature of the interstitial surfaces. This involves consideration of the presence of interstitial clay coatings, the existence of non-uniform wetting surfaces; or, more generally, a consideration of the tendency towards variable interaction between the interstitial surfaces and the fluid phases saturating the interstitial spaces. (c) The physical and chemical properties of the fluid phases in contact with the interstitial surfaces. This involves consideration of the factors of surface, interfacial and adhesion tensions; contact angles; viscosity; density difference between immiscible fluid phases; and other fluid properties. Fine grained, granular, porous materials such as found in petroleum reser~oir rock possess characteristics which are expressible by (1) permeability, (2) porosity, and (3) the capillary pressure-saturation behavior of immiscible fluids in this medium. These three measurable macroscopic properties depend upon the microscopic properties enumerated above in a manner which defines the capillary character. Systems of capillary tubes or regularly packed spheres may be thought of as ideal and numerous references can be cited in which exact mathematical formulations are developed to show the relationships governing the static distribution and dynamic motion of fluids in their interstitial spaces. The capillary character of non-ideal porous systems such as reservoir rock also is basic in determining the behavior of fluids contained therein; although, in general, the connection is not mathematically derivable but must be approached through indirect experimental measurement. This paper gives consideration to the evaluation of petroleum reservoir rock capillary character. The methods employed may be applied to the solution of problems in other fields, and the conclusions reached should contribute to the basic capillary theory of any porous system containing fluid phases. In this paper, a modification of the core analysis method of capillary pressure is employed and it is intended to show that the capillary character of reservoir rock can be expressed in terms of experimental quantities. A very general method of interpretation correlating the capillary pressure tests with fundamental characteristics such as rock texture, surface areas, permeability, occasionally clay content and cementation is introduced. Eventually an attempt is made for establishing a method of deriving relative permeability to the wetting phase from capillary pressure data. The experimental evaluation of capillary character must be approached in a statistical manner if reservoir properties are to be inferred from data on small cores. This is implied by the heterogeneous character of most petroleum reservoirs, and suggests that considerable intelligence should be applied in core sampling. Finally, this paper supports the view that once the capillary character of a given type of reservoir rock has been established by core analysis, fluid behavior can then be inferred in other similar rock. Although no great progress has been made in establishing what variation can be tolerated without altering the basic fluid behavior properties, evidence will be presented to indicate that certain reservoir formations are sufficiently homogenous with respect to capillary character that the data obtained on one core will be useful in predicting the properties of other cores of similar origin. Tests have shown that cores under consideration can vary widely with respect to porosity and permeability and still be considered similar in capillary character. EXPERIMENTAL METHODS AND TECHNIQUES Various types of displacement cell apparatus for capillary pressure experiments have been described in the literature. Bruce and Welge; Thornton and Marshall; McCullough, Albaugh and Jones3; Hassler and Brunner; Lever-

Jan 1, 1949

By Walter Rose, W. A. Bruce

Improved apparatus, methods, and experimental techniques for determining the capillary pressure-saturation relation are described in detail. In this connection a new multi-core procedure has been developed which simplifies the experimental work in the study of relatively homogeneous reservoirs. The basic theory concerning the Leverett capillary pressure function has been extended and has been given some practical application. Some discussion is presented to indicate the relationship of relative permeability to capillary pressure, and to provide a new description of capillary pressure phenomena by introducing the concept of the psi function. INTRODUCTION For the purposes of this paper the capillary character of a porous medium will be defined to express the basic properties of the system, which produce observed results of fluid behavior. These basic properties may be classified in the following manner, according to their relationship to: (a) The geometrical configuration of the interstitial spaces. This involves consideration of the packing of the particles, producing points of grain contact, and variations in pore size distribution. The packing itself is often modified by the secondary processes of mineralization which introduces factors of cementation, and of solution action which causes alteration of pore structure. (b) The physical and chemical nature of the interstitial surfaces. This involves consideration of the presence of interstitial clay coatings, the existence of non-uniform wetting surfaces; or, more generally, a consideration of the tendency towards variable interaction between the interstitial surfaces and the fluid phases saturating the interstitial spaces. (c) The physical and chemical properties of the fluid phases in contact with the interstitial surfaces. This involves consideration of the factors of surface, interfacial and adhesion tensions; contact angles; viscosity; density difference between immiscible fluid phases; and other fluid properties. Fine grained, granular, porous materials such as found in petroleum reser~oir rock possess characteristics which are expressible by (1) permeability, (2) porosity, and (3) the capillary pressure-saturation behavior of immiscible fluids in this medium. These three measurable macroscopic properties depend upon the microscopic properties enumerated above in a manner which defines the capillary character. Systems of capillary tubes or regularly packed spheres may be thought of as ideal and numerous references can be cited in which exact mathematical formulations are developed to show the relationships governing the static distribution and dynamic motion of fluids in their interstitial spaces. The capillary character of non-ideal porous systems such as reservoir rock also is basic in determining the behavior of fluids contained therein; although, in general, the connection is not mathematically derivable but must be approached through indirect experimental measurement. This paper gives consideration to the evaluation of petroleum reservoir rock capillary character. The methods employed may be applied to the solution of problems in other fields, and the conclusions reached should contribute to the basic capillary theory of any porous system containing fluid phases. In this paper, a modification of the core analysis method of capillary pressure is employed and it is intended to show that the capillary character of reservoir rock can be expressed in terms of experimental quantities. A very general method of interpretation correlating the capillary pressure tests with fundamental characteristics such as rock texture, surface areas, permeability, occasionally clay content and cementation is introduced. Eventually an attempt is made for establishing a method of deriving relative permeability to the wetting phase from capillary pressure data. The experimental evaluation of capillary character must be approached in a statistical manner if reservoir properties are to be inferred from data on small cores. This is implied by the heterogeneous character of most petroleum reservoirs, and suggests that considerable intelligence should be applied in core sampling. Finally, this paper supports the view that once the capillary character of a given type of reservoir rock has been established by core analysis, fluid behavior can then be inferred in other similar rock. Although no great progress has been made in establishing what variation can be tolerated without altering the basic fluid behavior properties, evidence will be presented to indicate that certain reservoir formations are sufficiently homogenous with respect to capillary character that the data obtained on one core will be useful in predicting the properties of other cores of similar origin. Tests have shown that cores under consideration can vary widely with respect to porosity and permeability and still be considered similar in capillary character. EXPERIMENTAL METHODS AND TECHNIQUES Various types of displacement cell apparatus for capillary pressure experiments have been described in the literature. Bruce and Welge; Thornton and Marshall; McCullough, Albaugh and Jones3; Hassler and Brunner; Lever-

Jan 1, 1949

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By H. C. Fiedler

A high degree of cuhe-on-edge grain orientation and good magnetic properties were obtained in Si-Fe strip processed from laboratory heats containing vanadium nitride inclusions. The higher the nitrogen content the greater was the restraint on normal grain growth and the greater was the ability to undergo secondary recrystal-lization. The degree of restraint in a heat containing magnanese sulfide inclusions was slightly greater than that in the lowest nitrogen vanadium nitride heat. The high rate of diffusion of nitrogen in the temperature range in which the texture is developed makes it necessary to retard the loss of the inclusions until the texture has been developed. MAY and Turnbulll have shown that to develop the cube-on-edge secondary recrystallization texture in Si-Fe it is necessary that inclusions, such as manganese sulfide, be present to prevent normal grain growth. They showed that the driving force for the growth of the secondary grains is inversely proportional to the diameter of the matrix grains, and that the function of the inclusions is to maintain a small matrix grain size. Fast3has developed cube-on- edge texture in Si-Fe by nitriding the hot rolled band. The silicon nitride thereby formed promotes secondary recrystallization during the anneal of the final gage strip. To obtain the best magnetic properties, the inclusions must be removed from the strip after the grain orientation has been developed. Nitride inclusions have an inherent advantage over sulfide inclusions in that the greater diffusivity of nitrogen as comared to sulfur permits the use of shorter times and or lower temperatures for the purification heat treatment. The purpose of the work to be described was to examine the usefulness of vanadium nitride inclusions in developing the cube-on-edge texture and to determine the magnetic properties of oriented strip made from heats containing these inclusions. A comparison is made with a heat having had iden-

Jan 1, 1962

By Benj. F. Tillson

To most mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount of drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be SO handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau of Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 1, 1922