Search Documents

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) IN vol. 33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will be made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1878

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By Frank Clemes Smith

In describing a certain class of ores, of ever-increasing importance in the Black Hills, they are variously called " refractory,)' "siliceous," or Potsdam;" the first name serving to distinguish them from the other important class—the free mill-

Jan 1, 1898

By W. B. Devereux

The special mriditions under which gold occurs in the Potsdam formation of the Black Hills prew~lt features worthy of a more systematic pesentation than they have heretofore received. The notes

Jan 1, 1882

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By William R. Webster

At the Richmond mecting in February, 1901, I presented for discussion the proposed rail-specifications of Committee No. 1 of the American Section of the International Association for Testing Materials, with a review of their work, and other matters relating to the heat-treatment and chemical composition of steel (Trans., xxxi., 455). In order to bring out the views of our members on the important points referred to, I offered for discussion the following questions and comments (trans., xxxi., 972): " 1. The advantages to be gained by using more metal in the flanges and web of the heavier sections of rails.

Jan 1, 1903

By Jean L. Leroy

The Lead Smelting works of Metallurgie Hoboken S.A. are located on the banks of the river Scheldt a few miles South of Antwerp. Lead refining began at Hoboken in 1687, when it was restricted mainly to desilverizing lead bullion from Central America. Since then, various changes have been made to develop the works into a comprehensive and integrated custom smelter and refinery. Multiple hearth roasting furnaces, down-draft sinter machines and blast furnaces of standard design are used for the treatment of "complex" lead ores and secondary materials. A lead refinery based on the Harris process, with Parkes desilverizing followed by vacuum dezincing and Kroll Betterton debismuthizing was commissioned in 1967. Facilities for the recovery of precious metals, bismuth, antimony, arsenic and sulfuric acid are available. Special problems arise from the presence of large quantities of copper in the materials treated.

Jan 1, 1970

By J. Wright, R. J. Tyler

Abstract-Changes in the pore structure of hematite pellets during reduction to iron were investigated under a variety of experimental conditions. Pore structures were determined by a mercury penetration technique. The reduction temperature was found to be the major influence on structure, the pore system being bimodal below 750°C and unimodal above 900°C. Pore sizes ranging from 0.04 to 20 [um] were observed in completely metallized pellets produced over the temperature range 650-1050°C. Gas composition and reduction rates also influenced the pore structure of the metallized pellets, although to a lesser extent than the reduction temperature. An apparent activation energy of 24 kcal/mole was derived for the pore formation ptocess.

Jan 8, 1978

By Fred Wise

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed, The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxi-dized, The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices, On this basis metallurgical results are viewed in the light of an optimum tailing rather than a per-centage of extraction.

Jan 1, 1940

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By Carl Henrich

Jan 1, 1890

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By R. R. Sayers

TWO serious hazards from coal dust confront the bituminous-coal miner- -a physical or safety hazard and a physiological or health hazard. The first threatens the miner with loss of life from coal-dint explosions, and the second with loss of health and earning capacity from inhaling large quantities of the dust. Studies by the Bureau of Mines have shown that coal dust, except some grades of anthracite dust, is capable of initiating an explosion when no explosive gas is present and that its property of extending or propagating an explosion has been responsible for nearly all the widespread explosions that have occurred in bituminous mines in the United States in the present century. For years many mining people believed that low-volatile coal dust was not explosive but not only is it explosive but if the source of ignition is intense, it is as explosive as the dust of many high-volatile coals because the war is creating increased pressure for greater coal production and because of the trend toward greater mechanization in mines, explosion and health hazards from coal dust are likely !n increase considerably.

Jan 1, 1943

By William G. Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the nonhomogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of deforming beyond the limit of purely elastic strains, a plasticity theory is required. The purpose of this chapter is to present a plasticity theory for anisotropic rocks and soils. The proposed theory is based on the work of Hill in anisotropic metal plasticity and represents an extension of his work so as to include anisotropic geologic materials. The point of departure from metal plasticity theory begins with the inclusion of the normal stresses as linear terms in the yield condition, which plays a central role in plasticity. Once the yield condition is established, the plastic strain increments are obtained immediately through the principle of normality. For practical applications, some simplification of the three-dimensional theory is re-

Jan 1, 1972

F. WEIMER,* Washington, D. C. (written discussiont).-For electrical measuring instruments, especially those types that involve the Wheat-stone bridge or potentiometer principle and standards of electrical resist-ance, there has been, for a considerable time, a need for better resistance materials. For a satisfactory resistance material, much depends on the purposes for which it is to be used. For potentiometers and Wheatstone bridges, such as are in more or less general use, and the more common forms of resistance standards, a good quality of manganin answers fairly well. However, it should not be presumed that manganin is considered ideal for the purpose, for in measuring instruments and resistance stand-ards, there is still much to be desired. An experience of more than 10 years in the study of the resistance standards and resistance apparatus shows that manganin resistances change with time in a way that is very annoying and the maintenance of the unit of resistance to the desired accuracy requires an excessive amount of work or may be said to be prac-tically impossible. The changes in resistance are generally most rapid and erratic in resistances of very low and very high values. In resist-ances of low value, the resistance material is often in the form of thin sheets so that the surface is large and usually more or less unprotected from the atmosphere, or the oil in. the case of oil-immersed standards. In resistances of high value, the resistance material is in the form of fine wire and, therefore, the surface is large compared with the cross-section. In resistances of medium value, the surface is less, compared with the cross-section, or better protected, usually by a silk wrapping impregnated with shellac. This suggests that one of the difficulties with manganin is slow surface action or oxidation, even when an effort has been made to protect the surface from such action However, the changes observed cannot all be accounted for on this basis. There are, presumably, also some internal changes in the resistance material even when it has been annealed. Further; the changes in manganin resistances seem to be more or less independent of its electrical properties. In other respects, too, manganin is not ideal.

Jan 11, 1919

By C. W. Purington

Jan 1, 1900

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953