Search Documents

By Walter Stern

The self-potential or spontaneous polarization method is one of the oldest in the field of electrical exploration. When applied in prospecting for ore bodies, it is one of the most rapid and inexpensive means of locating indications of ore bodies at shallow depth. Usually, the procedure is to survey the equipotential lines of the electrical field that is generated by the electrochemical activity of the ore near the ground-water level, and to localize the so-called negative centers or points of greatest negative anomaly. Another field procedure involves the measurement of potential differences along potential profiles, generally laid out at right angles to the assumed strike. Again, in such survey, the basis for establishing the presence of ore is the location of negative potential anomalies. The earlier writers on the subject, notably Schlumbergerl and R. C. Wells,2 did much to clarify the fundamental electrochemical phenomena involved. Interpretation of the field data, however, remained largely qualitative. In 1925, A. Petrovsky3 analyzed the relation between the shape of the potential anomaly curve and size and depth of an Ore body by assuming the subsurface body to be a polarized sphere.' Along similar lines of approach, Edge and Laby5 considered the ore body a dipping sheet with limited extent in the direction of strike, while Poldini6 based the theory on the assumption of a dipping bar. The following study endeavors to enlarge upon these earlier investigations and attempts, on the basis of the potential distribution of a polarized bar, to indicate certain characteristics of the anomaly curve that make possible the determination of depth, size and dip of a subsurface body. The Spontaneous Polarization Field Set Up by an Ore Body If a sulphide ore body is subjected to oxidation varying in degree in its upper and lower parts according to the difference in the concentration of oxygen within the surrounding medium, an electrical potential field is set up. The form and distribution of this field will be investigated herein with special reference to its components on the earth,s surface. Under the simplifying assumption that the ore body may be considered as a dipole with the point sources Q1 and Q2 situated at its upper and lower ends (Fig. I), the potential of the spontaneous polarization at point P is given by the following equation:

Jan 1, 1946

By M. A. Olade

Biotite, magnetite and quartz feldspar separates from rocks around porphyry copper deposits in the Highland Valley have been analyzed for copper, zinc and other related trace and major elements. Results show high copper concentrations in mineral samples close to mineralization, with a strong positive correlation with whole-rock copper contents. Zinc, on the other hand, shows no cleat-cut systematic relationship to mineralization, although there is a subtle decrease in the dues obtained for anomalous biotite samples. Manganese, cobalt and nickel in biotites show similar patterns as zinc. Using a sulfide-selective leach, it is show that the enhanced copper dues in mineral samples proximate to mineralization can be accounted for by the presence of minute inclusions of sulfides. In contrast zinc seems to occur in isomorphous substitution for femic elements, in a form that is leachable by hydrothermal activity. Results also show that copper content of biotite has a positive correlation with the modal proportion of biotites and their iron contents, whereas a negative relationship with manganese is apparent Geochemical contrast for copper between background and anomaly is not better in mineral fractions than whole rocks, consequently the use of minerals as sampling media shows no obvious advantage for mineral exploration purposes in the Highland Valley district.

Jan 9, 1979

By J. C. Wilhoit, E. M. Galle

A three-dimensional photoelastic study was made to determine the stress state around the wall and bottom of a wellbore due to fluid pressure within the wellbore and unequal principal geostatic stresses. Models simulating the wellbore were made from a phthalic anhydride-cured epoxy resin. The frozen stress technique of three-dimensional photoelastic-ity was used to determine the stresses within the model. Two separate problems were solved: (1) hydrostatic pressure on all sides of the model with the exception of the inside of the hole, and (2) uniaxial compression perpendicular to the center line of the hole. The results are presented in the form of contour curves for each stress component. The curves cover a region which extends several hole radii from the bottom and wall of the hole. By proper use of these results, the state of stress may be calculated for any point on the wall or bottom of the hole, as well as for any point within the material that surrounds the hole. A systematic method is given for calculating these stress components for any combination of fluid pressure within the wellbore and system of unequal principal geostatic stresses, provided one of the principal geostatic stresses is parallel with the wellbore. The results show that stresses around the wall and bottom of a wellbore, induced by an uneyual system of principal geostatic stresses, are appreciably different from those induced by geostatic stresses that are hydrostatic. For uneyual principal geostatic stresses, the experimentally determined stresses on the wall of the hole several radii from the bottom are in good agreement with the stresses calculated by elastic theory. INTRODUCTION Interest in the problem of determining the stresses around and near the bottom of a wellbore, due to geostatic loading and fluid pressure within the wellbore, originated in the petroleum industry. The stresses on the wall of the wellbore are of interest due to their relation to lost circulation during drilling, the fracturing of formations during squeeze cementing and hydraulic fracturing of producing formations. The stresses on the bottom of the hole are of interest to the drilling segment of the industry because to produce a hole in the earth it is necessary to remove material from the bottom of the hole. This removal of material is produced by structural failure of the rock, whatever the criterion for failure may be. Cunningham and Eeninkl have shown that for certain conditions the effect on drilling rate of the bottom-hole stresses caused by a hydrostatic overburden pressure is small compared to other effects. This question, however, needs further experimental and analytical investigation. Much information concerning the stresses on the walls of wellbores has been published considering both equal and unequal principal geostatic stresses. The problem of determining the stresses around the bottom of the wellbore is considerably more complicated. However, previous investigators have obtained numerical and experimental solutions to the problem for equal principal geostatic stresses. whitworth2 and woods3 have obtained numerical solutions. word415 obtained a three-dimensional photoelastic solution, Durelli and Deily 6 obtained surface stresses only by photoelastic means, and Cheatham and Wilhoit7 determined the stresses around the bottom of a short cylindrical cavity. While Miles and McGuire, Harrison and Kieschnick and Hubbert and Willis 10 obtained the stresses on the wall of a wellbore for unequal principal geostatic stresses, they did not concern themselves with the stresses near the bottom of the hole. The estimates made by Hubbert and Willis of the differences between the principal geostatic stresses indicate that, to obtain a satisfactory solution for the stresses around the bottom of a wellbore, unequal principal geostatic stresses should be considered. This work is directed toward obtaining such a solution. The materials in the earth's crust are nonhomo-geneous, permeable and anisotropic. Previous

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By A. A. Venghiattis

This paper is discussed not because of its intrinsic value but because it has been related by its authors to the oilwell gun perforators. It is well known that conditions almost ever present in oilwell perforations are the overburden and the presence of the casing. Because of the lack of information in the paper on the dimensions or confinement of the target rocks, one is led to guess that they were not confined at all and, particularly, that no steel front plates were used on the impact face of the rocks to materialize the presence of the cemented casing. This situation, plus the fact that small steel balls have been used as projectiles instead of actual bullets, makes the whole thing unapplicable to oilwell perforation. When shooting is performed against target rocks confined (as shown on Fig. 1) in such a way as to give a fair image of the overburden applied to the formation to be perforated, as well as of the cemented casing, the following are found. 1. There is no cratering worthy of mention, even with bullets having 10 times higher impact energy per unit projected area than the steel balls mentioned in the article. This has been confirmed with sandstone as well as with other rocks (granite, limestone and chalk). See Figs. 2 and 3. 2. Penetrations vary closely as the logarithm of the impact velocity. On this matter I have established the relation

By A. M. Hall

Sulphur, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.l,2 It may act either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monelt and Inconel are an important group. These sulphides were investi- gated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monel and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. Method of Investigation Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallo-graph equipped with a combination polar -izing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By A. M. Hall

Sulphur, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.l,2 It may act either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monelt and Inconel are an important group. These sulphides were investi- gated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monel and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. Method of Investigation Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallo-graph equipped with a combination polar -izing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By Robert Glass Cleland

BECAUSE of the country's vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country's prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By J. B. Novak

The program describes preventive maintenance practices and controls applicable in situations where maintenance actions are triggered primarily by breakdown or part failure and specification and documentation of detailed maintenance practices are minimal or nonexistent. The presentation describes requirements of organization structure, program administration, implementation and operation, type of benefits expected, and actual benefits derived in selected areas. The principle objectives of the program are to provide quick, inexpensive, and effective controls over maintenance practices and requirements and to establish a nucleus of controls that subsequently can be expanded to cover all maintenance activities.

Jan 1, 1973

By R. Stefanko, Y. J. Wang, H. R. Hardy, R. Y. Kim

Since 1964, the Dept. of Mining at The Pennsylvania State University has been carrying out extensive studies associated with the phenomena of microseismic activity and inelastic behavior in geologic materials. Briefly, the program to date has involved the following stages 1) Study of the microseismic noise and energy rates for selected geologic materials under incremental, uniaxial tension.1,2 2) Investigation of the frequency spectra of microseismic activity of selected geologic materials under incremental, uniaxial tension.3,4 3) Investigation of the time-dependent inelastic deformation of geologic materials and the analysis of such deformation in terms of mechanical models.5, 6 4) Simultaneous study of microseismic activity and time-dependent inelastic deformation in geologic materials under incremental, uniaxial compression.7,8 Details of the research involved in stage 4 of the program constitute the subject of this chapter. It should be noted that the majority of the experimental data quoted in this chapter forms part of a thesis to be presented by one of the authors (Kim) in partial fulfillment of the requirements for the Ph.D. degree in mining engineering at The Pennsylvania State University. During the last two or three years, a number of important papers have been published which deal primarily with the fundamental structure and mechanical behavior of geologic materials. Recent papers 9,10 have provided research workers in the rock mechanics field with a meaningful overall picture of rock as a structural material. The concept that many

Jan 1, 1970

By Richard H. Jahns

Such minerals as beryl, lepidolite, sheet muscovite, spodumene, and tantalite-columbite are obtained chiefly from pegmatite bodies that are internally zoned. As shown by examples of such pegmatites from the Southwestern and Southeastern States during World War II, studies of their internal and external structure have value in prospecting and the planning of exploration, development, and mining.

Jan 1, 1951

By W. H. Wamsley

Used in combination with conveyor belt haulage, bucket wheel excavators offer unusual possibilities for low excavation and haulage costs. Originating in Germany, these machines are now in use or on order for Australia, Northern Rhodesia, the Belgian Congo, Italy, Yugoslavia, France, Belgium, Indonesia, and the Union of South Africa. A diamond mine in South Africa that has been using German bucket wheel excavators since 1928 purchased American cable-way excavators and American scraping equipment after the war. Operating cost for this equipment was double that for the bucket wheel machines operating in the same mines with crawler-mounted stackers. Machines built and operated in the U. S. are, as far as the writer knows, confined to the northern Illinois coal field, where they are used in conjunction with large shovels to strip overburden too high to be reached by the 30 to 40-yd shovels. Their long stacker belts can deposit the spoil far enough behind the coal face to avoid slides, in such a manner as to make reclaiming the land easier. These large, specialized machines are now being made by Bucyrus-Erie Co. but are not adaptable to many open pit mining situations.

Dec 1, 1956

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley' in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By F. R. Conley, D. A. Shock

Solution Mining or In Situ Mining has received increasing attention in the past few years because the method offers many attractive possibilities in improving the environmental impact of mining as well as making feasible the extraction of deeper, low value mineral reserves. This paper will present a brief discussion of the state-of- the-art in total solution, slurry removal and leach mining. As a specific example of utilizing the method, the uranium deposits of South Texas are a type of deposit which have been considered as being amenable to in situ leach mining. The parameters required to ascertain the amenability of such a deposit for in situ leaching will be presented. The hydrological factors which influence the production of the soluble uranium solutions and their displacement will be discussed. Mathematical models for various well configurations have been made and graphic representation will be presented to illustrate various production methods and the resultant hydrological consequences.

Jan 1, 1974

Continued discussion of the paper of R. W. Raymond, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 70, October, 1912, pp. 1111 to 1122. See also discussion printed in Bulletin No. 74, February, 1913, pp. 319 to 329. R. B. BRINSMADE, Puebla, Puebla., Mexico (communication to the Secretary *) :-Though I heartily approve of several minor points emphasized by Dr. Raymond (such as the general desirability of local administration, rather than Federal, and the evils inseparable from the Federal Apex Law), I feel obliged to dissent from his four final propositions. As Dr. G. 0. Smith has already discussed these propositions from the standpoint of the experience of other countries, I shall base my criticism upon certain general economic principles, which will be grouped under the following five topics: 1. The dual theory of property. 2. The essential factors in fixing prices. 3. The relation of land ownership to the distribution of wealth. 4. The relation of land ownership to speculation and development. 5. The relation of land ownership to the political power. I shall give here only a brief outline of these topics, as they are fully treated in the standard treatises on political economy.1

Jan 5, 1913

By M. E. Wadsworth

"For his creative efforts in explaining the electrochemistry of sulfide mineral leaching systems." Leaching reactions that occur during the dissolution of selected base metal sulfides and metals are considered in terms of surface reactions and the influence of intermediate or final products formed. These products may be solid layers, requiring solid phase diffusion for the reaction to proceed, or ions in solution that can influence the kinetics by controlling the mixed potential of the solid. Three general types of reactions are proposed to explain observed rates of reaction. Examples are presented for non-oxidative and oxidative leaching of galena (PbS), anodic dissolution and oxidative leaching of molybdenite (MoS2) and cyanidation of silver and gold.

Jan 1, 1986

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955