Search Documents

By L. E. Wilsey, W. G. Bearden

This paper presents results of analysis of the effect of fracturing on initial flow rates and on ultimate recoveries from low capacity oil formations. This analysis shows that even in formations of permeability as low as 0.1 md, large fracture treatments can yield oil recoveries and production rates approaching those of high permeability formations. Field production information is shown which supports the analytical work. INTRODUCTION Often hydrocarbon bearing formations are discovered which, while they are known to contain large quantities of oil, will not produce at commercially attractive rates without special well stimulation. Attempts to solve this problem led to the development of such techniques as underreaming, shooting, acidizing, and recently hydraulic fracturing. These methods of stimulation have been highly successful in many fields. All of these treatments, however, affect only the pay section near the well bore and therefore owe their success to circumventing and overcoming local permeability reduction about the well bore. It has been the belief that in treating wells to stimulate production in which there is no permeability reduction near the well, the maximum possible production rate increase would be of the order of two or fourfold. Hence, it has been concluded that fracture treatment of uniformly low capacity (permeability times thickness) formations could meet with but limited success. It is the purpose of this paper to show that the use of fracture treatments much larger than usually used can yield commercially attractive producing rates and high recoveries even in formations of permeability less than 0.1 of a md. PROCEDURE In order to illustrate the effects of fracturing, an analytical study of some hypothetical systems was made in which one factor at a time was varied to show what is important in recovering oil from fractured wells. It was assumed that a horizontal fracture of relatively high fluid-carrying capacity extended from a well bore. The presence of such a fracture will cause a marked influence on the flow pattern and pressure distribution in the formations, with the net effect being to reduce tremendously the resistance to flow into the well bore. A diagram of the resulting flow pattern and pressure distribution is illustrated in Fig. 1. Immediately after production commences, the principal flow of fluid is vertically from the formation flanking the fracture, into the fracture, and then into the well. After sufficient oil and gas have been produced to lower the pressure in the formation adjacent the fracture, oil and gas will begin to flow in a radial manner into the fracture from the formations beyond the end of the fracture. In calculating the performance under such conditions. the material balance or conservation of matter equation and equations of flow were solved simultaneously by a stepwise method of calculation. Flow rates were found by determining the pressure distribution, as illustrated

Jan 1, 1955

By Thomas Cox

The following compilations are made from a series of investigations and are used to present the subject in an unbiased manner, as the writer does not represent any company or financial interest. The present situation is complex. The producers are hard pressed by reason of the low price of crude, while the independent refiner is little better off, because of the corresponding cut in price of refined products, except on occasional contracts. If the real costs are analyzed, it will be seen that the land speculators and the lessors—royalty owners—make the larger profits and not the struggling legitimate operator or independent refiner. The present-day (October, 1922) posted prices per barrel for crudes are Kansas, Oklahoma, Mexia, Gulf Coast, and Louisiana..... $1.25 Healdton............................................. 0.75 Northern Texas and Central Texas...................... 1 . 50 Pennsylvania......................................... 3.00 Wyoming, Elk Basin.................................. 1.25 Wyoming, Salt Creek................................ 0.70 California Base..................................... 0.60 These prices are at the well. In addition, crudes must be gathered and transported to refinery (by pipe line or tank cars), refined, and the refined products marketed. These crudes are of various gravities, ranging within a narrow margin for each field or district, so that averages are not difficult to deduce, and it is these averages that really determine the average operating conditions. In order to show the present realizations, the prices and costs now obtaining are listed against the average yields; the figures are also adjusted VOL. urn.----71

Jan 1, 1923

By Thomas Cox

The following compilations are made from a series of investigations and are used to present the subject in an unbiased manner, as the writer does not represent any company or financial interest. The present situation is complex. The producers are hard pressed by reason of the low price of crude, while the independent refiner is little better off, because of the corresponding cut in price of refined products, except on occasional contracts. If the real costs are analyzed, it will be seen that the land speculators and the lessors—royalty owners—make the larger profits and not the struggling legitimate operator or independent refiner. The present-day (October, 1922) posted prices per barrel for crudes are Kansas, Oklahoma, Mexia, Gulf Coast, and Louisiana..... $1.25 Healdton............................................. 0.75 Northern Texas and Central Texas...................... 1 . 50 Pennsylvania......................................... 3.00 Wyoming, Elk Basin.................................. 1.25 Wyoming, Salt Creek................................ 0.70 California Base..................................... 0.60 These prices are at the well. In addition, crudes must be gathered and transported to refinery (by pipe line or tank cars), refined, and the refined products marketed. These crudes are of various gravities, ranging within a narrow margin for each field or district, so that averages are not difficult to deduce, and it is these averages that really determine the average operating conditions. In order to show the present realizations, the prices and costs now obtaining are listed against the average yields; the figures are also adjusted VOL. urn.----71

Jan 1, 1923

By G. W. Sheary

At Bethlehem's Grace mine's 6000-tpd pelletizing plant a cascade control system is utilized to approach a constant magnetite filter cake moisture, a critical factor in obtaining quality green pellets. Variables being controlled by instrumentation are filter feed solids, filter tub level, first and second stage pump sump levels and thickener sludge level, all at varying feed rates. Startup difficulties, modifications and contemplated additions to obtain closer control of the moisture are discussed. Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Co. 's Beth-lehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with %-in. slotted vibrating screens. The ore is washed and screened in the mill and the 1/4-in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30-in. cyclones, to 1% on 100 mesh and 65% -325 mesh. The ground ore is magnetically concentrated by three-drum permanent-type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50-ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% +'1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica. It has been the usual practice to maintain constant filter tank level by pumping an excess constant volume and using a moveable fishtail splitter to divert the desired amount of slurry to the filter tank. The excess from the fishtail and from the filter overflow pipe, which maintains a constant level, is returned to the source. At the Grace mill, tremolite builds up in the pipelines when pumping heavy magnetite concentrate slurries, making it necessary to use polyvinyl

Jan 1, 1962

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By Wilbur A. Nelson

In 1839, Gerard Troost,1 the first State Geologist of Tennessee, reported the occurrence of zinc ores in east Tennessee, in connection with the iron ores at Embreeville; in 1844,2 he refers to the zinc deposits of east Tennessee, especially the apparently rich deposits occurring in Jefferson and Claiborne Counties, while his ninth annual report 3 s a description of the zinc deposits of Jefferson County and a description of the most improved processes by which zinc is extracted from its ores. Yet, only during the last few years have these ores been successfully worked. As far as can be learned, prior to the systematic development of the Mascot district in 1911, no large-scale or successful operation of any of the zinc deposits was carried on. But in that year, after several companies had made considerable progress in developing the Mascot area and had proved a relatively extensive body of low-grade sulfide ore, the American Zinc Co. entered the field. It introduced modern methods of prospecting and mining and from the first was successful. Too great credit cannot be given this company for its pioneer work in a previously unimportant field. Throughout the history of its operations, the American Zinc Co. has confined its efforts to underground mining of the sulfide ore, sphalerite. This company has found that successful results in zinc mining in east Tennessee can be achieved only by expending large sums in prospecting and blocking out bodies of pay ore in sufficient magnitude for large-scale operations. At Mascot are located the mines of the American Zinc Co. of Tennessee, the mines being situated along the Southern Railway in the Ilolston River Valley, Knox County, about 13 miles northeast of Knox-ville. At first only open pits, which were worked for oxidized ores, were operated and the production was small. In 1900, the Roseberry Zinc Co. was organized and sank to a depth of 187 ft. what is now known as No. 3 shaft of the American Zinc Co. The upper 30 ft. was in residual clay,

Jan 1, 1925

By G. J. Wilson

Difficulties experienced in correlating vertical and lateral locations of subsurface features that are encountered in directional wells prompted critical review of the tangential method of computing directional surveys. Inherent discrepancies were indicated to cause small incremental but significantly large cumulative errors in computed vertical depth and horizontal departure. A radius of curvature method, developed for planning and analyzing directional wells, was studied as a means of more accurately calculating survey data. Errors incurred in the tangential method were not present in the radius of curvature method. Conflicting assumptions in calculating dog-leg severity by the tangential method were resolved by a new procedure that was derived from the radius of curvature method. Results of the investigation showed the radius of curvature method to be an improved method for computing directional surveys. Introduction Many improvements in directional drilling tools and techniques have been made in the past 10 years,' but the method of computing survey data has remained virtually unchanged. While use of computers greatly aids the process of calculation' and eliminates many human errors, manual and computer calculations are still made with the assumption that the wellbore consists of straight-line segments. This paper points out discrepancies in the method and presents an improved method in which the wellbore is assumed to be curved. Tangential Method The method presently used to calculate vertical depth, horizontal departure and direction coordinates with measured values of well depth, inclination angle and direction angle is termed the tangential method. This term stems from performing calculations with a series of straight-line segments, with each segment assumed to be tangent to the wellbore at a corresponding survey point. A segment is defined by inclination and direction angles measured at only the lower or deeper end. Consequently, a discrepancy or error is introduced for each segment. Errors are not of extreme magnitude, but cumulatively are significant due to the need to define as accurately as possible the vertical and lateral location of subsurface features such as pay tops, fluid contacts and fault cuts encountered in expensive directional well bores. In Fig. 1, the curved-line segment ab represents a portion of the actual borehole as viewed in the vertical plane. Points a and b are survey stations and +, is the inclination angle at point b. The curved-line segment ab is assumed to be the straight-line segment arb of a length equal to ab and tangent at point b to the curved-line segment. Lengths a'c' and c'b are equal to a'b cos +, and a'b sin +,, respectively. Point a already has been fixed by calcillations performed with survey data obtained at point a, and calculated lengths m'c' and c'b are projected as lengths from point a, rather than from point a'. Point b1 is thus fixed and assumed to represent the actual point b. Calculated length ac" is shorter than actual length ac, and calculated length c"bl is longer than actual length cb. Since b1 is the point from which the next deeper segment will be projected, errors are cumulative. Cumulative error continues to increase as long as the inclination angle continues to increase. When the inclination angle decreases (Fig. 2), calculated length ac" is longer than actual length ac, and calculated length c"bl is shorter than actual length cb. These errors also are cumulative, but differences between calculated and actual lengths are opposite in mathematical sign to differences demonstrated in

Jan 1, 1969

By Richard H. Willey

EFFICIENT handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. BINGHAM CANYON MINE The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been metamorphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling and blasting of the porphyry apparently becomes easier as depth is attained, but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. PAST METHODS At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1947

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By Rodney G. Ravenscroft

Leasing is not a new phenomenon. Experts have identified its origins as early as biblical times. It is a method of finance that has grown rapidly and is now used in most countries, including those of South East Asia, South America, the Middle East and even the People's Republic of China. Internationally, the leasing world divides fairly easily into two groups and this is determined, by and large, according to whether a country has Anglo-Saxon origins or not. Most of the Anglo-Saxon countries have seen tax-oriented leasing become a sophisticated means of financing the acquisition of large and costly items of equipment and large projects. Countries such as France, Spain and Japan have a highly developed leasing industry but it is not tax-oriented. This paper will not address leasing of this kind. LEASING - THE CONCEPT Wide acceptance of leasing as an alternative for financing capital equipment has grown with the recognition by the users of equipment that it is use and not ownership that generates profits. Whilst this seems obvious, memories of repossession of assets during the Depression and attitudes towards leasing as "last resort financing" have raised strong philosophical resistance that has only recently begun to be overturned. A financial lease is a commitment by way of contract between a user of equipment (lessee) and a financial owner (lessor) under which the lessee makes a series of payments in return for use of the equipment. The lessee is acquiring economic value associated with ownership but not ownership of the equipment itself - that remains with the lessor. A lease is a method of financing the use of an asset; other methods finance the assets themselves. It is the taxation aspects that then become important. The lessee is giving up some or all of the taxation benefits of ownership such as depreciation and investment tax credits. The lessor claims these benefits, as he is entitled to do as owner, and takes them into consideration when determining the level of lease payments that are necessary to generate his required rate of return. These lease payments are, of course, lower than they would have been without those taxation benefits. The lease payments themselves are fully tax deductible. This is tax shelter leasing. The lessor is acquiring taxation deductions that are applied fully and immediately against his other taxable income so as to reduce the amount of tax he is to pay to the revenue authorities. It is this concept that makes financial leasing work. Governments provide incentives by way of tax concessions to encourage capital investment. Governments presume that prudent capital investment will offer employment opportunities, generate sales and streamline economic activity. These, in turn, will lead to the collection of government revenue. It makes no difference at all whether these incentives are claimed by a commercial or industrial owner/user or by a financial owner who makes equipment available for use by industry. Rather, the issue is to ensure that if an incentive is available, it is used so as to achieve its desired results. No greater or lesser incentive is available for leasing and leasing does not misuse the taxation aspects of equipment ownership. The critical issue is whether the full value

Jan 1, 1985

By C. Kolm, E. P. Warekois, S. A. Kulin

MUCH insight has been gained into the nature of the cold-worked state of metals in recent years through the use of modern X-ray techniques. These methods have revealed the existence of stacking faults together with regions of high internal strain and have provided means of measuring the atomic perturbations in plastically deformed metals. In view of the recent increased interest in the solid state, it is desirable to extend these techniques to the study of lattice imperfections introduced into semiconductors during plastic deformation. It is of particular interest to compare the state of imperfection sustained by metallic bonding with that sustained by the covalent bonding found in semiconductors. A knowledge of the imperfections which can exist in semiconductors is important from both a theoretical and a practical point of view since they can greatly influence many of the physical properties. In order to determine the possible existence of stacking faults in covalently bonded structures, precise measurements were made of the diffracted peak positions of plastically deformed germanium, gallium antimonide, and indium antimonide. These measurements were based on the theoretical treatment of Paterson1 and are similar to those employed by Warren and warekois2 in their studies of deformed a brass. In addition, diffraction peak profiles were measured on the annealed and plastically deformed materials in order to obtain information concerning the distribution of internal strains through the use of the Fourier methods developed by Warren and Averbach.3 EXPERIMENTAL PROCEDURES AND TECHNIQUES Because of the room-temperature brittleness of the semiconductors studied, it was necessary to plastically deform the materials at elevated temperatures. The brittle-ductile transition temperature ranges of GaSb and InSb are sufficiently low to permit hot-filing operations. Therefore, high-purity, polycrystalline GaSb and InSb were filed in an argon atmosphere at 400' and 300°C, respec-

Jan 1, 1959

By C. E. Wethered

THE Morning mine is operated through one main working adit, known as No. 6 or 800 tunnel level. At a distance of 10,000 ft. underground from the portal is the vertical four-compartment, main working shaft, which extends to the 3050 level, a distance of 2250 ft. below the collar, or 800 level. Shaft-stations are cut and levels opened every 200 ft. of depth and the ore is stoped to the next level above. The vein is nearly vertical and the ore is usually fairly massive and brittle. Both walls are soft and slabby and much difficulty is therefore experienced in holding them. Stopes are usually carried up in short sections, approximately 200 ft. in length, that are mined as rapidly as possible in order to avoid a too great replacement or repair of stope timbers. The four-compartment vertical shaft, 110 ft. in the footwall of the vein, is the sole medium of outlet for all ore mined below the adit level. Two compartments of this shaft are used exclusively for hoisting ore, except at the time of changing shifts, when one compartment is used to handle some of the men and timber. The third compartment is equipped for handling men, tim-ber and all general supplies and is operated by a Nord-berg 300-hp. electric hoist. This hoist has a lifting ca-pacity of 14,000 lb. with an average rope speed of 800 ft. per minute. The fourth compartment is used solely as a manway and pipeway.

Jan 7, 1927

By Charles Camsell

MORE than one-third of all Canada is embraced in the federal domain known as the Northwest Territories. Its most northern point, Cape Columbia, on Ellesmere Island, is only 500 mi. from the Pole. It includes parts of the main physiographic divisions of the North American continent. In the West there is a strip of 30.000 sq. mi. lying in the Cordilleran region, where peaks in the Mackenzie Mountains rise as high as 8500 ft. East of this strip and extending roughly to a line through Great Bear and Great Slave lakes to the Arctic coast is a section of the interior plains. This section, known as the Mackenzie Lowlands, contains the great artery, the most striking feature of the Northwest Territories-the Mackenzie and Slave river waterway impressive in its width, almost two miles in places, and in it's navigability for 1357 miles without obstruction to the sea. Adjoining the Mackenzie Lowlands on the East is the greater portion of the mainland of the Territories, which, as well as a large share of the island area, is in the Canadian Shield.

Jan 1, 1937

Mining examinations are of several kinds and the scope of the investigation depends in each case upon the purpose for which the examination is made. A formal examination of a developed mine is an expensive undertaking; from one to several months are allowed for the work according to the size of the property; many samples are taken; investigation is made of the geological features, including, perhaps, a topographical and geological survey of the surface; the metallurgical treatment of the ore is studied; finally, a determination of costs is demanded. Formal examinations are made for prospective purchasers or as a basis for the consolidation of several properties, and occasionally, in the owner's behalf, to verify the work of resident engineers, or to determine the readiness of a mine for equipment and the kind and capacity of equipment it shall receive. A formal examination of a mine should not be undertaken until a preliminary examination has shown that it is justified. It is regrettable that some engineers are in the habit of prosecuting long and exhaustive examinations of properties whose lack of merit should be, and perhaps is, apparent from the start, or of continuing their investigation long after an unfavorable result is seen to be inevitable. This wasting of a client's money is a species of trickery difficult to prove, and therefore the more contemptible. Preliminary examinations are precisely what the term implies, and are undertaken to determine the advisability of making

Jan 1, 1932

By J. O. Brittain, E. P. Lautenschlager, D. A. Kiewit

Compression tests were run in the temperature range of 700° to 900°C ox 0' phase NiAl intermetal-lic alloys of several grain sizes. At these temperatures the minimum strengths were observed at the stoichiometric composition. While significant increases in strength occurved in both the low-nickel (vacancy) and high-nickel (substitutional) regions, the highest strengths were found in the high-nickel region. During deformation serrated flow was sometimes observed in the low-nickel alloys. After deformation transgranular cvacking and deformation striations were observed in all compositions tested. AS part of a general investigation of the properties of NiAl inter metallic compounds, a preliminary study of the role of point defects upon plasticity was made by high-temperature compression tests on ß' NiAl specimens of several grain sizes and compositions. ß' NiAl is an intermetallic compound having a CsCl structure and a rather wide range of composition from A1-45 at. pct to 60 at. pct Ni.1 According to Bradley and Taylor2 and to cooper,' it possesses a defect lattice in which departures from stoichiometry in the direction of decreased nickel content lead to the presence of vacant nickel sites (although Cooper's work indicates that a small amount of substitution also occurs) whereas departures on the high-nickel side lead to substitution of nickel on aluminum sites. NiAl forms congru-ently from the melt at approximately 1650°C,1 and thus has a higher melting point than either of its component elements. Up to this time, although this and other high-melting intermetallic compounds have been suggested for elevated-temperature usage,4 only the hardness4 and a few tensile-strength measurements5 have been reported for NiAl at high temperatures. In the present investigation the effects of composition upon the compressive-strength properties in a range of 700° to 900°C have been measured for NiAl of several grain sizes. EXPERIMENTAL PROCEDURES The alloys were made as described elsewhere6 from an A1-46.8 at. pct Ni master alloy furnished by the International Nickel Co. with additions of high-purity nickel and aluminum. The charges were vacuum-induction-melted in A12O3 crucibles with small amounts of helium added to the atmosphere to suppress vaporization. They were cooled slowly from the melting temperature to achieve uniform grain size. In order to refine the as-grown grain size a special rolling technique was developed. Alloys were packed into 0.10-in. wall-type 302 stainless-steel tubes which were partially filled with magnesium oxide to prevent bonding between the alloy and the steel jacket. The ends of the tubes were closed by hot forging, and the packets were then hot-rolled. The alloys with greater than 50 at. pct Ni were rolled at 1100°C, but it was found necessary to increase the temperature to 1350° C before alloys with less than 50 at. pct Ni would roll without cracking. With these temperatures, reductions as high as 48 pct were achieved in a single pass. The rolled alloys will hereafter be referred to as "fine grained" whereas the as-grown material will be designated "coarse-grained''. The compression specimens were made by cutting square cross-sectional pieces, approximately 3/16 by 3/16 by 1/2 in., with a water-cooled diamond cut-off wheel from the as-grown or the rolled alloys. Specimens were ground to their final dimensions by polishing through 3/0 grit silicon carbide papers. The final shape was a rectangular parallelepiped of square cross section having a height-to-width ratio of 3:1. Compression testing was carried out in a compression rig of our own design mounted on an In-stron Floor Model. The specimen chamber could be heated to 1000°C and was controlled within ±2°C. The compression rig was enclosed within a bell jar and was maintained at a 50 µ of mercury vacuum throughout the duration of the test. The test cham -ber was heated from room to test temperature within 15 min. Specimens were then held at the test temperature 30 min prior to testing. Previous experiments indicated that no grain growth would occur within this time. An Instron Variable Crosshead speed unit was used to adjust for small variations in specimen lengths in order to have a constant initial strain rate, €, for all specimens of a group. For the fine-grained specimens the strain rate was changed rapidly at constant temperature by a factor of 10 with the speed lever on the Instron. For a given € the compression data was analyzed in terms of true plastic strain (E) and true compressive stress (0).

Jan 1, 1965

By J. T. Jones, H. V. Winchell

In the history of mining in this country there has been nothing exactly similar to the Mesabi iron-range in Minnesota, and the conditions there prevalent. Soft-ore mines are found in many parts of the country. In some the deposits are vertical, and are worked in open pits, or have been so worked, until it was found cheaper to go under ground. In other localities, the ore is scattered through clay beds in the form of hard lumps. These clay beds are sometimes excavated in open pits, and the ore separated by washing. On the Mesabi, the ore itself occurs in strata, and these strata appear quite flat to one standing upon the ground. The ore is soft in the main, and does not require much sorting to free it from foreign or deleterious substances. It is usually covered by the glacial drift-mantle, but occasionally passes beneath a capping of jasperoid rock called " taconite." The ore is twice or three times the thickness of the layer of drift lying upon it. This drift consists of clay, sand, and gravel, with occasional beds of large boulders. There is great difference of opinion among competent miners as to the cheapest methods of mining this ore. It is admitted that local conditions will govern largely ; but there is such a similarity among many of the mines that it seems possible to arrive at some general conclusions on the subject. A typical example of a Mesabi mine is found in the Biwabik. It is one of the largest, and is the most advanced in development. Not a single ton of ore has yet been shipped from this mine, but the expense of the explorations upon which the following description is based has exceeded $60,000. It is seldom that such accurate and complete exploration of a deposit of this magnitude has been possible in the space of time which has elapsed since the discovery of this ore-body. It lies in a new. region, and was remote from railroads until last August, yet, not only the width and length but the depth and quality of the ore-deposit have been learned, and the probable expense of' mining its 20,000,000 tons of ore has been closely figured. After careful consideration, the method of stripping and

Jan 1, 1893

By William E. Newman

The smelting of galena in the ore hearth has been practiced in many countries for several hundred years with varying success. In the United States, the water-jacketed American hearths and the Jumbb hearths have found some favor in the Missouri lead belt, where large quantities of non-argentiferous galena concentrates are produced. In form and method of operation the ore hearth has changed but little since its earliest conception. A detailed description of the furnace is lot needed here; it has been fully described in most works on the metallurgy of lead and in many technical papers. Since its field is restricted to non-argentiferous galena, containing over 68 per cent. of lead, its use is limited to a few districts; and, on account of certain disadvantages attending its operation, modern sintering and blast-furnace practice has nearly driven it out of the Missouri field. It is not generally known that the cost of producing pig lead is smaller by the hearth method than by sintering and blast-furnace smelting. Yet it is doubtful if any metallurgist knowing this to be true would recommend an American hearth installation—by reason of the disadvantages which will be briefly enumerated. The furnace has been limited to a length of from 4 to 5 ft., requiring for its operation two men working an 8-hr. shift as a maximum. The product per man is small; the work is hot and laborious; and the difficulty of completely removing the dust and fume has made it a notorious source of lead poisoning, Although suitable for operations on a small scale a large number of hearths would be required for a plant smelting 10,000 tons of 68 to 70 per cent. concentrates per month; and the number of semi-skilled laborers would be six times the number of hearths—a condition which is prohibitive. On account of the high percentage of dust and fume produced, a large flue and bag-house installation is required and, in the past, the handling and re-treatment of this dust and fume has -been a serious problem.

Jan 1, 1916

By Will H. Coghill, Fred D. DeVaney, R. G. O’Meara

The size of ball mills in the ore-dressing industry has increased from about 4 ft. in each dimension to 10.5 ft. in diameter by 8 ft. in length. In the cement industry they are as long as 45 ft. Plainly the trend has been toward larger mills. The common belief is that the big mills economize in floor space and first cost, but the advantage with respect to friction has not been clearly defined. In the ball-mill studies at Rolla, Mo., laboratory mills as small as 2 by 2 ft. have been found as efficient in terms of the amount of grinding per unit of net power as mills 6 by 4 or 6 by 12 ft. Therefore, if supremacy can be claimed for the big mills, advantage must come from other sources. The advantage to be considered here is reduced loss by friction or dead load. In the study to determine whether big mills have relatively less loss by friction the commercial catalogs were used for fundamental figures. The dimensions and weights of Table 1 are taken from the catalogs (the last line gives data on a Rolla laboratory mill). The net power—that is, the power expended within the mill for grinding—is calculated by a new formula.' The assumed speeds are each at 70 per cent of their theoretical critical speeds, and the mills are loaded to the center with balls. In other words, they are assumed to be working under analogous conditions and are set for good grinding. In the last column the ratio B: A shows that the larger commercial mills are lighter per unit of net power than the smaller mills, and more of the motor output should therefore go into grinding. The laboratory mill seems to have some advantage over the larger mills; it would be expected to be light because it has no liners.

Jan 1, 1935