Search Documents

By William J. Harris, Morris Cohen

INTRODUCTION THE recent application of lineal analysis1,2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at [M.] and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as "a lowering of [M.], resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (Th) for a sufficient period of time, more austenite may be retained at a given lower or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th, is measured explicitly in terms of the excess austenite [(S)] that exists in the steel at Tr, over and above the amount that is normally present after direct quenching to Tr. Tr is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (Th) may be above or below [M], and still cause stabilization depending upon the chemistry of the austenite. Stabilization has been found to occur in the presence of bainite4 and of martensite5,6,7,8 as well as in the absence of either.9 The phenomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at Th that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subsequent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6.8 low alloy 6.7.8 and high alloy tool steels.10,5 Starting with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1948

By William E. Ford, Edward Salisbury Dana

IN the representation of crystals by figures it is customary to draw their edges as if they were projected upon some definite plane. Two sorts of projection are use8; the ah- graphic in which the lines of projection fell at right angles and the chirographic where they fall at oblique angles upon the plane of projection. The second of these projections is the more important, and must be tr2atcd here in some detail. Two points are to be noted in regard to it. In the first place, in the drawings of crystals the point of view is supposed to be at an infinite distance, and it follows from this that all lines which are parallel on the crystal appear parallel in the drawing. In the second place, in all ordinary cases, it is the complete ideal crystal which is represented, that is, the crystal with its full geometrical symmetry as explained on pp. 10 to 13 (cf. note on p. 13). In general, drawings of crystals are made, either by constructing the figure upon a projection of its crystal axes, using the intercepts of the different faces upon the axes in order to determine the directions of the edges or by constructing the figure from the gnomonic (or stereographic) projection of the crystal forms. Both of these methods have their advantages and disadvantages. By drawing the crystal figure by the aid of a projection of its crystal axes the symmetry of the crystal and the relations of its faces to the axes are emphasized. In many cases, however, drawing from a projection of the poles of the crystal faces is simpler and takes less time. The student should be able to use both methods and consequently both are described below.

Jan 1, 1922

By Irwin Roman

IN studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two components ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. General considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note I). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth's field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude Io with vertical component Vo and horizontal component H,. Six station points along a traverse' across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the' disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1946

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

By William E. Ford, Edward Salisbury Dana

239, Contact-Gwiorneters. - The interfacial angles of crystals are measured by means of instruments which are called goniometers. The simplest form is the contact- or hand-goniometer one form of which is represented in Fig. 377. This contact-goniometer consists of a card on which is printed a semi- circular arc graduated to half degrees at the center of which is fastened a celluloid arm which may be turned to any desired position. The method of use of the goniometer is illustrated in Fig. 377. The bottom of the card and

Jan 1, 1922

By A. L. Field

WOOLSEY McA. JOHNSON, Hartford, Conn. (written discussion).¬When ;we regard the number of British thermal units running into the billions that-must be applied to metallurgical slags in the United States, we cannot but conclude that the physical chemistry of-slags is a very important subject when measured in dollars and cents. A further contemplation of the subject shows us that it has been hitherto treated in too purely a practical manner. It is needless to comment at length on the cost of these heat units and on the cost of fluxes to produce these metallurgical slags, for, it amounts to tens of millions of dollars annually. Accordingly, this research is of value to the country. But we must,all balance our results against our efforts. Therefore, while the speaker is unwilling to criticise unduly this meritorious research, lie does criticise it in the interest of the profession for the reason that it seems to him too highly theoretical. The article is much too, scientific to produce results at a minimum cost. Let us explain our meaning. It has been said that there are always two sides to a question. It may be further said that there are always three sides to a question, the two extremes and the middle ground. In any industrial research there are the highly theoretical side, the purely practical side, and the theoretico-practical side. To study a slag and be practical in the studying, there is something needed that represents in the laboratory (or in microcosm) what actually happens macrocosmically in the blast furnace. There is such a thing as the art of metallurgical research occupying the middle ground between theory and practice.

Jan 4, 1917

By C. M. Means

CONSIDERING the hazard involved in mining operations, statistics show, that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 250 to 500 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater. This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems.

Jan 4, 1914

By J. D. Pelletier

SAN MANUEL orebody is a disseminated copper deposit in quartz monzonite, monzonite porphyry, and diabase. Quartz monzonite, which is Pre-Cambrian1 in age, is exposed in an area including No. 1 and No. 4 shafts and extending about 2400 ft southeast from No. 1 shaft. It is also exposed in the bottom of No. 2 shaft and in a zone roughly 500 to 1200 ft southeast of No. 2 shaft having its long dimension along a northeast-southwest axis. Churn drilling has shown all these exposures to be parts of a contiguous mass of quartz monzonite lying within and beneath the ore zone.

Jan 7, 1957

Secretary Membership Committee Increase of Membership Papers and Publications Committee Library Committee Treasurer Report of the Secretary TO THE BOARDOF DIRECTORASN D THE MEMBEROS F THE AMERICANIN STITUTE OF MINING AND METALLURGICAENL GINEERS GENTLEME:N As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining industries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has restricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metallurgy have a greatly increased necessity for i,dormation and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowledge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrolment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1928

By Waldemar Lindgren

Introduction To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea.. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron Co.; to George W. Pfeiffer, General Manager, and to the several members of his staff.

Jan 10, 1915

By Paul R. Bluekamp

The Mather Mine property is composed of a 5.2 sq km (2 sq mile) area within the Cities of Ishpeming and Negaunee which are located in the Upper Peninsula of Michigan. Production in this mine started in 1943; it ran continuously until its closing in 1979, having produced slightly over 55 million tons of iron ore. This mine was a joint venture between several steel companies and The Cleveland- Cliffs Iron Company (CCI), with CCI being the fee holder and operator. For the first 17 years of operation, the ore was shipped in its natural state directly from the mine to the steel mill. By 1960, iron ore pellets were on the market and they proved so superior to the natural soft Mather ore that the latter became difficult to sell except for the coarser portions. It was decided to develop a pelletizing process for the Mather ore, and this was accomplished by 1965 when the first Mather pellets were produced. From this date, all but the coarse fraction of the Mather ore was shipped as pellets. The geological setting is that of a large east-west trending synclinorium which plunges to the west. The lowest member of this trough-like structure is, for the most part, a quartzite-like graywacke, the upper 20 m of which grades into a softer, fine grained slate. Lying conformably on this graywacke footwall member is an iron- formation member which is over 1,300 m in thickness. This iron-formation is cow posed of thin alternate bands of iron oxides and chert and is intruded by a number of diorite sills - some up to 122 rn (400 ft) in thickness. The north limb of this synclinorium dips at approximately 45' and bottoms out at about 1,000 m from surface in the central part of the mine. There are two sets of faults, many of which are intruded by diorite dikes, which trend east-west and southeast-northwest. Displacements are varied, reaching a maximum displacement of 243 m (800 ft). The ore is found lying directly on the slatey footwall and its position is largely controlled by the faults and dikes, with the bulk of the ore being on the upper side of these structures. The ore is composed of soft earthy hematite and martite with vertical thicknesses up to 122 m (400 ft) although the average thickness would be closer to 46 m (150 ft). The ore averaged 60% iron and 7% silica on a dried analysis. The Mather Mine is located on the north limb of the syncline and was worked from two shafts, the deepest of which. was 1,09 7 m. These two shafts are about 2 km apart and serviced a total of 8 working levels between them during the life of the mine. The level spacing was about 61 m (200 ft). The main haulageways were driven parallel to the ore/footwall contact in the hard cow petent graywacke wherever possible. On the lower levels, deeper into the footwall, naked development was common. This material graded into roof bolting ground towards the upper stratigraphic portion. As drifting progressed further into the upper stratigraphic portion of the footwall, progressively stronger steel sets had to be used. From the main haulageway, cross-cuts were turned into the orebody on 61 m (200 ft) centers and extended as far as needed to recover the ore available to that particular cross-cut. The main haulageways and cross-cuts were driven 3 m (10 ft) high, 3 m (10 ft) wide at the top and 4.6 m (15 ft) wide at the bottom. This configuration would accomodate a set composed of a 2.7 m (9 ft) cap on top of two 2.7 m (9 ft) legs angled out at 18'. A sill plate was used under each leg to prevent its sinking into the ore below. The type of steel used was dependent on the expected weight to be experienced. Sets were placed on 1.63 m (5 ft 4 in.) centers; however, in extremely heavy areas, it was sometimes necessary to install sets on 0.8 m (2 ft 8 in.) centers. On the top two levels (5th and 6th), the ore was considerably hard-er and was mined by sub-level stoping and long hole drilling. Very light steel sets were used in the main haulageways and cross-cuts and timber was used in the production drifts. Some con- crete production drifts were installed on 6th level, but proved to be uneconomical. However, as mining reached greater depths, the ore became softer and more massive, reaching its maximum vertical heights on 11th and 12th levels. On levels 7 through 10, yielding steel sets were used extensively in the slusher drifts. While they were satisfactory on 7th and 8th levels, their success diminished with depth and they were

Jan 1, 1981

THERE has been a lot of talk about the shortage of engineers and we have done our share of it; but recently we heard a spot radio commercial-between broadcasts-urging high school seniors to study engineering. We think this is going too far. Engineering is an exacting profession requiring the highest personal qualifications. Publicity for the purpose of interesting capable young people in choosing courses in engineering should emphasize qualification. The opportunities for a career in a great constructive profession which is the basis of our high standard of living should be properly evaluated. Although there is a need for more engineers today, nobody knows what the employment potential is going to be four years hence. The profession may do itself a grave disservice by attempting mass recruitment in the face of an unpredictable national economy. The mining and metals industries are in a special position as fewer engineers are needed in these fields. Only 10 pct of all engineers are mining and metallurgical engineers. Today's shortage is not so much in recent graduates, but in trained practicing engineers. The shortage has served the profession to good effect because it directed the talents of engineers into more productive channels. In some areas high school graduates have been put into routine jobs such as, surveying. If there is one thing the mining profession does not want, it is an oversupply of graduates which would relegate college men to years of work and discouragement in routine jobs. The public has a clear cut picture of the legal and medical professions and thus the respect knowledge imparts. But the engineer is variously thought of as a man who pulls the throttle lever on a locomotive, tends a furnace, or builds a bridge. The term engineer is too loosely used. For instance we have heard of "crowd engineers" and "exterminating engineers." In some unions an engineer designation has been established to describe a person doing routine checking or other control job. We do not disparage these positions but they are different from the work done by the man qualified by years of experience and study. Many of these so-called engineers are not engineers at all. The engineering profession has cooperated closely on a program of recruiting high school graduates for engineering study. It should start a cooperative public relations program to enlighten the public on the accomplishments and work of engineers. This type of publicity need not be of the bombastic type. It can be educational and dignified. Radio, television, and the periodicals can be used to convey information. It is time that laymen and interested young people learn to make a distinction between the true engineer and the technician. Such a program would instruct parents and high school students and thereby interest the right type of people in the engineering profession. The Centennial of Engineering sponsored by the American Society of Civil Engineers is a step in the direction of instructive public relations. This fine start should not be allowed to remain as a one pass venture. The engineering profession as a whole should follow this exposition with a sustained, well directed effort to inform the public of the engineer's work and the possibilities it holds for a constructive career.

Jan 1, 1952

By E. F. Loiseau

In a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it mas expected that a plan devised by Dr. Charles N. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust nixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one half of the lumps produced by the press. The plan mas abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is usually dry pitch, which is prepared by separating from the tar, at a temperature of 572' Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392' Fahrenheit. But with common tar very weak fuels are obtained, which do riot burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By James Douglas

Though liberality is not supposed to be a prominent trait of the Scottish character, Canada owes to a Scotchman, Sir Wm. Macdonald, more than to any other of its people, not only wise ideas, but pecuniary help towards extending education: and another Scotchman, in New York, has sumptuously housed under one roof three branches of the engineering fraternity, of which we are one. Having thus created us members of the same family—for the metaphorical meaning of house and kinship is identical—Mr. Carnegie expresses more emphatically than even he could in words, that, by aff'ording facilities for closest intercourse, he invites the mechanical, electrical and mining engineers to participate in the freest interchange of idea and experience, and to correlate and combine the results of their studies and activities; and, being members of the same household, to banish reserve and secrecy. And now we, the members of the American Institute of Mining Engineers, meet as though we were at home in a neighboring country. For whether we meet in Canada, in England, or elsewhere, the Institute is always received as though no political or geographical divisions separated its members from those of congenial associations in the land of its host. In truth, the title which we have assumed claims for the sphere of our activities the whole American continent, regardless of such trifling details as boundary-lines. The fact that we meet to communicate each other's experience, to discuss our difficulties, and to seek each other's aid in solving the intricate problems that so often present themselves in the course of our professional life, is an acknowledgment of our individual helplessness; and therefore an argument for united effort. But no effort can be of any value if there is an underlying suspicion

Jan 1, 1908

By James Barr

WHEN phosphate mining operations first commenced in Tennessee the loss of both high- and low-grade material was large, because of the crude hand methods employed. Practically all rock smaller than 2 in. was thrown back into the pits and covered with the overburden of subsequent openings. With the advent of mechanical washers and other mining machinery, together with the abolishing of the contract system, the waste has been steadily diminished, until at present only the finest sand is being rejected; and even this is not lost, for in the majority of cases the water, slime, and sand from the washers are run into large settling ponds where practically all of the phosphate-bearing material is caught and stored for future use, or until it is profitable to ship lower grades. The latest equipment used to recover the fine and lower-grade phosphate sand includes Dorr thickeners, settling tanks, Dorr classifiers and settling ponds served by locomotive cranes with clam-shell buckets, making it possible to save material averaging as fine as 200 mesh. To attempt saving finer material would necessitate a different type of drier, which might be patterned after the multiple-deck roasters. The present tailing runs from 15 to 25 per cent. of available phosphate, which, however, as mentioned before, does not represent a total loss to possible future operations. The demand of the consumer is the greatest factor in regulating the recovery at present. In the mining of blue rock, which does not require washing treatment, the main waste material is the capping of low-grade kidney forma-tion, generally used for backfilling of the rooms. By reason of the introduction of improved methods in the early stages and the re-mining of territory skimmed over at the start, at the present time the net result of all operations is a comparatively small loss.

Jan 2, 1916

By Henry G. Granger

DURING upwards of three thonsand miles of canoc-travel in South America, including several mishaps, the writer has unfortunately lost his book of notes taken during the year 1894 in Dutch Guyana, or Surinam. But a year spent in a foreign country, visiting its principal mining properties, is necessarily productive of indelible memories and impressions, and some of these may be of interest to the Institute. The Guyanas include British, or Demerara, Dutch, or Surinam, French, or Cayenne, and the Disputed Territory, or that portion of Brazil on the northeast coast of South America. After passing the picturesque mountainous coasts of Colombia and Venezuela, one reaches a low, flat mud-bank which extends far out into the sea, so that from the steamer, over a couple of leagues of turbid, shallow water, one call just see the dismal outline of the pestilential "bush" that fronts the Caribbean sea, clear around to the mouth of the Amazon. Here, iii the order mentioned above, are the Guyanas. So much has been said about this out-of-the-way section during the late excitement over the Venezuela boundary question, that the historical part of the subject may be advantageously condensed. Gold-mining in the Guyanas is altogether placer-mining, and is of the same general nature throughout; hence by describing the methods in use in Surinam and the results there achieved, ail idea will be given of the work throughout the field. The product of this section is about three to four millions of dollars annually, mostly from Demerara, not because of superior richness of its placers, but as a result of its very much larger population, which exceeds twice the aggregate census returns of both Surinam and Cayenne. Mining ill all this section is of comparatively recent date, and is indirectly due to the decline of the sugar-industry. After the introduction of beet-sugar scores

Jan 1, 1897

By Henry S. Drinker

THE Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler property, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the fourteen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbonaceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meeting, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone-walls in V-shape running from the apex of the V towards the outcrop, were built to cut the fire off, and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By Oswald J. Heinrich

IN the coal review for the United States for 1875, the Engineering and Mining Journal, January 1st, 1876, remarks about the Richmond coal basin " It has contributed but little to the supply of fuel during the year past, notwithstanding the fact that it is the most favorably situated of all our coal-fields, and possesses a fuel of good quality, well adapted to many important uses. An unaccountable lethargy seems to have fallen on all who have touched this field ; and yet, in the future it can scarcely fail to become one of the great sources of coal supply." In most respects indorsing the above remarks, I take occasion to lay before the Institute the following facts in defence of the Rich¬mond basin; and not willing to criticize other mining enterprises in this field, I will make this one remark in general for all of them. While it is true that very little coal has been raised during the year in this field, it is equally true that even the little that has been raised could hardly be sold. When the output of the largest coal districts in the United States decreases, in consequence of the state of the market, it is not to be wondered at that the former small output of this basin dwindled down to almost nothing. But a far deeper¬seated evil, under which this field is suffering, may be discerned from the following remarks, which I hope will show that the latter part of the above remark in the Journal is not altogether fair. As the history of one mine in this district very nearly represents the history of the whole field, I will endeavor to give an account of the development of the Midlothian Mines, ranging amongst the old¬est in the district, partially taken from a report of Col. Wooldridge, in 1841. Coal was mined in this neighborhood as early as 1700, and used (then so-called extensively) in the vicinity in 1775. A

Jan 1, 1876

By John A. Church

THE Lake Superior blast-furnaces probably represent the maximum economy of fuel possible in this country. They smelt an ore which is very rich and easily reducible, and as the small amount of gangue present is not all silica, but in part a silicate, the amount of limestone required is a minimum. The average yield of the ore treated at six furnaces was 63 per cent., and the average quantity of limestone 179 pounds per ton of pig. The fuel used is charcoal, so burned as to retain most of the combustible volatile part, which, before the utilization of furnace-gas, was burned away. With these conditions it is not surprising that the Lake Superior charcoal practice is extraordinary in almost every respect. In any scientific discussion of American furnace work, the establishments there will be found at the head of the list, and they work under conditions which are extremely favorable for careful study. The Bay Furnace, near Marquette, has the honor of carrying "the broom" for the largest daily make. With a capacity of 1908 cubic feet it has, for months together, produced 29 tons of pig, graded at

Jan 1, 1876

By H. H. West

Modern mining is vitally concerned with the prompt, efficient movement of great quantities of bulk materials. It is not surprising, therefore, that intensive efforts are being directed toward improving effectiveness and reducing costs of materials handling systems. Historically, the operation of removing bulk material from a moving conveyor and depositing it in utilization or storage areas has been a high cost segment of the materials handling system. Since this operation is often performed by belt trippers, considerable attention has been focused on improvement of these devices. Frequently, the greatest opportunity for improving performance of these devices is the incorporation of remote or automatic control systems. This article describes tripper control systems developed by Kennecott Copper Corp. and explains the control philosophies used in designing these systems.

Jan 3, 1963