Search Documents

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By Wolfgang Pietsch

Pressure agglomeration using tableting machines, roll presses, punch presses, isostatic pressing equipment, extrusion presses, and other less common equipment, represents a large share among commercial applications of size enlargement by agglomeration. The paper attempts to classify and describe the equipment and technology, their development and state of the art, as well as their respective applications, advantages, and disadvantages.

Jan 1, 1977

By James J. Scott, John J. Reed

In a year fraught with difficulties, especially to small operators, the more stable mining organizations have shown a dynamic readiness to plunge ahead in the development of new mines, new and ingenious equipment and new tools for management to take the guesswork out of important decisions. New Mining Equipment The mining equipment display at the American Mining Congress in San Francisco demonstrated some rather radical new design concepts and a new willingness to use imagination to come up with ingenious new applications and adaptations of standard equipment.

Jan 2, 1963

By J. H. Johns, G. R. Stephan

The Climax mine has a history of dealing with ground control problems caused by major stress concentrations in the orebody. These stress concentrations, called weight, can arise in a variety of ways. The general effects of depth, rock type, and mining method give rise to weight problems, but local geologic features and daily cave line management can have even greater effects. Over the years a number of techniques have been developed for identifying weight problems in advance and for cow with them. These techniques all help us to amid interrupting the pace of cave advance and minimize the loss of production.

Jan 1, 1984

By David Firewick, Daniel Stewart, Richard Rein

Panel caving of the Henderson orebody began in August, 1976. Fifty months later, on September 10, 1980, the cave zone appeared on surface as a steep-walled cavity positioned directly above the initial cave area. Although surface survey data revealed the development of a slight depression over the production area, surface inspection by geologists, three days prior to breach- ing, resulted in no evidence of impending glory-hole development. Geologic factors such as rock contacts and alteration-zone boundaries had little influence on the location of the initial glory hole. Since initial breakthrough, the glory-hole shape and growth have not directionally followed caveline advance because of topography and faulting. Based on periodic data, mine production has resulted in immediate growth of the Henderson glory hole.

Jan 1, 1984

By Joseph Pogue

THE writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, FIG. 1.-SKETCH MAP SHOWING APPROXIMATE LOCATIONS OF ALL IMPORTANT EMERALD MINES AND PROSPECTS IN COLOMBIA. (Data in part supplied by Robert Scheibe, July, 1915.) Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 5, 1916

By Forbes Wilson

IN February 1952 Freeport Sulphur Company started exploration work on a group of lateritic deposits at Moa Bay, Cuba. As a result of successful exploration work and a vast amount of metallurgical research over the past five years, these deposits will soon become a new Free World source of nickel and cobalt. Moa Bay lies on the north coast of Oriente Province, the easternmost part of the island, about 600 miles east of Havana and about 40 miles east of the U. S. Government nickel plant at Nicaro.

Jan 5, 1958

By R. Neilson Clark

THE discovery of a thin pay streak, yielding carbonates of copper, native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

Jan 1, 1967

By F. Hass, N. W. Lord

This paper gives the results of experiments conducted in the metallurgical laboratory of the Ohio State University with the objects of determining: First, the calorific powers of a number of coals in general use in Ohio; and second, how far ordinary analytical methods could be used as a basis for computing these values. Incidentally a test of the performance of the calorimeter was involved. The chemical work has been carried on in the department for some time, so that the whole investigation has extended over three or four years. The Mahler calorimeter was purchased from L. Golaz in Paris, and is practically identical with the one described and figured by Mahler in his monograph "Contribution a l'Etude des Combustibles," from the Bulletin de la Société d' Encouragement pour l'lndustrie Nationale. A figure and description is also given by William Kent in The Mineral Industry for 1892, page 97. There were furnished with the instrument three thermometers covering a range of from 7°.5 C. to 31° C. Thermometer "A" (17°.5 to 31°) was carefully calibrated by reading the ends of a thread of mercury in sixteen positions covering the whole scale, supplementing this by readings of longer threads and deducing the errors of scale by the method published by Prof. Holman in the Technology Quarterly of September, 1887. The maximum error of a single reading was found to be 0°.0042 C. Thermometer "B" (13° to 25°) was compared directly with " A " over the scale common to both, and a variation was found of 0°.0145 C. for 7°.5 (or 0°.002 for l°) of the scale. Thermometer " C" ('7°.5 to 19°.0) was omitted from the cornparison, as it was rarely used, being only required where measurements were made at low temperatures. From the

Jan 1, 1898

By Paul A. Farrar, Harold Margolin

The system Ti-Cr has been re investigated From 40 to 100 pct Cr. The high-temperature modification of TiCr, was found to exist in the temperature range from 1365 where it terminates in the eutectoid reaction TiCr,(TI)* — HE chromium-rich region of the Ti-Cr system was investigated by Vogel and Wenderott,' Mc Quillan,' Van Thyne et dl.,' and Cuff Duwez and Taylor determined the crystal structure of the low-temeperature modification of TiCr, to be fcc a = 6.943A and Levinger' discovered the existence of a second (high-temperature) modification of TiCr, and determited its crystal structure to be hexagonal a = 4.932A, c/a = 1.617i. No information was obtained as to the temperature range over which each modification of TiCr? existed; therefore the present investigation was initiated. I) Experimental Techniques Alloys employed for the delination of this system were prepared from iodide titanium and high-purity chromium. The purity of these materials is as follows: Iodide titanium: purity 99.99 pct; major impurities—carbon 0.0001 pct; oxygen 0 to 0.002 pct; nitrogen 0 to 0.002 pct; silicon 0 to 0.005 pct; manganese 0.001 pct; copper 0.001 pct (Foote Mineral Co., Lot 609-29). Chromium #1: metallic purity 99.997 min.; interstitial content—oxygen 0.27 to 0.46 pct; hydrogen 0.028 to 0.038 pct; nitrogen 0.0002 pct (Ave-quipo Inc.). Chromium #2: purity 99.9 pct; major impurities—carbon 0.01 pct; oxygen 0.013 pct; nitrogen 0.02 pct; silicon 0.01 pct; sulfur 0.03 pct; iron 0.01 pct (Fulmer Research Institute Ltd.). A total of sixteen alloys of thirteen different compositions was prepared in the range from 40 to 95' *All percentages are given in weight percent. pct Cr. The compositions of the alloys prepared were as follows: Ti-40, 45, 50, 60, 62, 64, 66, 68, 70, 80, 85, 90, and 95 pct Cr. Two buttons were prepared of the 66, 90, and 95 pct Cr alloys. The 40 pct Cr and one of the 66 pct Cr alloys were prepared from the chromium # 2. All the other alloys were prepared from chromium #1. The alloys were arc-melted as 25-g buttons in a copper-hearth glass-walled furnace7 under an inert atmosphere of high-purity helium. The alloys were sintered at 250 amp and melted twice at 350 amp for 30 sec with the buttons being turned over between melts. Weight losses during melting were determined and in the range 45 to 68 pct Cr they were found, in all cases, to be less than 1.25 pct of the total alloy weight. A number of the high-chromium alloys shattered during cooling from either the first or second melt, which made the weight loss considerably larger than usual. The 70 and 80 pct alloys lost approximately 5.7 pct of their total weight, the 85 pct alloys 1.5 pct, the 90 pct alloy 2 pct, and the 95 pct alloy 3 pct. However, it is felt that the actual composition of the alloys in this region is probably within approximately 1 pct of the intended composition, as a large portion of the material lost was that due to shattering after melting. Nominal compositions were therefore used in plotting data and referring to the alloys. The alloys were cut into specimens, wrapped in molybdenum sheet, and encapsuled in argon-filled quartz or Vycor tubes for heat treatment. The heat-treatment times and temperatures are given in Table I. The specimens were quenched in iced brine (I.B.Q.) following heat treatment. The standard techniques of grinding, polishing., and etching were used in preparing the specimens for metallo-graphic examination. For alloys below 68 pct Cr

Jan 1, 1963

By Walter E. Heinrichs

Since World War II exploration geophysics has derived its scope from the following factors: first, the usual post-war interest in exploration to rebuild war-depleted reserves; second, the impetus supplied by the uranium prospecting boom; third, increased demand for natural resources due to the Korean War; fourth, the discovery of substantial metallic ore by geophysical means in Canada, the U. S., and other countries; and, finally, continuing discoveries of commercial oil by geophysical methods throughout the world. The past year's national business slump has severely curtailed mining exploration in general and correspondingly has brought about even greater reductions in applied geophysics in mining. Petroleum exploration, conceived and executed on a broader statistical basis than mining, has kept up its geophysical programs relatively well, although domestic work has been substantially reduced.

Jan 7, 1959

By John Harmon

THIS paper was written-with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system.

Jan 1, 1931

By Wm. Wallace Mein

IN March 1949 the Calaveras Cement Co. was sued by five landowners whose properties are located in the vicinity of the plant. These landowners-all of them cattle ranchers-sued for dust damages of $120,338 and for an injunction preventing the company from casting dust upon their properties in injurious quantities. The issue was split, the jury deciding the amount of damages and the court handling the injunction features. The action came to trial before a jury in April of that year and resulted in damages being awarded in the amount of $7,508. A month later the court issued its injunction requiring recovery of stack dust to an 87 pct minimum.

Jan 6, 1951

By T. L. Kesler

With only six small spodumene prospect pits, no detailed mapping, and no subsurface information in 1938, the Carolina lithium-pegmatite area now contains four mines among more than 25 properties on which exploratory work has been done. Even the open pit mine of Foote Mineral Co. described herein, from which ten million tons of ore and waste have been removed since 1952, was virgin ground when mapped in 1938-40 1. It has been a privilege to participate in the transition. In 1940, the spodumene pegmatites were known in a 25-mile belt (originally noted for tin prospecting) between Lincolnton, N. C. and Grover at the South Carolina line. Subsequently, Broadhurst 2 reported relatively small bodies northeast of Lincolnton near the Catawba County line. To the south, diamond drilling done in 1953 on the old Ross tin-mine property near Gaffney yielded pegmatite cores containing a few crystals of spodumene. This fact, not previously reported, suggests that some of the pyroxene in the Ross shaft as described by Sloan 3 may be spodumene.

Jan 9, 1961

After a year-long study comparing existing crafts and techniques for ocean exploration with the future needs of oceanologists, the University of Pennsylvania's ocean engineering research team has come up with a system proposal for prolonged deep-sea exploration. Given the assumption that it will be necessary to re-explore our oceans every 25 years or so, engineers from the University's Towne School of Civil and Mechanical Engineering believe the best sys- tem for future ocean exploration would consist of a stable, manned surface ship operating and controlling two types of vehicles-an unmanned untethered craft for broad search missions, and an unmanned, tethered vehicle for detailed work.

Jan 12, 1969

By G. F. Dillion, A. F. Armington

THE present method for the ultrapurification of boron involves the formation, distillation, and decomposition of boron tribromide.' However, the boron tribromide prepared contains several impurities in the ppm range, even after distillation. Some of these impurities, notably carbon, can be reduced after decomposition by zone refining. In this study, a comparison of the purity of boron tribromide at various formation temperatures is presented. The apparatus employed consisted of a bromine flask connected to a 22 mm ID horizontal quartz reaction tube packed with amorphous boron powder, which was in turn connected to a receiving flask cooled with an ice bath. Argon was used as a carrier gas. The approximate rate of passage of bromine to the reaction tube was 25 g per hr. The reaction was first investigated at several temperatures in order to determine the lowest temperature necessary to produce a colorless product which was assumed to be an indication of complete reaction of the bromine. The lowest temperature found in this study was 420oC. The amount of impurities found in the boron tribromide at various formation temperatures is shown in Table I. The data presented are emission spectroscopic results of boric oxide produced by the hydrolysis of 2 to 3 g of boron tribromide in 10 ml of distilled water. After hydrolysis, the samples were dried several hours on a hot plate. Assuming equilibrium conditions in the reactor, one can make approximate thermodynamic calculations estimatling the completeness of reaction of bromine with boron and its impurities at various temperatures. Data for these calculations were taken from Rossini,3 and must be taken as approximations since the T?S factor was not included in the calculations. The results of such calculations indicate that, with the exception of carbon bromina-tion, all impurities would react almost to completeness (> 99 pet) at all temperatures between 400" and 900oC. In the case of carbon, which cannot be accurately analyzed spectroscopically, it is estimated that only about one sixth as much carbon tetrabromide would be formed at 400" than at 900°C. Since some marked reductions in impurity content were observed at the lower reaction temperature which would not be predicted by thermo-

Jan 1, 1962

By James E. Dunn

For several years, ground support at the Pitch uranium mine has been a serious headache to the management. The "moving" ground raised havoc with standard timber sets as well as steel sets. The author discusses this problem which has led to the adoption of heavy cribbing practices in drifts and raises.

Jan 6, 1961

By C. Feng, W. E. Krul

A study was made of the development of texture and the anisotropy in plastic flow of Ti-8Al-1Mo-1V alloy. Based on Pole figure determinations, the shifting of texture induced by rolling at approximately 400°C was found to be due primarily to slip rotation for the major Portion of the material. Grain boundary shear is believed to be an important factor. The anisotropy of the textured alloy was examined in terms of the variations of yield stress under tension and the ratio of bi -axial strain increments µp, in the temperature range 25" to 290°C. The results were related to Hill&apos;s theory on plastic anisotropy. The Schmid factors of (1100)[1120], (1101)[1120/, and (1101)[1120] slip systems were analyzed and found to be compatible with the observed anisotropy. Cross-slip between these planes was proposed as a possible deformation mode. In a number of published articles, considerable interest has been directed to the possible achievement of texture hardening in hcp metals. Following Backofen, Hosford, and Burke,&apos; this phenomenon was related to the yield criteria of the material and was expressed in terms of the biaxial strain ratio, r = d?w/d?l. The higher the value of r, the greater is the expected potential for texture hardening under certain loading conditions. For a given material, r varies with direction. Such variation can be traced to the anisotropy in plastic flow and can be explained within the framework of the various modes of deformation. Hatch2 found that a high r value coincides with a texture whereby the (0001) pole is closely aligned with the surface normal for sheet materials, Based on the analysis of the slip on the {1010}, {1011}, and (0001) planes, Lee and Backofen3 and Avery, Hosford, and Backofen4 concluded that the resistance to thinning is reduced by the operation of the (0001) <1120> slip system; with this reasoning they were able to explain the low r values (i.e., r « 1) observed in magnesium alloy sheets in the rolling direction and in commercially pure titanium in the transverse direction. The general equation, dealing with plastic flow in a polycrystalline aggregate has been used to correlate the plastic anisotropy and texture. In this expression, T and s are shear and normal stresses, and dri and d? are shear and normal strain increments, respectively. Assuming that five slip systems are operative within each grain and applying the principle of maximum work,5,6 one can determine the m value among the available systems. On this basis, Hosford7 and Chin, Nesbitt, and Williams&apos; were able to correlate m with yield stress under plane-strain compression, and Svensson9 was able to predict the variation of yield stress in textured aluminum. These workers made their analyses from materials in which slip operation is known to be associated with plastic flow. Questions remain regarding the derivation of Hill&apos;s theory on plastic anisotropy,10,11 since it was formulated on von Mises&apos; yield criterion.&apos;&apos; Its ability to deal with other forms of deformation has been in doubt.13 Others have discussed the validity of Hill&apos;s quadratic equation relating strain and yield stress.14&apos;15 For hcp titanium, deformation by various modes of slip and twinning operations has been reported.16-20 If all possible modes of deformation operate and contribute substantially to the plastic flow, it is difficult to imagine how the quadratic expression can suitably describe the anisotropic plastic flow of titanium alloys. Backofen and Hosford15 considered that Hill&apos;s is a macroscopic theory and implied that the major mode of deformation by slip mechanism will adequately describe anisotropy of the material. In the present investigation, slip operation will be shown to play the major role in the development of sheet texture induced by rolling of a commercial titanium alloy. Although twinning and other modes of deformation may also operate, their operation is believed to be secondary. The anisotropic properties of the sheet, which can be expressed in terms of directional variation of r, µp = -d?w/d?l and the yield stress will be shown to be governed primarily by slip operation. MATERIALS AND EXPERIMENTAL TECHNIQUES The titanium alloy chosen for the present investigation had a nominal composition of 8 wt pct Al, 1 wt pct Mo, 1 wt pct V, and 0.1 wt pct interstitial impurities. Sheets varying between 0.1 and 0.15 in. thickness were used. The alloy was received in a condition which was prepared by rolling at 900°C and annealing at 700°C. Subsequently, the sheets were subjected to further reduction in thickness by rolling at 400°C. A total reduction in thickness of 65 to 70 pct was obtained by a series of quick passes in a rolling mill with intermediate reheating. Further reduction in thickness was not possible due to cracking developed at the edges of the sheets. X-ray measurements were conducted in a Siemens and a Norelco unit to determine the texture of the sheets. Reflection techniques were used exclusively with CuK, radiation and a nickel filter. The loss of X-ray intensity due to geometric defocusing was calibrated with a technique described previously." The (0001), (1010), and (1071) pole figures were plotted from 0 to 80 deg, and to present the texture elements quantitatively, inverse pole figures were constructed following the technique described by Jetter, McHargue, and Williams.22 Tensile experiments were carried out at 25", 175",

Jan 1, 1970