Search Documents

By George Rice

SINCE my earliest recollection, the coal business has been in a state of unrest. It has always been a matter of bewilderment to the serious thinking, the instability of this most important industry; second only to agriculture in its effect on the great development of this country, and even more important in certain aspects, because without fuel railroads could not run, agriculture could not get its products to market, nor would the great manufacturing enterprises have been possible. I will not attempt to discuss the present serious -labor dispute or similar disagreements of the past; in the settlement of which more or less successful attempts have been made to equalize, temporarily at least, natural conditions through "joint agreement" as to prices paid labor; but will confine my views to the general underlying conditions of which the disputes are symptoms, and try to show how these must be remedied before there can be any hope of stabilizing conditions.

Jan 5, 1922

By George B. Clark

More economical methods of rock disintegration are needed for mining and for rapid excavation. Two major systems are drill and blast and mechanical excavation, including tunnel-boring machines. Current drill and blast methods are cyclic and there- fore limited in speed of operation. Boring machines are limited to moderately hard rock due to bearing and cutter wear. The recent development of ANFO, which has reduced blasting costs markedly, was largely fortuitous because of the method of manufacturing AN prills. New slurries and fluid explosives are easy to load and have high energy-pressure characteristics.

Jan 1, 1971

By R. A. Matuszak

Abstract-Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far, and improves the performance characteristics.

Jan 2, 1978

By Eugene B. Wilson

The development of coal-mines has kept pace with the facilities at command for ventilating and lighting. In fact, it was formerly • customary to leave unworked those mines, or portions of mines, in which naked lights could not be used without danger. Attention was then turned to the ventilation; but even with improved ventilation, the naked light was often unsafe. The new era in coal-mining dates, we may say, as far back as 1815, when Sir H. Davy and Mr. George Stephenson discovered the principle of the safety-lamp. Since then many improvements have been added to their lamps, but

Jan 1, 1885

By W. F. Mullen

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behre1 and Bowles 2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate.

Jan 12, 1951

By Eugene Guccione

FOREWORD-In an interview published in the May 1975 issue of MINING ENGINEERING, one of the world's most respected scientists, nuclear physicist Hans Bethe discussed the reliability of nuclear power plants and their unmatched safety record. The Nobel laureate also refuted the anti-nuclear lobby's claims that nuclear plants emit harmful radioactive effluents. When asked whether the US has sufficient uranium resources, Dr. Bethe replied that "it depends on the time of introduction of the commercial and advanced breeder reactors which, in effect, can generate more nuclear fuel than they consume." The United States has enough U3O8 to last until the breeders can take over in 1995, said Dr. Bethe. But lie warned that extensive environmental damage would be caused if "environmentalists" succeed in delaying the development of the breeder. Any such delays, he noted, would vastly increase the demand for U3O8 in conventional reactors; this, in turn, would impose an immense burden on the US uranium mining industry, which would then have no alternative but to mine the low-grade Chattanooga deposits.

Jan 4, 1977

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at '75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By Eugene P. Pfleider, Claus Freyberger

Generally, the different methods of financing new mining projects are not well understood by the engineers and supervisory personnel. Nor are the effects of these alternatives on depletion, taxes and profitability readily apparent to even the sophisticated management personnel without the aid of cash flow studies. Fortunately, with the advent of the computer it is possible now to simulate many different combinations of 1) equity, 2) loan and 3) production payment financing with little effort. A general computer program for cash flow analysis of mining ventures has been developed and applied as a case example to a 1967 feasibility study of the Underground Mining of Minnesota Taconite. The effects on profitability as measured both in rates-of-return and present value are presented for various financing combinations. In addition, percentage depletion rates were altered so as to measure the impact of this statuatory allowance. Based on the cost data as presented in the aforementioned 1967 feasibility study, and assuming 7% loans, the rates-of-return vary from 9. 9% to [00] % on equity variations and from 9. 9% to 11.4% on total invested funds.

Jan 1, 1969

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria 'Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By H. M. Chance

Within the last 10 years the subject of mine taxation in its relation to coal-mining interests has come to have growing importance, not only to those engaged in the mining of coal, but also to the owners of land underlain by coal.

Jan 1, 1915

By G. M. Wells

A view of the map of Floridat shows the phosphate-deposits to lie on the western side of the State, extending southward over

Jan 1, 1896

By Bruce A. Kennedy

The 1960's were an apparent turning point in the technological and social attitudes and awareness of the mining industry. From the late 19th century through to the early 20th century, one has always been presented with the picture of the rough and ready leaders of the mining industry who screamed for production and damned anything that got in the way of it. This attitude led to a certain alienation of the mining industry in the eyes of the general public. They saw an industry which was archaic in many of its practices and often heartless in its attitudes towards mankind. However, a gradual change spread through the industry and cracks began to appear in the hard facades of the mining companies. Resistance to change had almost become a standard operating procedure for many and consequently changes in technology had been slow in coming. The late 1950's and the 1960's saw a new awareness come into existence. As the mining company managements changed, there developed a realization that considerable efforts had to be made to bring the technology and social standing of the industry out of the dark ages and into the modern world. New advances were made in both metallurgical and mining technology. The 20th century technology of computers was accepted and became a standard tool of the industry.

Jan 1, 1971

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

By E. Gilpin

The Nova Scotian gold fields have yielded so little in comparison with those of the United States, that a lengthy description of them would almost appear unnecessary. However, not only are they interesting from a geological point of view, but experience has shown

Jan 1, 1886

By N. Nakanishi, C. M. Wayman

The effect of small copper additions on the mar-tensitic transformation behavior in Au-47.5 at. pct Cd was studied by measuring electrical resistivity as a function of temperature. The transformation behavior was found to change and transformation start (M,) temperatures for both the ß to ß' and ß to ß' transformations were depressed substantially by the addition of small amounts of copper. Both M, temperatures were lowered approximately 70°C per at. pct Cu. Copper also had the effect of narrowing the transformation hysteresis region (resistivity us temperature), and for the alloy Au-47.5 Cd-1.5 Cu there was little or no hysteresis; in this alloy, the reverse transfmmation upon heating apparently occurs below the thermodynamic equilibrium temperature, To. THE ß phase in the Au-Cd system occurs at the electron/atom ratio 3/2, and is similar to other ß phases in alloys based on copper, silver, or gold. It is of the CsCl type, in which a considerable degree of long-range order persists to the melting temperature.' The phase boundaries of the ß phase are not known precisely below 300° C, but at room tem- perature the phase exists from approximately 46 to 52* at. pct Cd.2 At low temperatures, the ß phase transforms in a diffusionless (martensitic) manner. Alloys having a composition near 47.5 pct Cd transform upon slow cooling to an orthorhombic3 phase, ß', at - 60°C. Alloys having a composition near 49.0 pct Cd, transform at - 30°C into a phase, ß", which has been recently identified as trigonal.4 Alloys having compositions near 48.5 pct Cd will transform into both the 0' and 0" phases over a range of temperatures. The progress of transformations can be observed

Jan 1, 1963

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution1 has been used, together with the exponential formula for size distribution, to evaluate the exposure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications.

Jan 12, 1957

By J. Blodget Britton

To the question, "Do the Pennsylvania anthracites contain phosphorus ?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Iron-masters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows

Jan 1, 1873

By Sterling G. Valentine

The annual .use of large quantities of sulphurous iron-ores (over 1,500,000 tons in the United States) has led to a search for the best methods of desulphurization, in order to make this material more available for the manufacture of a good quality of pig-iron. Although such ores can be used raw in small amounts, they must be previously roasted if they are to constitute the entire ore-charge of a furnace.

Jan 1, 1890

By Albert Burch

AN analysis of this subject demands a study of the theory and practice of the present system, conclusions as to its merits, and recommendations for remedying its defects if any be found. Theory of the Present Law The theory of the present law with reference to lode locations contemplates the existence upon the surface of mineral-bearing veins which have clearly marked boundaries, and which can be so readily traced that a locator may immediately mark the boundaries of his 600 by 1,500 ft. claim in such a way that the vein will pass through both of its end-lines. It also supposes that, having discovered such a mineral-bearing vein, the locator will at once post a notice upon such discovery, mark the boundaries of his location in such a manner that they can be readily traced, and from that time forward have absolute title to the ground embraced within such boundaries, as against every person except the United States. For initiating title to placer ground, the law presupposes the discovery of a valuable mineral deposit; but not necessarily in place, as in the case of lode claims; and the location must be made to conform "as nearly as may be" to the legal subdivisions of the United States public land survey. When the placer law was extended to include the acquisition of title to oil lands, no exception was made as to the necessity for the discovery of valuable mineral in advance of location!

Jan 6, 1914