Search Documents

By D. Jenkins

THE Franklin Laboratory was designed mainly for the analysis of the products from the two concentrating mills situated at Franklin and Sterling Hill, the most important determinations being the zinc, iron, manganese, lime, moisture and silica contents of the ores. Within the last 4 years, however, it has been found advisable to examine most of our supplies, and therefore additional space and equipment was allotted for the examination of such substances as oils, greases, soaps, alloys, fuels, paints, explosives and water. The building as shown in elevation (Fig. 1) and plan (Fig. 2) consists of a main or routine laboratory, an experimental laboratory, a water FIG. 1.-WEST ELEVATION. analysis room and the other accessories such as stock room, library, sampling and drying rooms and office. The main laboratory is further divided into a balance room and zinc analysis room. As the greater part of our determinations are volumetric, good light is a very important factor and with this in view the interior walls of the building were constructed of white enameled brick laid in Keene cement. These also have the additional advantage that they give a clean and attractive appearance to the room. The windows are large, being 76 by 44 in. and even on very dark days the light is good throughout the whole laboratory. Our zinc titration requires a constant light and as, on many days, especially in winter, the light is variable, we installed two Artificial

Jan 8, 1917

By H. M. Chance

The Choctaw coal-field is a direct westward extension of the Arkansas coal-field, but its coals are not like Arkansas coals, except in the country immediately adjoining the Arkansas line. From the base of the coal-bearing rocks up to the top of the coalmeasures, I find a total thickness of at least 8500 feet. This great mass of coal-bearing rocks consists of an alternation of slates, shales, sandstones and coal-beds, with their accompanying under-beds of fire-clay. Only one small bed of limestone was observed. This occurs near the middle of the series; it is about eighteen inches thick, and quite arenaceous. The formation is naturally subdivided by seven or eight thick beds of sandstone, varying from 50 to 200 feet in thickness, the outcropping edges of which form a series of more or less bold " hogback " ridges, the interbedded shales and slate forming the intervening valleys. The base of the coal-series is a massive sandstone, ranging from 100 to 200 feet or more in thickness, lying immediately beneath the Grady coal-bed, which is the lowest known coal. In the district embraced between. the Missouri, Kansas and Texas railroad and the Arkansas State line, this sand-rock usually forms a bold semi-mountainous ridge. This is the ridge through which the St. Louis and San Francisco railroad passes at Bryan station, where the Grady coal-bed is opened and worked, from which point it can be traced westward without difficulty, passing about three miles north of Le Flor on the same railroad, thence west to the " Little Narrows " (which is merely a gap in the ridge), 'and beyond to a point two miles west of the Thompson-McKinney place, where it swings abruptly north for a mile or more, only to resume immediately its westward course, forming for some miles the northern boundary of the valley known as the " Boiling-Springs Prairie," beyond which it trends somewhat

Jan 1, 1890

By R. Neilson M. E. Clark

(with map on plate I.) THE coal-beds of Canyon City are situated six miles below the town, upon the Arkansas River. At this point the Rocky Mountains have thrown out from their main ridge two spurs. The one to the north, containing Pike's Peak and Cheyenne Mountain, is known as part of the "Rim Range;" the one to the west and south is known as the `1 Green¬horn Range." Against these syenitic mountains, the later rocks are piled and uplifted; at right angles to the direction of this main uplift is the axis of a lesser plication. On the north, west, and south, the pitch is steep, gradually flattening as it approaches the centre of the basin and rising again to the east at a pitch of about 5°, thus forming a perfect basin, the centre of which is only three miles east of the base of the Greenhorn Range.

Jan 1, 1873

By Arthur F. Wendt

In the manufacture of charcoal-blooms, washing or cleansing of the ore from adhering gangue has been practiced for many years. A sluice-box is even to-day used for that purpose in the Southern Appalachian Mountains. For the Lake Champlain bloomaries hard magnetic ores are crushed with stamps and then sluiced or jigged in hand-jigs. The stamps used in the Lake Champlain region are of the most primitive kind. They consist of a trip-hammer, dropping on a perforated cast-iron plate, through which the crushed ore escapes. Only friable rock can thus be successfully treated. To render the raw ore friable, a calcining or burning in piles on a bed of cordwood is resorted to. An expense of 35 cents per ton of crude rock treated is thus incurred. The crushed ore is shovelled or otherwise fed into jigs without previous sizing, except such as is incidental to crushing through the perforated bottom of the stamping-machine. In jigging this ore, it is allowed to pass through the bedding into the "hutch." The tailings are scraped off and wasted. They contain a large percentage of fine ore. In many instances, this is regained by subsequent sluicing. Such was the condition of the industry, when the writer's attention was first called to it in 1882. No attempt had been made to introduce into thiS branch of ore-dressing the notable improvements adopted in concentrating the ores of other metals. The result of the writer's investigations was the building in 1882 of the "Crown Point Separator." At the Crown Point Mines, N. Y., lean ore unfit for the blastfurnace (containing less than 331/3 per cent. of iron), was concentrated and used in the bloomary connected with the mines. The ore was burned here as elsewhere, and treated as described. The plant designed by the writer for Crown Point, is nearly a counterpart of that since erected by Messrs. Copeland and Bacon, contractors, for the Theal mine, Putnam County, New York, which is illustrated by the accompanying plate. The only difference is in

Jan 1, 1885

By J. E. Sandor, P. F. Schmidt

A general review of the present knowledge of the semiconductor/oxide interface is given, with emphasis on silicon and germanium. The electrical properties of clean surfaces and the changes that occur upon oxidation are described. A brief disczcssion of the methods and mechanisms of oxidation of silicon is given, and the interaction between the semiconductor substrate and the oxide phase is considered. Physical properties of the oxide film, charge storage effects due to the dielectric, and some device applications of oxide films on semiconductors are discussed. THIS paper will be heavily preoccupied with the elemental semiconductors germanium and silicon. Undoubtedly some injustice is done thereby to other semiconductor-oxide systems, but it is not readily possible to cover all aspects of so vast a field in the present review. In considering the semiconductor/oxide interface, we may start out by discussing briefly an idealized clean semiconductor surface, and may then follow the changes brought about by oxidation, as the oxide is allowed to grow progressively thicker. The references given are not a complete list, but are to be taken as guides to the literature. Tamml suggested in 1933, based upon the study of a one-dimensional asymmetrical potential model, that localized surface states may appear at the surface of a crystalline lattice; it was pointed out by Fowler that these states should occur in pairs. shockley3 examined the origin of such surface states on the basis of a more general one-dimensional model and found that surface states may appear in the forbidden region between the highest filled and the lowest vacant band. This happens when the two bands overlap, as, for instance, the "s" and ('p" bands of the diamond structure. In a three-dimensional model these levels would produce a surface band which is half-filled for diamond, and the number of surface states should be approximately equal to the number of surface atoms. This picture of the surface has been refined by more recent theoretical work, like Handler's4 and Koutecky and Tomasek's~ without introducing essential modifications. When these concepts were applied to semiconduc-

Jan 1, 1965

By J. A. Porter

In offering some data relative to this property, and the treatment of its ores, it is proper to say that a purely scientific article has not been attempted. It is hoped, however, that the economic conditions presented may be of interest to the members of the Institute, and that a discussion upon the concentration of the ore may throw some light upon a very unsatisfactory part of the work. The Smuggler-Union mines are located at the head of the San Miguel river, just south of the water-shed between Ouray and Telluride. The latter town, reached by the Denver and Rio Grande railway, is most picturesquely situated, at ail altitude of 8500 feet, in a narrow valley, the lower portion of which exposes only the sedimentary rocks. Along the sides of the valley, large masses of coarse alluvial deposits are left high above the present channel of the stream. Although much placer-work has been done, and some very rich material has been found, the limited extent of the isolated tracts has made placer-mining in this locality generally unprofitable. The valley terminates two miles above Telluride in an amphitheater around which walls rise abruptly several thousand feet. Here the company's mill is situated, being reached by a Bleichert tramway from the mines and also by a spur of the Rio Grande railway from Telluride. At this point, not only are the reddish sandstone and conglomerate beds exposed, but the contact between the conglomerate and the overlying gray volcanic breccia is plainly in view, even at a distance of many miles. A marked stratification is noticeable, indicating the successive layers of igneous breccia, locally termed trachyte. Throughout the entire region this is the favorite name among the miners for the rocks composing the igneous cap of the San Juan

Jan 1, 1897

ALL the ores of any kind whatsoever, even though they be semiminerals and may be perfect in their qualities, have to be recognized by experienced and good sorters. These men must have a detailed as well as a general experience of the metals so that in this first preparation, which is most important, they may know how to distinguish the good from the bad, and to know what is rock and what is ore. They must use patience in this, breaking and cutting and king the ore from the earth. They must separate the good ore from the bad, avoiding as far as possible every occasion for poisoning it by traces of other ores, evil stones, or other things inimical to its nature. Finally, with the judgment of the eye and with tools, and, in the end, by roasting it with fire and then quenching it with water, or by washing and re-washing it, the ore must be made as pure as possible in order to join it better with the companions that seem to be the most beneficial for its needs. Ores would be useless stones without smelting. Therefore, when it is certain that such ores are of divers elemental mixtures, aid must be given to each one according to the evil ingredients [47v] that harm it. But because such evil qualities are things that are often not apparent to the eye, such as too great a burning, or too much earthiness so that when they are alone the fire burns these ores before it melts them, it is necessary to temper them with other materials. To do this it is necessary to have the ability

Jan 1, 1942

By Auguste J. Rossi

We cannot expect, within the limits of this paper, to treat this subject exhaustively, but will endeavor, in the following, to present it in as concise a manner as is consistent with a clear exposition of its importance. Ores of titanium, titaniferous iron-ores (that is, iron-ores containing a notable amount of titanic acid, TiO2,, say not less than 5 per cent., generally 10 to 20 per cent., and frequently more, up to 40 per cent. or thereabout), occur all over the world in immense quantity, " in mountain masses," constituting in some localities, as in Sweden, Norway, Canada, the Adirondacks (N. Y.), in North Carolina and other States of the Union, the geological formation itself, the igneous rocks having, in many places, been so permeated with the metallic oxides as to justify their being called iron-ores. As a rule they are Bessemer ores, quite free from phosphorus and sulphur, though not invariably so. When the percentage of titanic acid is very high, that of the iron is low, but the proportions do not necessarily vary in the same ratio; that is, a rich ore may contain more titanic acid than one lower in iron. The percentage of iron varies, being as low as 35 to 36 per cent. in real ilmenite. It is more generally not less than 50 to 55 per cent., reaching often an average of 58 to 60 per cent., and as high as 63 to 65 per cent. It is obvious that if these ores were to be considered in the same light as other iron-ores, equally rich in iron, they would form an excellent stock for blast-furnaces for years to come, as their supply might be called inexhaustible, and they could

Jan 1, 1903

By Albert H. Chester

DURING the summer of 1875 I visited some of the iron mines of Houghton County, Mich., and was quite interested to observe the progress made there within a. few years. Working in open pits is gradually giving place to underground work in most of the mines where this system is practicable. In some cases, as in the Lake Superior Mine, the body of ore is so irregular, and the deposit so liable at any time to be pinched out, or nearly so, that it has been found impractical, if not impossible, to lay out any plan for systematic underground work. But in many other mines the deposit is so regular in character, that the work can be laid out in shafts at regu¬lar intervals, and a series of 60 feet levels. The Michigammi Mine, opened in 1872, and first worked in 1873, is arranged on this plan, though some quarrying is still done. But the men are being put at overhead stoping as fast as it can be got ready for them, and before long it will all be worked in this way. The New York Mine is undergoing a similar change to the pillar system, and several others have either been changed, or it is about to be done. My principal object in visiting this region was to obtain samples from some of the important mines, so as to be able to answer the question : "What is the average percentage of iron in the Lake Superior ores?" Most iron furnaces work on mixtures of ore, so that it is impossible to tell, from their records, just the percentage in each one.

Jan 1, 1876

By Benjamin Gildersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 8, 1950

By G. L. Jr. Spencer

THERE is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least, only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiffness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges.

Jan 1, 1931

By G. L. Oldright, Virgil Miller

It is well known, in metallurgical circles, though less recognized in the technical press, that there have been remarkable increases in the capacity of the blast furnace in the last five .years. In places this capacity has been almost doubled. This paper will brief the experimental work carried on during more than five years with the direct assistance of the technical staffs of three lead smelters treating three distinctive types of feed. The first is the custom smelter of the International Smelting and Refining Co. at Tooele, Utah1, with a multiplicity of ores; the second, the Kellogg, Idaho, smelter of the Bunker Hill and Sullivan Mining and Concentrating CO.2, treating an exceedingly rich lead charge, such as is now being made more and more as the practice of concentration is improved; and the third, the smelter at Trail, B. C., owned by the Consolidated Mining and Smelting Company of Canada, Limited3, which treats highly zinciferous charges and later recovers zinc from the slag. In comparing operations at these three smelters it must be clearly recognized that the objectives in smelting differ through differences in economics. Many operations are not, then, strictly comparable. There have also been decided improvements in operation since all of the smelters were examined, though this was but a relatively short time ago. The general factors that govern speed in smelting and the loss of metals in the smelters examined will be stressed. (For details of operation the reader is referred to the original papers.) This paper will then be an examination of the fundamentals of operating units in a search for improvements, and not a description of three great lead smelters. Capacity of Blast Furnace Assuming a well prepared and self-fluxing charge to start with, enough coke must be added: (1) to melt the charge, particularly the slag-forming

Jan 1, 1937

By David S. Bolin

INTRODUCTION This paper is directed toward those companies or individuals who may be considering the possibility of tin exploration or development projects in South America. Although tin deposits are known in many countries of Latin-America including Argentina, Peru, and Mexico, the majority of the deposits are located in Bolivia and Brazil. These two countries also account for virtually all the current production. Many factors affect the economic decisions related to mining and exploration projects in this region including the following: 1) Types of deposits 2) Anticipated size and grade of deposits 3) Deposit geometry and ore distribution as it affects the selection of a mining method 4) Metallurgical amenability 5) Governmental policies 6) Taxation 7) Anticipated capital and operating costs 8) Marketing costs This discussion will be directed toward each of these points. The majority of the presentation will be concentrated on Bolivia as this country is the principal producer in the region, however, the potential for further tin development in Brazil is excellent. Due to the remote and previously almost inaccessible location of the stanniferous districts of Brazil, little is known with respect to size and type of non-alluvial deposits which may exist in this vast country. TYPES OF DEPOSITS Two major types of deposits are currently being exploited in Bolivia; alluvial, and hard rock or lode deposits. Bolivia produces substantial tin from both types of deposit whereas virtually all Brazilian production to date has been from alluvial sources. Alluvial Deposits Brazil: The alluvial tin deposits of Brazil are located in river channels and flood plains adjacent to low mountain ranges. The terrain containing the tin placers is flat, marshy, and generally jungle covered. The major controls of alluvial cassiterite concentration are the ancient and present stream channels. The average tin concentration in the placers varies from 500 grams to approximately 1.0 kilograms per cubic meter. Tin reserves in the Rondonia field of Brazil have been estimated at 600,000 tons of fine tin. A bucketwheel suction dredge went into production in the Rondonia district in 1979, and four others have since been ordered. Several other gravel pump, and hand mining operations are also in production in this field. In addition to the Rondonia district, tin occurrences are known from Xingu, in Para state, and in the state of Minas Gerais. Bolivia: The alluvial deposits of Bolivia are somewhat more complex due to the variable geomorphology and abrupt topography. Conventional placer accumulations of cassiterite are found in many stream channels and intermontane basins surrounding the major lode tin producing regions. In addition to stream and valley placers, a group of deposits locally referred to as "Pallacos" or "Llamperas" which consist of colluvium, landslide debris and glacial moraine material, contain substantial tin reserves in some areas. The stream channel and intermontane basins contain the only deposits which are presently being exploited by mechanized methods. One dredge is working the stream channel below Cerro Rico de Potosi and another is operating in an intermontane basin southeast of the city of Oruro. Both of these dredges are operated by private companies. The average grade for these operations varies from 250 to 500 grams per cubic meter. The largest of the intermontane basin placers known at present is the Centenario deposit located adjacent to the Catavi lode deposit. This deposit contains approximately 170 million cubic meters of material with an average grade of about 150 grams per cubic meter. The "Pallacos" deposits are found on the slopes of mineralized areas and in glacial moraine. The mineralized material is generally completely unsorted, with tin and sometimes tungsten values distributed erratically throughout the entire mass. Most of these deposits are worked by small leasors or cooperatives; however, at least one mechanized washing plant is in operation southeast of Oruro. The size of these deposits may reach up to several million cubic yards. Grades are very erratic, but may range from 200 to 500 grams per cubic yard. In addition to the formal mining operations, virtually every drainage surrounding the major mines is being worked by independent' miners utilizing hand mining and jig or pan concentration. The aggregate production from these operations is substantial. The

Jan 1, 1982

By Arthur Clark, Terrill

THE Tri-State field is now believed to be the largest zinc district in the world. It has a potential production sufficient to supply the entire zinc demands of the country. It is estimated that a train 70 miles long would be required to haul the district's 1919 output of 60 per cent. zinc concentrates. For many years,, including 1917, Missouri surpassed Oklahoma in zinc production. In 1918, however, Oklahoma led by a wide margin and, in 1919, Missouri produced less than one-sixth of the total for the three states, when Kansas replaced Missouri in second place in the production. The district is now producing one-third of the zinc of the world and twice as much as ever before at the present price.

Jan 1, 1920

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By H. W. Turner

The axis of the middle portion of the Ural mountains is made up chiefly of highly compressed igneous and sedimentary schists, considered of Devonian age by the Russian geologists, with large areas of serpentine (peridotite originally) gabbro, etc,, intrusive in the schist series. In addition there are large areas of probably older granitic and gneissic rocks. The nickel deposits referred to in this paper are found in the Devonian schists and their associated igneous rocks. The gabbro-peridotite intrusions probably took place in late Devonian or early Permian time, inasmueh as the Permian and Carboniferous beds lie at gentle angles on the Devonian series on the west slope of the Urals. Perhaps the first attempt to work a nickel deposit in the Urals was made about 1866 in the Revdinsk district, which is situated southwest of Ekaterinburg. 3 was informed by a Russian that a wet method of extracting the nickel was tried but was not a commercial success. This deposit has been described by Muller,l Foullon, and Karpinski.3 Beck4 gives an abstract of these papers. ; Lying to the southeast of the Revdinsk district, the Sissert estate intervening, is the Verkhne-Ufalei district, which is traversed by the railroad from Ekaterinburg to Cheliabinsk, as shown on the map, Fig. 1, there being a station on this railroad at the iron-smelting town of Verkhne-Ufalci. About 7 versts (4.6 miles) north of this town is the Nijni-Karka-dinsk iron mine, which is a limonite deposit. In one of the shafts in this mine a serpentine rock showing a green mineral was encountered. A sample of this mineral collected in 1910 was tested by Mr. Wyatt, chief chemist of the Karabash laboratory of the Kyshtim Mining Works, and determined as nickel ore. A thin section of one piece of the serpen-

Jan 1, 1915

By N. S. Parate

Detailed analysis is given of the influence of water on the strength of limestone. The mechanism involved in strength reduction is described. Such analysis is of importance in geological, civil, constructional, mining, and metallurgical engineering and is closely associated with the rock mechanics involved in these areas. Mine dumping, slope stability, excavations, sedimentation, etc., are very much affected by the presence of water. Tensile stresses, which have an important role in the development and propagation of fissures, are produced by water in cracks. The development of fissures can be responsible over a long period of time for an ultimate, catastrophic failure.

Jan 1, 1974

By George W. Mansfield

My plan in this paper is, first, to prove three general points, and then to take up the specific applications of the electric motor to nining work. The three poinb are: 1. The electric system is the simplest method known for transmitting and distributing any amount of energy from one locality to another, irrespective of the intervening distance. 2. The electric system with its applications is not in its infancy.

Jan 1, 1888

By Kenneth Robertson

ALL, strangers visiting this district are struck with the peculiar manner in which the pig-iron is graded. There are eleven regular grades, besides which, when gray forge is ordered, one-half of Nos. 1 and 2 Mill are shipped. Occasionally there is another grade Known as Silver Mill, which is made so seldom that I cannot describe it, and have no sample to exhibit. Most of you have found it difficult to grade properly and uniformly under the simpler system which obtains elsewhere, and can consequently readily imagine the increased difficulty with us. Each furnace employs an " expert," and even with this precaution, the system is not conducive, at all times, to amicable relations between buyers and sellers. I am told that it was adopted at the time Southern irons were seeking a market; but it still remains, although the time has come when our iron is sought for and has obtained for itself a place in the markets of the country. The grades are as follows:

Jan 1, 1889

By C. A. Heiland

THE Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station; whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of 100 meters, as under most circumstances it is difficult to level along a larger concentric circle about the station.

Jan 1, 1928