Search Documents

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By A. Weiss, W. A. Coster

Jan 1, 1964

Jan 1, 1920

Jan 1, 1940

Jan 1, 1934

Jan 1, 1941

Jan 1, 1890

Jan 1, 1932

Jan 1, 1892

Jan 1, 1937

Jan 1, 1906

Jan 1, 1905

Jan 1, 1916

Jan 1, 1885

Jan 1, 1888

Jan 1, 1896

Jan 1, 1907

Societies, Boards, Etc , on Which Institute Has Representation United Engineering Society WILLIAM L SAUNDERS, President GEORGE H PEGRAM, 1st Vice-president ALFRED D FLINN, Secretary J V W REYNDERS, 2d Vice-president JACOB S LANGTHORN, Treasurer HENRY A LARDNER, Assistant Treasurer Finance Committee GEORGE H PEGRAM Chairman J VIPOND DAVIES BANCROFT GHERARDI W F M GOSS WILLIAM L SAUNDERS, ex-officio House Committee ALFRED D FLINN, Chairman FREDERICK F SHARPLESS' GEORGE T SEABURYO F L HUTCHINSON CALVIN W RICE

Jan 1, 1923

By N. I. Fisher, J. Shepherd

Statistical studies have been carried out on structural geological data collected across a large zone of roof failure 600 m (1968 ft) wide and at least 800 m (2642 ft) long in the Greta coal seam at Aberdare East Colliery. Two swarms of hundreds of minor, normal faults with throws commonly between 3 and 300 mm in the room and pillar workings are broadly coincident with roof failure. The faults have been classified into dip slip and oblique and strike slip types. Roof conditions have been classified into good; troublesome with subclasses scaly, heavy, gutter falls and wide, flat-roofed falls; and severely failed with subclasses very heavy roof, gutter falls and dome falls. Troublesome conditions are defined as those in which the height of the fall is less than or equal to 0.3 m, and severely failed conditions as those in which the fall height is greater than 0.3 m. Comparison of faults, roof condition and mining rate on a shift basis indicates that faults and roof failure are much more important than machine breakdowns in reducing mining rate. The effect of faults on roof conditions has been quantified using a concept called the "zone of influence," a rectangular area around a fault in which the fault has potentially deleterious effects. The spatial comparison of fault "zones of influence" with areas of roof failure wing Spearman's rank correlation coefficient shows that, while normal dip slip faults do not appear to be associated with roof failure, oblique slip and strike slip faults appear to be associated with roof classed as severely failed. The "zone of influence" of an oblique slip fault may extend up to 3 m on each side of it in the headings and up to 1.14 m in the cut-throughs. The fault "zone of influence" has geomechanical implications for the design of mine openings and Possibly represents the maximum length of a cantilevered roof beam likely to fail during mining, owing to a fault. Roof conditions could Possibly be predicted in blocks of &gin coal if the type of fault could be identified in oriented drill cores.

Jan 1, 1979

By Michael F. Dunn, Francis S. Kendorski

The fall of rock from strip coal mine highwalls continues to be the largest single source of fatal accidents, so methods to improve highwall stability through improved blasting practices were investigated in the field. This paper covers the results of a project to improve, using existing and proven technology, unstable highwall conditions through better blasting practices in Appalachian strip coal mines. Better borehole blasting agent distribution and optimization of burden, spacing, and delay periods allowing satisfactory breakage with minimal backbreak were the objectives. At a selected field site, geologic conditions were closely examined with regard to joint orientation and spacing, and resulting slope stability considerations. Utilizing surface blasting concepts of trying to achieve flexural failure of the rock mass both horizontally and longitudinally by appropriate relationships between burden, spacing, and hole length, as well as delay time sequence to achieve optimal confinement and breakage, successful results were achieved. A test series of eight blasts was completed and the resultant highwall monitored by repetitive photography. Actual blockfalls could be measured and the stability for each blast design thus quantified. The study of drilling and blasting economics along with equipment performance led to an economic model of blast parameters and the identification of blast design cost benefits. The work demonstrated that small strip mining companies are able to achieve a more stable highwall excavation utilizing presently available technology, equipment, and explosive products at improved operational cost and safety.

Jan 1, 1983