Search Documents

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the pegmatites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920's to mine and concentrate cassiterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930's. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant.

Jan 9, 1953

By G. J. Wolga, W. W. Tyler, A. C. Wilson

THE physical properties of uranium have been reviewed by Katz and Rabinowitch.1 Their review includes thermal conductivity data for ternperatures above 375°K. Recently, Mendelssohn and Rosenberg' have published data on the thermal conductivity of uranium from 2" to 20°K. Our measuremerits indicate the temperature dependence of the thermal conductivity in the temperature interval from 20" to 300°K. Electrical resistivity and thermoelectric power were measured on the same sample. The material studied was normal uranium which had been heated at 700°C in a lead bath for 10 min and then quenched in a water bath held at 50°C. From this material a rod M in. in diameter and 2 1/2 in. long was machined. Two 0.040 in. holes were drilled into the rod 1 3/4 in. apart. Copper-constantan thermocouples for temperature and potential measurements were soldered to copper pins which were pressed tightly into these holes. Details of the equipment and experimental techniques used in making the measurements have been described elsewhere." Fig. 1 shows micrographs of a section of the sample studied. Fig. la was taken with unpolarized light and shows impurity inclusions, probably uranium carbide. Fig. lb, showing the same field, was taken with polarized light and gives some indication of the grain size and twinning within the grains. Experimental Results Thermal conductivity and electrical resistivity data are shown in Fig. 2. Table I shows values of

Jan 1, 1954

By Alvin L. Langstaff, Harold D. Raymond

The design of entry systems and mining panels in room-and-pillar oil shale mines seeks to optimize extraction while ensuring both short- and long-term stability of mine openings. Important criteria for optimization include the definition of allowable roof spans and minimum pillar dimensions. Factors considered pertinent to the design of roof spans and pillars are discussed in this paper. They include, but are not limited to, physical properties and grade of the oil shale, depth of burial, presence and frequency of partings and joints and adverse effects of blasting. Also discussed briefly are some of the ventilation and production considerations in mine design.

Jan 1, 1984

By Allan T. Fisk, Carl R. Peterson, Richard E. Brooks, James J. Olson

Development of a continuous drill-and-blast excavation capability in mining and high-speed tunneling has been a long recognized goal. Ideally, a machine to meet the challenge should simultaneously perform drilling, explosive loading, initiation, mucking, ventilation, and other functions while remaining at the face, since the elimination or modification of the cyclic nature of the system would significantly improve the advance rate and economy of drill-and-blast tunneling. The Rapidex continuous spiral drill-and-blast concept, one of the continuous excavation schemes presently under evaluation in the US Bureau of Mines' Bedded Deposits subprogram, utilizes an unusual blasting pattern that provides effective fragmentation and involves a partially self-shielding geometry that permits a lightly shielded machine to remain at the face during blasting.

Jan 6, 1977

By Robert Palmer

So MUCH has already been written on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have, come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place.

Jan 1, 1930

By Frank Hultgren

The influence of grain boundaries and polygonized subsructure on the flow stress of commercially pure aluminum has hem studied. A systematic inz-estigoti017 of grain size and subgrain size and mis-orientation was pursued; the contributions of pain boundary md substruture hardening were found to he additive fuiictions. Subgrain boundaries exert greater influence on hardening at room temperature than do grain boundnries. Both subgrain diameter and misorientation influence flow stress, but only to the extent that both contribute to the dislocation density. The flow stress due to substructure may he described by the equation of = abp1/2. THE origin of substructure hardening in metals has remained unclear for a long time. Lately, both theory and experimental techniques have become more exact and merit a closer examination of the subject. In the present work, the influence of polygonized substructure size and misorientation in commercially pure aluminum on mechanical properties has been systematically investigated. The influence of substructure on mechanical properties has been compared with that of grain boundaries. In addition, the works of several authors are compared with theoretical predictions of substructure hardening. EXPERIMENTAL TECHNIQUES Aluminum of 99.9 pet purity (0.04 Fe, 0.046 Si, 0.00 Cu) was employed. Various grain sizes were produced by heavy (over 90 pet reduction in area) cold drawing and recrystallization at various temperatures. A (111) fiber texture was observed in all specimens. Grain sizes were analyzed statistically. Substructure of varying size and misorientation was produced by prestraining specimens of various recrystallized grain sizes. Specimens for mechanical testing and substructure analysis were recrystallized, prestrained, and annealed together. The samples were prestrained from 5 to 25 pet in tension at room temperature and annealed at 200" to 370°C for 2 hr. All samples were rapidly cooled (in air) from the anneal to retain the subgrain wall structure developed at the annealing temperature. A clearly polygonized substructure was developed in all cases. Substructure size was measured by the Berg-~arrett' technique and analyzed statistically. Substructure misorientation was measured in the following manner. Individual grains in the polycrys-talline aggregate were isolated and their intensity distributions mapped using an X-ray goniometer and Geiger counter. From the observed profiles, the

Jan 1, 1964

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6' ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By Bashir Ahmed, Fred D. Wright

Numerous investigators have studied the various factors that influence the ultimate strength of model mine pillars, such as ratio of height-to-least width; restraint or friction on the top and bottom; 1,2 the effect of stress distribution in pillars on their strength;3 and the scaling factors involved in applying the results of model pillars to full-scale pillars. However, the load-bearing capacity of pillars after initial failure does not appear to have been investigated. Yet many mines employ methods in which small pillars or pillar remnants are left systematically; these pillars crush as mining progresses and, of necessity, affect the behavior of surrounding rock even after initial failure. The effect of such crushed or crushing pillars depends largely on their load-deformation characteristics. This chapter presents the results of a preliminary investigation to determine the load-deformation characteristics of a few model mine pillars to and beyond initial failure. Various investigators have also studied the elastic and viscoelastic behavior of mine structures. In such studies, computers are frequently employed to obtain numerical results by the finite difference or finite element methods. It would be entirely feasible to write a program that would approximate the load-deformation characteristics of pillars to and beyond the crushing stage if these characteristics were known. More accurate information on the induced stresses and deformations in overlying strata and on surface subsidence could be obtained, information which should result in better strata control by enabling the engineer to calculate more accurately the effects of changes in pillar spacing, size, and shape.

Jan 1, 1972

By Walter R. Hibbard

ALTHOUGH extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110), [III] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampon5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr s in a standard mercurous nitrate test. Edmunds 12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wassermann reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. PREPARATION OF SPECIMENS Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5,10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. DETERMINATION OF POLE FIGURES A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pct nitric acid to 0.0015 in. thickness and (III) pole figures were determined using copper K-alpha radiation in the manner described by Brick.1 The three general types of pole figures

Jan 1, 1947

By C. A. Crawford

Nickel and the nickel-copper alloy, the latter generally referred to as monel metal, are available in a variety of wrought and fabricated forms, of which the following are regular commercial products:

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 8, 1979

By O. N. Carlson, D. G. Alexander

THE hardness anisotropy of metals and alloys has been of increasing interest in recent years but silicon ferrite,1 niobium,2 and tungsten3,4 are the only bcc metals about which this type of information has been reported. This investigation was carried out on vanadium and chromium single crystals in an effort to determine to what degree the hardness variations observed in these metals are due to orientation effects and to compare their behavior with other bcc metals. In earlier work the authors had observed a small angular dependence in the Diamond Pyramid Hardness of single crystalline vanadium on the (100) plane but no anisotropic effects were noted on either the (110) or (111) planes. At the suggestion of R. G. wheeler5 it was decided to investigate this effect in greater detail using the more asymmetric Knoop indentor. The vanadium metal used in the study was prepared by the aluminothermic reduction of V2O5 followed by electron beam melting.6 The principal analyzed impurities were 230 ppm C, 230 ppm O, 65 ppm N, 90 pprn Al, Cr not detected, 50 ppm Fe, 60 ppm Ni, and 200 ppm Si. The chromium was an iodide-refined product obtained from the Chromalloy Corporation. Analysis of this material showed the following amounts of impurities present: 10 ppm C, 9 ppm O, 2 ppm N, 0.4 ppm H, 3 ppm Al, 2 ppm Ca, 2 ppm Cu, 20 ppm Fe, 1 ppm Mg, 0.3 ppm Mn, 1 ppm Mo, 3 ppm Ni, 10 ppm Si, and 1 ppm V. Single crystals of both metals about 1 cm in diam and 10 cm in length were grown by an arc-zone melt- ing technique.7 The chromium crystal was annealed at 1600°C for 6 hr in a purified argon atmosphere to remove any strains or inhomogeneities, but the vanadium was tested in the as-grown condition. The crystals were oriented by the Laue back-reflection method and then sectioned with a spark cutter into individual specimens with a (loo), (110), or (111) plane parallel to the crystal surface. They were mounted in Lucite and carefully ground to a flat surface. The vanadium specimens were then electropolished in a 6 pct perchloric acid-methanol mixture while the chromium specimens were mechanically polished on a Syntron vibratory polisher using an alumina abrasive. The orientation of each crystal was then rechecked by the back-reflection X-ray method. All of them were found to lie within 2 deg of the desired orientation with the exception of the (110)-Oriented chromium crystal which was within 4 deg. Microhardness impressions were taken at 10 deg intervals from the common (110) direction by rotating the crystal in the plane of the crystal surface. A Knoop indentor was used with a 400-g load on the vanadium crystals and an 800-g load on the chromium. The hardness values are averages of 6 impressions and standard deviations were calculated for each set of data. The values reported for the (111) plane of vanadium are based on from 10 to 15 measurements for each point. The microhardness results for vanadium and chromium are plotted as a function of the angular rotation of the long axis of a Knoop indentor from the (110)

Jan 1, 1970

By Charles Bohdanowicz

Production of crude in 1937 decreased (Tables 1 and 5) by about 2 per cent, while gas production for that period increased by about 6 per cent after a slight decrease in 1936 (0.4 per cent).' As in preceding years, drilling operations were confined principally to extensions of old oil fields in the Jaslo district (fields 1 and 7) and to some extent to such extensions in the Stanislawbw district (field 27). Deepening of old wells to horizons reached more recently by new wells gave on the average better results per well than those attained by new wells (Table 3). Reserves of proved lands have increased some by new oil fields discovered, Targowiska (field 8) and Czarna (field 19) both of which, however, have only small production. The Daszawa gas field (field 25) has not been extended, but two new gas fields were located instead— Opary, distant 25 km. (151/2 miles) northwest of Daszawa, Balicze at 12 km. (7 1/4 miles) southeast of Daszawa, and Kalusz (TESP Company exploiting potassium salts) in the vicinity of the town of that name (field 33). Drilling upon the gas area near Tarnbw and Debica, while gas-bearing sandstone had been found at depths of from 300 to 512 meters (984 to 1680 ft.) (Zdziary No. 2) and at 220 m. (722 ft.) [pressure 11 atmospheres, flow 24 cu. m. per min. (847 cu. ft.)] (Przyborbw No. l), has not as yet ascertained horizons qualified for permanent exploitation. The exploring well near Kos6w remained for the last seven months at the depth of 1420 m. because of the collapse of rotary drilling pipe. Below the 300-m. level no gas sands have been encountered at this well. Gas Reserves In connection with the broad plan of developing industrially the sector of Poland lying between the Vistula and the San Rivers, and extending farther north as far as the city of Radom, there arose the necessity of a more accurate calculation of gas reserves for the fields of

Jan 1, 1938

By L. L. McDaniel

DURING the past few years a number of improvements in smelting and power equipment have been made at the Douglas smelter of the FIG. 1.-GENERAL PLAN OF SMELTER. Phelps Dodge Corporation at Douglas, Ariz. In the summer of 1935 work was started on the first unit of a new reverberatory waste-heat boiler plant which ultimately was to furnish steam for a modern high-pressure power plant. A second reverberatory waste-heat boiler unit

Jan 1, 1939

By W. B. Agocs

In August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model I1 total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey.

Nov 1, 1955

By Frank C. Greene

Drilling in Missouri in 1944 was nearly treble the rate of 1943 because of continued development of the Tarkio pool in Atchison County and the preparation of a pool in Jackson County for a water-injection project. The pipe line from the Prairie Point gas pool in Platte County was in operation throughout the year of 1944, but several of the shallow oil pools in Cass and Jackson Counties were off production during much of 1944 because of a shortage of help. Table I gives a summary of activities by counties. The total footage drilled was 41,475 .ft., of which 21,187 ft. was by rotary tools and 20,268 ft. by cable tools.

Jan 1, 1945

By Richard A. Boulay

The effects of capital, operating and debt cost variations on project performance criteria are examined using a theoretical model and an actual case history. On an after-tax basis, financial measurements are found to be most sensitive to operating cost changes, somewhat sensitive to reasonable changes in capital costs and relatively insensitive to interest rate fluctuations.

Jan 1, 1985

By Jack White

This paper gives details of the results of careful testing carried out on two types of ball mills, conical trunnion overflow and cylindrical grate discharge, on identical ore. The object of the test work was to determine which ball mill was the most economical to install for future extensions to the Mufulira concentrator.

Jan 1, 1950

By H. N. Hickey

Wildcat drilling operations in Montana during 1933 did not yield any discoveries of oil or gas that were of major importance. There was comparatively little drilling in the older proven fields, as most of the interest was centered in the Cut Bank field, where 44 wells were completed. The total number of wells completed in the state during the year was 79, of which 62 were productive of either oil or gas.

Jan 1, 1934

By F. H. McDowell

For more than two hundred years Mexico has been enriching the world from her inexhaustible wealth of precious metals. From this source alone, over three thousand five hundred millions of dollars have been poured into the coffers of Europe and America. During these centuries the wants of the country in manufactured goods have been supplied from the mills and machine-shop of the Old World. English, French and German merchants in Mexico have vied with each other in their efforts to control the importing of these goods from their respective countries. The overthrow of Maximilian, the departure of the French and the restoration of the Republic, largely influenced by the strong stand taken by the United States Government during our own civil war, established a new order of things. Americans were encouraged to visit the sister republic, examine into the needs of the country, as well as its resources, and interest themselves in the work of development. More recently, under Presidents Diaz and Gonzales, liberal inducements have been extended to American capitalists to build railroads, open mines, erect reduction-works, raise cattle and improve the crude systems of agriculture. The Mexican Central Railway has been pushed south from the Rio Grande to the Capital, and, by its branches and connections, makes the whole mineral belt of the country accessible.

Jan 1, 1885