Search Documents

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By Arthur Phillips, R. M. Brick, A. J. Smith

A previous publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl². A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic defomation or cracking has been considered in relation to the physical properties of the alloy On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degrec of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. Strain in Solid-solution Alloys A 10 per cent magnesium alloy ill the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using alllminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl², CaC12, NaCI. Chill-cast rods were sealed under vacuum in Pyrex glass, homogenized several days at 450' C., air-cooled and machined to rods of from 1/8 to ¾-in. dia. Metal powders taken from these rods with a fine-toothed saw were again sealed under vacuum in

Jan 1, 1935

By R. M. Brick, Arthur Phillips, A. J. Smith

A previous publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl². A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic defomation or cracking has been considered in relation to the physical properties of the alloy On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degrec of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. Strain in Solid-solution Alloys A 10 per cent magnesium alloy ill the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using alllminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl², CaC12, NaCI. Chill-cast rods were sealed under vacuum in Pyrex glass, homogenized several days at 450' C., air-cooled and machined to rods of from 1/8 to ¾-in. dia. Metal powders taken from these rods with a fine-toothed saw were again sealed under vacuum in

Jan 1, 1935

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By J. J. Pavlica, I. Iwasaki

Grinding in steel milk adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and galmic current measurements were made on electrode combinations of pyrrhotite-mild steel and pvhotite- stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles cawed slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1983

By Austin Park

More metal at a lower profit continued to be demanded from the mining industry during 1969. Correspondence with U.S. and Canadian mining districts and a study of the mining literature indicate that, a large majority of the mines are keeping pace and rising to the challenge. Continued research and better understanding of pneumatically applied concrete for roof and wall support was of top interest. Many mines are changing mining methods for the adaptation of load-haul-dump units. The most recent adaptation being the use of these units in cut- and-fill stoping and in various types of development headings. Boring methods and use of two- or three- boom drilling jumbos mounted on rubber tires for versatility continues to be the favorite approach to the demand for rapid excavation.

Jan 1, 1970

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.' Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method' was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.' Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By Thomas A. Earl

Much of the strip mining in the Appalachian coalfields was done prior to backfilling and regrading requirements, resulting in many devastated areas which also have serious acid mine drainage problems. Economic incentive or justification for reclaiming these thousands of acres of land does not exist unless some value can be attached to the open cuts and weathered overburden piles. In Pennsylvania many of these old strip mine cuts are being successfully used for sanitary landfills and sludge disposal sites, and multiple benefits are realized. Given proper regulatory control, this technique could be beneficially applied to many other areas in the east.

Jan 1, 1977

By F. W. von Batchelder

The principles of microradiography and their application practically coincided with the discovery of X-rays. These principles were first used in the metallurgy field by Heycock and Neville1 in a study of the dendrite structure of alloys of Au-Na, Au-A1, Cu-A1, and Ag-A1. The method was introduced in the USA by clark2 after a visit to France. Scores of papers have been written, and a very complete bibliography on this subject was compiled by the Eastman Kodak company. Although a number of papers have discussed X-ray

Jan 1, 1959

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulageways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By C. A. Stetefeldt

In May and June, 1885, I was engaged in examining the goldores of Las Minas, in the State of Vera Cruz, Mexico, with a view of finding a cheap and efficient method for extracting the gold. The following minerals could be plainly seen in the ore : magnetite, pyrites of iron, pyrites of' copper, quartz, and garnet. Neither galena nor zinc-hlende mere visible, but the ore contained a trace of lead, and in some samples of ore from the Muertos mine, 1.19 per cent. of zinc mas found. Antimony and arsenic were not present. Native gold could scarcely be seen in specimens of' the ore, and it only appeared—mainly in extremely fine particles—after pulverizing and washing. Magnetite was in every instance the most prominent mineral, its quantity varying between 43 and 67 per cent. Determinations of copper and sulphur showed that from 3.5 to 7 per cent. pyrites of copper, and from 3 to 22 per cent. pyrites of iron were present. The gold-value of the ore varied between 0.3 oz. and 0.8 oz. per ton. I do not speak of specimens, but of average samples of large quantities of ore put through the battery. In ore that had been crushed through a No. 40 screen, the gold appeared, in part, as free gold, the rest being thoroughly mixed with the magnetite and pyrites, both minerals containing about the same percentage of gold. If this free gold was brought in contact with pure quicksilver it (lid not amalgamate readily, even if the quicksilver was charged with sodium amalgam.

Jan 1, 1886

By A. G. Moncrieff

In the paper the authors show [(Fig. 12)] in diagramatic form a "typical vacuum filtration system." This indicates a drum filter with two filtrate receivers-one for mother liquor and one for wash liquor. Have the authors ever found a drum filter that will adequately separate mother liquor from wash liquor? I recall in about 1957 being superintendent of a major copper leaching operation treating oxide flotation concentrates. The plan was being expanded, and filters installed to replace CCD following acid leaching and primary thickening of the pulp. The design of the expansion allowed the mother liquor to join the thickener overflow as feed for the electrolytic tankhouse. The water balance required that only pan of the wash liquor could be electrolysed direct, and the remainder had to be treated by lime precipitation. The design assumed the mother liquor would have the same copper content (about 50 gpl) as in the leach pulp solution, and the wash liquor about 50% of this (25 gpl from memory). You can imagine my horror when, on starting up, the solution from the mother liquor receiver contained somewhat under 40 gpl and, from the wash liquor receiver, somewhat over 40 gpl. The filters were provided by two of the most reputable manufacturers and, in the end I believe they agreed that never before had they supplied rotary drum filters that would segregate the filtrates. By changes to the valve design we made minor improvements, but eventually decided that insufficient segregation of the filtrates was possible to warrant trying to do it. On further consideration I concluded that, owing to the time delay between solution passing through the cake and entering the valve, segregation was impossible, though radical alteration of the internal piping of the filter might have improved it. I would be interested to know if anyone has found a solution to this problem using a drum filter. If not, why go on publishing information that infers that it is possible?

Jan 1, 1982

By J. J. Knoerzer

A full-scale operational test was conducted on the Coaltek preheating and pipeline charging system at the Semet-Solvay Div. of Allied Chemical at Ironton, Ohio, for the purpose of determining whether a high-quality blast furnace coke could be made from blends containing at least 75% Illinois No. 6 Coal and at the same time reduce air pollution during the charging of the ovens. The coke produced had similar physical characteristics as compared to our conventional wet-charged coke, with the exception of smaller size for the preheat coke. Air pollution during charging was con- trolled and there were no serious operating problems. The coking time was reduced 25% from our normal 17 hr for wet charging to 12.8 hr for preheated charges. The blast furnace performance with preheat coke was satisfactory.

Jan 1, 1976

By K. Osseo-Asare

LIX63 In combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 10 Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX 63 and DNNS Increasing LIX63 concentration retards both extraction and stripping rates while DNNS has the opposite effect. Slope analyses of equilibrium data Indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1981

By Earl A. Gulbransen, Kenneth F. Andrew

DRY oxidation of zirconium has been studied by several groups.'" The present work extends our early study1 to the high-temperature studies of Cubicciotti2 and Belle and Mallett.8 ulbransen and Andrew1 showed that the parabolic rate law fitted the 2-hr experiments between 200" and 425°C after an initial deviation. An energy of activation of 18,200 cal per mol was calculated. Cubicciotti,' in a study between 593" and 880°C, showed that the parabolic rate law fitted the data and an energy of activation of 32,000 cal per mol was calculated. In contrast to these studies on sheet specimens, Belle and Mallett3 studied the oxidation reaction on rod specimens and found a cubic rate law to fit the data.

Jan 1, 1958

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919