Search Documents

By Eugene A. Stephenson

In November, 1932, Dr. Lacey, of the California Institute of Technology, presented before the American Petroleum Institute some of the results of his research under Project 371. The investigations described dealt particularly with changes in the physical properties of petroleum that result from the solution of natural gas therein. The solubility of Santa Fe Springs dry gas, containing 87 per cent methane, 8 per cent ethane and 5 per cent propane, had been determined in various crudes at 100' F., and 2000 lb. pressure per square inch as shown in Table 1 and Fig. 1 herewith. Originally the computations were made in terms of cubic feet per barrel, but' for a more uniform basis of comparison the results are also shown as cubic feet of gas2 per cubic foot of oil.

Jan 1, 1935

Jan 1, 1917

Table

Jan 1, 1910

Jan 1, 1894

Jan 1, 1887

By Francis M. Rice

Before the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By Francis M. Rice

Before the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By R. J. Lytle, E. F. Laine

The in situ high frequency electrical conductivity and permittivity of Colorado oil shale were recently measured. The measurements were made at 45 MHz (45 million cps) by transmitting from one borehole to two receiving boreholes, all boreholes in line. A differential measurement using the received signals was used to calculate the conductivity and permittivity.

Jan 1, 1983

By Benjamin Smith Lyman

It has seemed that it might be a highly useful contribution to the study of structural geology to assemble, in as compact a form and on as large a scale as practicable, a great number of

Jan 1, 1896

By W. C. Winegard, C. J. Simpson, C. J. Beingessner

VARIOUS organic compounds, such as borneol, carbon tetr a bromide, and hexachloroethane, solidify as transparent plastics with a fcc structure. Each of these substances undergoes a solid-state transformation from the plastic phase to a brittle phase at temperatures slightly above 20°C. Since it was known that these plastic crystals solidified like metals,1 it was decided to investigate the possibility that solid-state grain growth would occur in the same way as it does in metals. Two-dimensional grain growth in thin films of plastic organic compounds has been studied with the aid of cinemicrophotography. Samples varying in thickness between 250 and 1000 @ were prepared by subliming a thin layer of the compound onto a microscope slide plate which was then covered with a second slide plate.

Jan 1, 1968

W. M. Courtis, Detroit, Mich.: Except for free-gold ores, I have always believed in scorification. I think the crucibleassay gives silver low. We found this out at the Wyandotte works in assaying Silver Islet ore. The mine-managers made us, and also the check-assayera, run one of the duplicates by

Jan 1, 1896

By J. A. Herbst, K. Rajamani, M. Siddique

This paper presents an investigation of the accuracy of population balance model predictions for ball mill scale-up. Experiments performed in 25.4 x 29.2 cm (10 x 11.5) batch mill are used to estimate linear grinding rate parameters that, in turn are scaled according to specific power draft to predict performance in 381 x 292 mm (15 x 11.5 in.) and 762 x 457 mm (30 x 18 in.) batch and continuous ball mills, respectively. Results are presented for wet and dry grinding of two homogeneous solids, limestone (soft) and quartz (hard), and one heterogeneous solid, a complex molybdenite ore. In all cases good agreement between predicted and experimental product size distributions was obtained.

Jan 1, 1983

By Frank C. Schrader

Page Introduction.............................. 196 Geology of the District......................... 196 Ore Deposits of the District....................... 198 Gcncral Description........................ 198 The Cerbat Mountains Group................... 199 General Description...................... 199 Tennessee Mine....................... 203 Midnight Mine........................ 203 Mineral Park........................ 204- Golconda Mine........................ 204 Other Ore-bearing Districts.................. 205 Lost Basin District ...................... 205 The Black Mountains Group.................... 206 Tom Reed-Gold Road District...................... 208 General Dcscription........................ 208 Development........................... 209 Topograplly............................ 210 Geology.............................. 210 Ore Deposits........................... 213 General Dwcription...................... 213 Zones.......................:....215 Structure of Ore Shoots.................... 217 Gold Road Mine ......................... 218 General Description...................... 218 Geology........................... 218 Ore Deposits......................... 219 Tom Reed Minc......................... 222 General Description..................... 222 • Ore Deposits.......................... 222 Development......................... 223 Character of Ore....................... 224 Other Mines........................... 224 Fields Similar to the Ton1 Reed-Gold Road District......... 227

Jan 1, 1917

By B. H. Bergstrom, W. Mitchell, C. L. Sollenberger

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) and D. A. Sullivan, Jr. (with the University of California) — Messrs. Bergstrom, Sollenberger and Mitchell have shown in two excellent papers that the energy per unit mass required for the breaking of spheres is inversely proportional to the size modulus of the fragments of the broken spheres. They found that the fragments of spheres broken within a steel enclosure were finer than those produced by breaking spheres encased in gelatin. This results from utilization of part of the strain energy at fracture for secondary breakage. For spheres not encased in gelatin, these authors found that after fracture the fragments of the spheres possess kinetic energy amounting to 45% of the strain energy needed for initial fracture. Breakage of a sphere in gelatin results in waste of this kinetic energy, whereas breakage inside the steel container makes use of this kinetic energy for further size

Jan 1, 1962

By A. H. Jones, J Leasia, S. J. Green, R. D. Perkins

Previously, two groups have conducted studies in order to define the influences of the intermediate principal stress. Mogi studied biaxial compression on prisms of Dunham dolomite and concluded that the intermediate principal stress should be taken into account. His study showed that failure strength increases with increasing [02], but less than the strength increase with increasing confining pressure. Handin, Heard, and Mogouirk's study on cylinders of Solenhofen limestone in torsion also found that the strength depends on the magnitude of [02]. More recent investigations by Mogi varying all three principal stresses independently and by Wawersik varying two of the principal stresses independently provide more detailed data confirming the effect of [02] on failure. All these tests were at low strain rates, and only the work of Wawersik reports measurement of all strains. The investigation here measures axial and transverse strains and included uniaxial and triaxial stress compression tests and biaxial stress tests using tubular samples (axial load and internal or external fluid pressure) at strain rates to 103/sec to provide the stress-strain response and to define the maximum stress or yield locus of Solenhofen limestone and Westerly granite.

Jan 1, 1971

WALTER N. CRAFTS,* Toronto, Canada (written discussion?).-During the forging of 9.2-in. shells -for the United States Army, it was noticed that better results were obtained in certain instances when test bars had been held sometime before pulling. An investigation, therefore, was made by our metallographer, Mr. F. M. Arnold, to determine the effect of seasoning. The forging consists of a single operation, piercing a solid cast blank. The test sections were cut from the walls by an oxyacetylene flame, one piece from the nose end and one from the base on the opposite side. The test pieces were not heat treated in any way and the tests and seasonings were carried on at normal atmospheric temperatures. The specifica-tions were as follows: Standard 2-in. test bar, 0.505 in. in diameter; elastic limit, over 19 long tons, or 42,500 lb.; ultimate stress, 39.6 to 49.1 long tons, or 87,500 to 110,000 lb. per sq. in.; elongation, over 13 per cent. As a preliminary test two heats were selected; BP555, which was tested and reported failed on elongation on Aug. 20; and B01771, which was tested and reported failed on Aug. 24. On Aug. 29, retests were cut and machined from the same shells and held till Sept. 3 (5 days) when they were pulled. Both sets of results are given below.

Jan 12, 1919

Jan 1, 1918

Jan 1, 1916

By Robert A. Brusca

OUTLINE Mineral Poor, but great primary inputs Net importer of most primary inputs • Copper • Zinc • Aluminum • Oil Problems for Japan • Supply Disruption • Currency Swings Remedies • Yen pricing of primary products • Long term contracts • Ownership of primary commodity producers Current Approach No Text Available

Jan 1, 1990

By T. F. Witherbee

THE following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

Jan 1, 1877