Search Documents

By C. R. Kuzell, G. H. Wigton

Knowledge of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is frequeqtly called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat in accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers, etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any modern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases. - The calculation of sensible-heat capacities1 from specific-heat equations is a comparatively long and tedious operation. This is especially

Jan 1, 1915

By J. D. Miller, M. B. Mooiman

It has been discovered that gold can be extracted from alkaline cyanide solution with primary, secondary, and tertiary amines by adding certain Lewis base modifiers, such as organic phosphorus oxides. Under these circumstances, gold can be extracted at about pH 10, commensurate with the pH of cyanide leach liquors. The selectivity of the amines and amine/modifier combinations for Au(CN)[2] over other metal-cyanide complexes is discussed. Potential applications for the solvent extraction of gold from cyanide solutions are also discussed.

Jan 1, 1985

By J. B. Cheatham, R. B. Paslay

Rock stresses and steady-state flow rates induced by the pressure gradient associated with the flow of formation fluid into a borehole have been analytically determined for a permeable, elastic material saturated with an incompressible fluid. In this analysis, the material properties and loading are considered to be symmetric about the axis of the borehole and independent of axial position. For Case I the material is assumed to have uniform permeability in the radial direction, whereas for Case 11 the permeability is assumed to have been reduced in a localized region adjacent to the hole by either normal well completion and production operations or deliberate plugging during air drilling. Results of a numerical example indicate that, in the absence of plugging, the rock shear strength must be approximately two-thirds the formation fluid pressure in order to prevent rock failure. The required rock strength is high for small radial zones of plugging and decreases as the region of reduced permeability becomes larger; however, a depth of plugging can be reached beyond which there is no real gain in strength, although the flow rate can be further reduced. INTRODUCTION During normal production of oil from a well, it is often desirable to increase the production rate of the formation fluid by increasing the pressure gradient through the formation adjacent to the borehole. Depending upon the magnitude of this pressure gradient and strength of the rock material, this production-rate increase can cause sloughing of the hole wall. In many cases, the production - rate increase can result in excessive sand production, increased wear of production equipment, lost production time and expensive workover jobs. In addition, the phenomenon of increased rock bit penetration rate with the use of a gaseous instead of a liquid drilling fluid has been observed in oilfield drilling operations and experimentally demonstrated by various investigators for several years. The improvement obtained by employing this technique can be quite significant and offers apromising method for reducing drilling costs. However, air drilling is currently limited to geographical locations where high-capacity water-bearing formations are not encountered. This limitation has prevented widespread adoption of air-drilling techniques, because the water influx into the borehole interferes with efficient removal of the drilling cuttings and usually results in a condition such that the bit becomes "balled-up" or stuck in the hole. In an attempt to remove the water - intrusion limitation from air drilling, various chemical and mechanical water shut-off methods have been proposed. Goodwin and Teplitzl suggested one such proposal whereby the permeability of the water-bearing rock structure was reduced in the vicinity of the borehole. Although the development of a shut-off method based upon this approach would certainly be welcomed by the oil industry, it is conceivable that, under certain conditions of the pressure gradient, strength of the rock material and depth of the modified permeability zone, a stress field can be created that will result in an unstable hole. As part of their study, an analytical solution is given for stresses in an idealized model of a hole and the surrounding rock material. The purpose of the present study is to extend the analysis of Goodwin and Teplitz to gain more insight into the details and consequences of excessive production rates and formation water shut-off. In particular, simplified models of these problems have been analytically examined, which makes possible the evaluation of the type of stress fields that can be anticipated as a result of these production and drilling practices. Both problems solved concern the determination of the steady-state volume flow rate of the formation fluid and the resulting steady-state stress and displacement distribution in a hollow, cylindrical configuration. The cylinder of Case I, corresponding to the production-rate problem, consists of a material with a constant permeability from the inside surface to the outside surface; the cylinder of Case 11, corresponding to the water shut-off problem, consists of a material with a constant permeability from the inside surface to an intermediate concentric cylindrical surface and a second constant permeability from the intermediate surface to the outside surface-

ZAY JEFFRIES,* Cleveland, Ohio (written discussion?).-The microscope has, indeed, proved a mighty tool in the study of the structures of substances. It is limited in its resolving power to the wave length of the light used for illumination. A little in resolving power can be gained by using ultraviolet rays, which can only be detected by the photographic plate. Even the highest powered microscope only permits the study of aggregates of millions of atoms. The x-ray spectrometer, on the other hand, makes it possible to study the positions of the atoms in a crystal. The positions of the atoms in over fifty crystals have now been ascertained. But in amorphous substances the x-ray spectrometer is only able to tell us that the atoms seem to have no regular arrangement; the actual arrangement and method of grouping is still a mystery. In most perfectly formed crystals and in so-called "grains" in metals, the x-ray spectrometer teaches us that colloids seem to play no role inasmuch as the atoms are arranged in regular layers rather than in random clusters. In the boundary region between crystalline grains of like as well as unlike substances and in amorphous substances like glass, it seems probable that the random clusters, or colloids, play an important role. There still remains the application of wave lengths connecting the ultraviolet and x-rays both by direct reflection or diffraction and by the ultramicroscope. In the study of substances like glass, for example, it may be possible to identify the clusters or molecules by one wave length and to study the positions of the atoms in a cluster by using a smaller wave length. Any light that can be thrown on this important unknown subject and its relation to the properties of substances is therefore very welcome, and Mr. Alexander's paper is so written as to stimulate thought and experimentation in this direction. JEROME ALEXANDER (author's reply to discussion ?).-Col. Bancroft states' that in the case of alloys, the mass is always crystalline. While this generally may be so in the case of alloys, as ordinarily met with, before the alloy reaches this state or condition, its constituent particles must be in a still more finely dispersed state. In alloys, the speed' of transition between the finely dispersed state where the phases are amorphous, and the crystalline state where the phases are of known composi-

Jan 5, 1919

By Carl G. Schwenk

Rocks of the Precambrian Shield of Rusk County, Wis., were recognized as a favorable host for volcanogenic base metal deposits by personnel of Bear Creek Mining Co. Most of the county is covered by a thick layer of glacial drift: consequently, geophysical techniques played a prominent role in the exploration program conceived and initiated there in 1966. The original work on three Precambrian exposures was followed by an airborne electromagnetic survey and subsequent ground follow-up. A geophysical evaluation of air-borne anomaly F-22 defined a target which was interpreted as a massive sulfide body. Numerous potential field and electrical tools were utilized to describe the geometry and physical properties of the target. Drilling confirmed the massive sulfide interpretation and eztentually outlined a 6 million-ton copper deposit.

Jan 1, 1977

By R. W. Fountain, John Chipman

The solubility of nitrogen in Fe-B alloys (0.001 to 0.91 pet B) is determined by the Sieverts' technique for temperatures of 950° to 1150°C. The activity coefficient of nitrogen is decreased by boron. The three-phase equilibrium between ? iron, BN, and gas is established and also the four-phase equilibrium between iron, BN, Fe2B, and gas. The above equilibria are calculated for a iron. The relation of these data to hardenability and strain aging of boron-treated steels is discussed. BORON additions are known to enhanbe the hardenability of heat-treatable steels and to assist in the control of strain aging in sheet steel for deep drawing. The increase in hardenability is explained by the theory that adsorption of boron on austenite grain boundaries reduces their free energy and thus retards ferrite and upper bainite nucleation.l,2 Digges and Reinhart3 have shown that the full effectiveness of boron in commercial steels is achieved only when strong nitride formers such as titanium and zirconium are also present. The influence of nitrogen on eliminating the boron contribution to hardenability was also demonstrated by Shyne and Morgan.4 These workers prepared Ni-Mo steels containing either nitrogen or boron or nitrogen plus boron. The nitrogen-plus-boron steels showed the lowest hardenability which was attributed to the presence of stable nucleating particles, presumably nitride. Morgan and Shyne5-7 have shown that boron in the amount of 0.007 pet will completely eliminate strain aging due to nitrogen in low-carbon, open-hearth steels. In addition, by proper control of the boron additions, a rimming steel can be produced. Since the effectiveness of boron on hardenability and eliminating strain aging is influenced by the amount and distribution of the nitrogen in the steel, the present study was. undertaken to determine the influence of boron on the solubility of nitrogen in iron. EXPERIMENTAL PROCEDURE The solubility of nitrogen in Fe-B alloys was measured by the method of Sieverts, which consists of determining the amount of gas dissolved by the metal in a constant volume system. The apparatus employed in this investigation and the experimental details have beendescribed previously.B AMcLeodgage was added to the apparatus to allow measurements at very low pressures. The alloys were melted at reduced pressure in a basic-lined induction furnace using electrolytic iron and ferroboron. Ferroboron was added after the primary deoxidation of the iron with carbon. Since it was difficult to attain a constant low level of oxygen by this procedure, silicon was added after the carbon deoxidation and prior to the ferr obor on addition. The alloys were castas 2-in. sq ingots, heated in argon at 1050loC, and forged to 1/4-in. plate. After forging, 1116 in. was machined from each side of the plate to remove any possible contamination, and it was then cold-rolled to 0.010-in. sheet. The sheet was cut into approximately 1/4-in. squares and pickled in an inhibited H2SO4 solution to ensure a clean surface. In the case of the boron alloys, a hydrogen treatment could not be used for surface cleaning because boron losses resulted. The composition of the alloys is given in Table I. For a solubility determination, a 75-g sample was inserted in a quartz tube and sealed in place in the apparatus. The entire system was evacuated at room temperature and leak tested for 24 hr. If no leaks were observed, the system was heated to the temperature of measurement and again leak tested for 24 hr. If no leaks were detected, the hot volume and solubility determinations were begun. The hot volume was determined at a constant temperature for each run by admitting successive amounts of argon and recording pressure vs volume, which, in all cases, resulted in a straightline relationship. The argon was then removed and the procedure repeated with nitrogen. Successive additions were made until the desired nitrogen content of the metal and equilibrium pressure of the system were obtained. The

Jan 1, 1962

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By J. T. Hayward

Studies of the forces and conditions governing the recovery of petroleum from natural reservoirs indicate that a low gas-oil ratio increases ultimate recovery, retards the encroachment of water and tends to reduce lifting costs. Methods for controlling and reducing gas-oil ratios in producing wells consequently have been given considerable attention during the past few years. However, during this same period, the production from wells in nearly all fields has been fixed by proration agreements and it is the opinion of the writer that where a well is required to produce steadily at a predetermined rate, less than its "potential" or maximum capacity, the gas-oil ratio will depend only upon the rate of production, and will be independent of the method of production and of the design of equipment in the well. If no change in the rate of production is contemplated, efforts directed to improving the gas-oil ratio by altering the diameter of the flow string, changing the position of the choke, assisting the flow with gas-lift or pump, etc., will be unsuccessful. This viewpoint is not new. It was presented by H. N. Marsh and B. H. Robinson in 1929,' but it has not been generally accepted. Although engineers believe that the rate of withdrawal and not the equip ment used governs the water-oil ratio, a similar opinion regarding the gas-oil ratio is not so commonly admitted. The rates of flow of oil and gas into the base of an oil well depend upon the following conditions: 1. The characterist-ics of the oil and gas. 2. The characteristics of the underground reservoir. 3. Temperature and pressure conditions in the reservoir. 4. The back-pressure held against the face of the sand. In operating a well, the only one of these conditions over which control may be exercised through operating procedure and the use of equipment above the sand is the back-pressure at the face of the sand. Strictly speaking, the back-pressure varies over the face of the sand, owing

Jan 1, 1932

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By E. J. Dulis, V. K. Chandhok, J. P. Hirth

Cobalt clearly increased the activity of carbon in austenite and in ferrite. This effect of cobalt on carbon activity Plausibly accounted for the effect of cobalt on accelerating the austenite to pearlite transformation. Cobalt was found to have only a slight effect on carbon diffisivity in various Fe-Co and Fe-Co-W-Mo austenites, but was found to decrease carbon diffusivity in Fe-Co ferrite. THE effect of cobalt in steel is unique in that it is the only element that reduces hardenability by accelerating the austenite to pearlite reaction. The results of several excellent investigations aimed at explaining the role of cobalt have been published,1"7 but a complete understanding is still lacking. In addition, cobalt significantly enhances the resistance to softening or tempering of highly alloyed highspeed and hot-work tool steels. The resistance to tempering is related to the secondary hardening reactions associated with the fourth stage of tempering during which carbides of molybdenum, tungsten, and/or vanadium form in a martensite matrix. The effect of cobalt on secondary hardening reactions in high-alloy tool steel has received considerable attention, but a full explanation of the reactions involved has not been developed. Inasmuch as austenite to pearlite transformation and secondary hardening involve carbide formation, the present authors believed that the role of cobalt in effecting carbon activity and diffusivity in austenite and in ferrite was important to a fuller understanding of the phenomena involved. TO investigate the effect of cobalt on the activity coefficient of carbon in austenite, an approach was used similar to that used by Darken17 in his experiments on the effect of silicon, manganese, and molybdenum on carbon activity and diffusivity in austenite. TO

Jan 1, 1962

By H. C. van Elst

Ultrahigh-speedphotographic and electronic meth-ods were applied to an investigation of details of brittle-fracture propagation in steel. The brittle fractures studied were obtained in steel plate with the aid of a Robertson apparatus. It was found that a brittle fracture proceeds by discrete steps ranging from 30 mm near the stop temperature to less than 2 mm at lower temperatures. The halting FROM prior metallographic observations of brittle fracture in steel' it could be concluded that the distribution of mechanical twins along a brittle fracture was similar to the distribution of mechanical twins induced by explosive deformation. It was therefore assumed that a running brittle fracture created stress waves, cf. Refs. 2-7. An emission of stress waves by a brittle fracture, however, seems only conceivable if the fracture propagates by discrete steps. For this reason a study of the details of times between successive steps drop in this tem-perature region from 20 usec to about 1 psec. The stepwise propagation mechanism is accompanied by an intermittent emission of stress waves of the order of 100 to 200 kg per sq mm. These stress waves seen1 to play an important role in the mechanism of brittle fracture as will be discussed. brittle-fracture propagation was undertaken to investigate the possible determination of the fracture steps and the emitted stress waves associated with the assumed mechanism. The more practical object of this work is the development of a test method for the determination of the ductile-brittle transition in small specimens. This has special advantages for the study of irradiation damage in steel. In this test method, which will be published in a following paper, the stress waves emitted by an actual brittle fracture are reproduced with explosive or electrical means and are then transmitted through small specimens at various temperatures. In the present paper only the results of the brittle-fracture study will be reported.

Jan 1, 1964

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By G. Derge, M. Bourgon, G. M. Pound

A STUDY of electrical conductance in molten Cu-Fe sulfide mattes' has shown that pure molten Cu,S behaves like a semi-conductor in that it is an electronic conductor and its specific conductance, of the order of 100 ohm-' cm-', increases with increase in temperature. On the other hand, pure molten FeS, another electronic conductor, behaves like a metallic conductor in that its specific conductance, about 1500 ohm-' cm-', decreases with increase in temperature. Molten solutions of Cu,S and FeS follow a roughly additive rule of mixtures with respect to both specific conductance and temperature coefficient. The behavior of molten Cu,S may be understood, by analogy to the situation in solids, in terms of semiconductor theory.' It is thought that, although the melt consists of cuprous and sulfide ions, the bond between these atoms has a certain degree of cova-lency. According to the simplest concept the electrons in the partially covalent bonds are thermally promoted to a conduction band. In another concept, small amounts of impurities (undetermined) provide donor or acceptor levels in the forbidden zone between the valence and conduction bands and thus facilitate semi-conduction in the usual way. However, the metallic behavior of molten FeS is difficult to explain, because one might expect from similar reasoning that it too should act like a semi-conductor. It was suggested that the apparent metallic behavior of molten FeS might be explained by a large negative temperature coefficient of density. Thus if molar conductance instead of specific conductance were plotted versus temperature, the slope might prove to be positive, indicating semi-conduction instead of apparent metallic conduction. Accordingly, density measurements were made in order to answer this question in regard to molten FeS and also to provide data for conversion of specific conductance to molar conductance for molten Cu,S and a molten 50-50 wt pct Cu-Fe sulfide matte. Experimental Diagrams of the apparatus are given in Figs. 1 and 2. A 3 x 8-cm dense alundum crucible containing the prefused specimen is positioned in the uniform temperature zone of an induction furnace tube and melted under a helium atmosphere. Then the cell assembly, consisting of two 3-mm spectro-graphite rods, one of which is in a 1-cm ID open

Jan 1, 1959

By Reinhardt Thiessen

Under sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of balls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists in the coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otllerwise prepared for use. Pyrites in Microscopic Particles All coals that have been examined by the author contained a varying amount of sulfur in very small globules, or particles, of pyrite. These particles are seen in a thin [section as roughly rounded opaque dots, Figs. 1 to 10. When isolated, they are generally shown to be approximately spherical in shape, with a rough outer surface. They vary in diameter from a few microns to a hundred microns, the majority messuring from 25 to 40 microns; relatively few exceed the latter diameter. They are, therefore, very small objects. Their size is best appreciated by comparing the illustrations, in which they are shown. at a magnifiea tion of 100 diameters, with some known area like the period used in the ordinary printed page. The period is about 0.6 mm. in diameter, and . when magnified 100 times, will cover a circular area of about 2 1/2 in. in diameter, or all but the corners of the illustrations. The illustrations, therefore, represent an area about as large as an ordinary period, and the pyrite globules form but a small part of the total area. Very frequently a number of these particles are joined together in horizontal rows; oc-

Jan 1, 1920

By Joseph Pogue

THE prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry.

Jan 3, 1924

By E. A. Anderson

IN another paper1 the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 lb. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging.

Jan 1, 1929

By John Mathews

DURING the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table; stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also listed in the table, as said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed anew oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank-case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20° and 100° C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for 1° C.; cast aluminum (99.93 per cent. Al.),

Jan 2, 1920