Search Documents

By E. J. Schmitz

The existence of copper-ores in the Permian measures of Texas has long been known, and these ores have been, from time to time, the object of geological researches and mining

Jan 1, 1897

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young's modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young's modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-' (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young's modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C'. Young's modulus of polycrystalline samples with strong [110] textures and Young's modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young's modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young's modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

By Blair R. Benner, Ronald J. Roman

The rate of acid leaching of malachite from a sandstone ore was shown to be controlled by the diffusion of H+ ions through the host rock. The kinetics of the reaction can be expressed by a shrinking core model. Equations for calculating effective diffusivities from an "infinite" slab and a cylindrical core were derived. The effective diffusivity, of H+ ions in a sandstone ore was measured.

Jan 1, 1975

By Charles A. Ashburner

DURING the early part of August, 1880, I was directed by Prof. J. P. Lesley, State Geologist, to assume charge of the geology and mapping. of the Second Geological Survey of the anthracite codfields. I visited the region uninaumbered by any instructions other than this,—that I should submit a plan for making the sur-

Jan 1, 1881

By John P. Bernardi, Ralph B. Hall

Past and present phosphate production in the central Florida phosphate district has been predominantly from the unique Bone Valley formation. As these lucrative reserves are depleted, production will shift to the Hawthorn formation in all areas, but particularly so within the southern extension, where vast potential reserves of low grade phosphates exist. Use of existing plants can be extended for some years by mining deeper into the underlying Hawthorn formation, and by mining previously ignored peripheral areas if erratic combinations of the two formations. Hawthorn Production, as compared to the Bone valley, will be characterized by lower grade; lower tonnage yield, lower pebble percent of product, higher mining ratios, higher slimes (- 150 mesh) content, and more complex mining and beneficiation problems. Geological control and more sophisticated operational procedure; will become increasingly more important as the lower quality reserves replace Bone Valley production.

Jan 1, 1981

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By T. F. Witherbee

On .the 22d of November, 1879, white, iron unexpectedly ap peared while working the Cedar Point Furnace, Port Henry, N Y., on the following burden, calculated to turn out mill and foundry iron: Anthracite coal,. ., .. .. 8000 pounds. Connellsville coke,. ..1500 " Total,..4500 " Old Bed ore,........ 3750 " New Bed fine ore,. ..2000. " New Bed chunk ore,. .. 1000 " Kearnev hematite ore,.750 " Total,..... 7500 " Magnesian limestone,. 1665 " Common limestone,. ...835 " Total,........ 2500 " The production per week since making mill iron-—from September 1st, 1879, to date, seven weeks—was 412 gross tons. Ore was not immediately taken off, as nothing serious was looked for. The iron for the next week graded from No. 4 to white, and in six days the make was 2741/2 tons. At 10 p.m., Friday, the 28th, a slip of -14 feet occurred, and on Saturday, at 5 A.M., another of 3 feet on the south side and 7 feet on the north side took place. At this time it was found that the south side had been hanging for over a week—a fact which had not been reported. Throwing off the wind, to produce slips and reduce pressure, had been tried with no effect. The stock, as seen through the tuyeres, seemed to consist almost entirely of coal, with just enough infusible cinder to cement it into a mass through which the blast could not be forced. At 3.50 A.M., Sunday, the 30th, the first cinder seen in seventeen hours came into tuyeres Nos. 1, 2, 3, and 6. At 9.30 A.M. No. 3 was taken out to see if the stock

Jan 1, 1881

By Jack Fox

Three years ago we attended the V International Mining Congress in Moscow. This year we attended the VI International Mining Congress in Madrid. By almost any criterion, this was a most successful convention. There were 1717 registrants, not counting the ladies. I don't know how many of the latter there were, but they certainly made a welcome addition to the group. Once again, the International Organizing Committee put together a very impressive technical program which the Spanish National Committee backed up with a brand new Palacio de Congresos admirably equipped with simultaneous translation devices and an organization that provided an excellent social program, a tremendous set of post- meeting excursions, and very impressive opening ceremonies, entertainment and closing ceremonies. There was also an exhibit on the subject of Spanish and Spanish American mining history in the Palacio de Congresos.

Jan 1, 1970

By George W. Orton

i\- number of investigations have established that tungsten monocarbide (WC) forms throughout a wide range of temperatures (800° to 2200°C), but the di-tungsten carbide (W2C) forms only at the high end of this temperature range.1"7 In addition the decomposition of WC into WzC and C at elevated temperatures has been observed.8"10

Jan 1, 1964

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific North-west shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 2, 1950

By H. B. Emerick

An effort has been made to evaluate the individual influence of various factors in steel making and rolling operations upon the surface quality of semi-finished steel products. The thoughts expressed are not entirely theoretical, but rather are based upon several years critical observation of mill yields and rejec-tions and are supported by actual data wherever this has been possible.

Jan 1, 1940

By Mario L. Villa

During 1938, oil activities in the Argentine Republic showed a favorable balance due to the increase in crude-oil production, the incorpora- tion of new producing areas and the discovery of deeper productive horizons. Drilling was as follows:

Jan 1, 1939

By Mario L. Villa

During 1938, oil activities in the Argentine Republic showed a favorable balance due to the increase in crude-oil production, the incorpora- tion of new producing areas and the discovery of deeper productive horizons. Drilling was as follows:

Jan 1, 1939

HAVING shown you before how moulds of statues and also those of guns are constructed, I wish to tell you at present how, if you wish to cast them in bronze, you are further to prepare and arrange these moulds so that they may receive the melted mass of the metals in a friendly manner and without disturbance. I know that you understand that a real and intense heat has been intro-

Jan 1, 1942

By David Phillips, George Jura

WHEN Bridgman1 determined the volume-pressure relationships of bismuth to 100 kg Cm-2, he found two small volume discontinuities at 45 and 64 kg em-2. Probably every investigator in high pressures has determined the electrical resistivity of bismuth in this pressure range. Until Zeitlin and Brayman2 reported discontinuities in the resistance of bismuth at these pressures, no one had found resistance discontinuities

Jan 1, 1968

By Edgar C. Bain

Jan 1, 1932

By Robert H. Richards

Jan 1, 1883

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By R. M. Brick

A PREVIOUS publication 1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl2. A similar study has been made of the aluminum-rich aluminum-mag-nesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for pre-cipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys.

Jan 1, 1935