Search Documents

By Gherman Pavlovich Nikonov

Results of preliminary research on the use of small diameter water jets at high pressure for cutting rocks has demonstrated the possibility of effective cutting of anthracite. Detailed research has, therefore, been conducted at the Skotchinsky Institute of Mining to study the dynamics and structure of the small water jets and the mechanism by which they cut coal. One of the objects of this research was to obtain data for the design of a machine for cutting rock, based on the same principles as that for cutting coal. The productivity of water jet mining machines depends on the hydro- dynamic parameters of the jet. Therefore, the research on small diameter water jets was directed, initially to a study of the nature of the variation of these parameters, and to obtain a profile of dynamic pressure distribution over the section of the jet. As has been confirmed previously, the required jet pressure (to cut coal) lies in the range of 100 to 500 atmospheres. These pressures were utilized for the research. The diameter of the nozzle was changed as ~follows; 0.97; 1.24; 1.5; 2.17; 2.87; and 3.57 mm. Graphs showing dynamic pressures for each nozzle diameter and varied axial dynamic pressure were obtained over distances ranging from 2 to 70 cm from the nozzle. One of the most important hydrodynamic parameters of a jet, closely related to the dynamics of jet disturbance in air, is the magnitude of the axial dynhmic pressure. A study of the variation in this pressure with increasing distance from the nozzle led to the separation of the jet into three specific parts, which differ from each other not only in the nature of the change in dynamic pressure, but also in structural properties.

Jan 1, 1971

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By W. A. Clark

THE production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl, of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. REASONS FOR GRAVEL-PACKING Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b). allowing deep submergence of the pump into the oil zone.

Jan 1, 1939

By J. M. Hodge, H. M. Reichhold, R. D. Manning

The work reported in this paper represents the first of a series of investigations of the factors governing notch toughness in ferritic materials. This paper is concerned with two of these factors, namely, the effect of ferrite grain size, and the effect of an alloy content of 3.64 pct nickel. Every effort has been made to hold other variables constant in order to isolate the effects of these two. The compositions chosen for study were 0.02 pct carbon in order to eliminate the variable of carbide distribution, one steel being a plain carbon steel and the other alloyed with 3.64 pct nickel. Both steels were fully killed with silicon, without an aluminum addition, so that the variable of deoxidation practice was held constant. Finally, all samples were water quenched from 1200°F and tempered 24 hr at 300°F in order to hold the quench aging variable constant and to decrease the tendency for grain boundary carbide precipitation. The ferrite grain size was varied by heat treatment over the range of A.S.T.M. grain size numbers of about 2 to 6 in each steel so that the effect could be evaluated individually and the notch toughness of each steel could be compared at comparable ferrite grain sizes. Materials and Experimental Procedure MATERIALS The materials for this investigation were obtained from Battelle Memorial Institute as 250 Ib induction melts which were forged into 134 in. square bars and then rolled into 0.6 in. square bars. Both steels were deoxidized with silicon, the aluminum content being held to a minimum. Check analyses of these materials are shown in Table 1. HEAT TREATMENT FOR GRAIN SIZE The grain size was varied by varying both the cooling rate and the austeni- tizing temperatures. The heat treatments used and the corresponding grain size values are tabulated in Table 2. A semicontinuous network of grain boundary carbide was observed in the microstructure of both the plain carbon and nickel steels in the as rolled condition and an additional heat treatment was necessary to eliminate this variable. Therefore, all samples were water quenched from 1200°F and tempered 24 hr at 300°F as a final treatment before testing. This heat treatment served to eliminate to a great extent the grain boundary carbide network and to hold the quench aging effect constant. IMPACT TESTING Standard keyhole Charpy impact tests were machmed after heat treatment. A bath of acetone and dry ice was used for refrigeration of the samples down to temperatures of —94°F (—70°C) and a bath of either methyl-cyclohexane or isopentane, cooled by

Jan 1, 1950

Alfred Stansfield, Montreal, Canada:—In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated for " grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the &'Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated ; above the solidus (curve An on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but, the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 1, 1914

By T. B. Massalski, Horace Pops

The occurrence and the temperature dependence of the athermal martensitic transformation in bcc Cu-Zn ß-phase alloys have been studied by cold-state microscopy, differential thermal analysis, and electrical -resistivity measurements. CinenzatograpJzic studies have shown that in the majority of alloys the transformation occurs in two stages. A thermoelastic phase, having a 'needlelike" uppearance, forms initially at the MS temperature and grows relatively slowly, chiefly in the edge (lengthwise) direction. With further cooling, an additional martensitic phase forms in rapid bursts at a lower temperature, MB, Both martensitic phases appear to have the same cry stallographic habit hut their modes of formation and growth are different. For the composition range studied, between 38.55 and 41.49 wt pct Zn, the habit planes determined are close to the (2.17 ,12) plane of the matrix, in general agreement with the prediction of the phenomenological theory of martensite formation. Thermal cycling through the MB temperature produces permanent plastic deformation in the 0 matrix and gradutally eliminates the typical burst phenomena. Thermal cycling only through the MS temperature produces no noticeable deformation effects. THE bcc Cu-Zn ß-phase alloys tend to become unstable at low temperatures and undergo a martensitic transformation,'-3 but the details of the transformation have not been completely determined. Following earlier metal log raphic and X-ray work1 Tichener and ever' determined by means of electrical-resistivity measurements the temperature range of the martensite transformation during continuous cooling. The transformation temperature was found to decrease with increasing zinc content, becoming about -130°C for an alloy containing 40.04 wt pct Zn. Hull and Garwood3 made a metallo-graphic study of Cu-Zn 0 brasses at temperatures down to -160°C, and determined the habit plane of the transformation product for an alloy containing 38.88 wt pct Zn. No metallographic studies below liquid-nitrogen temperatures have been reported. The martensitic transformation in ß-brass alloys can also be induced by deformation.1,4 The MD temperature corresponding to the appearance of the strain-induced martensite is some 300°C higher than that observed without strain, and hence the transformation can be strain-induced in alloys containing a higher percentage of zinc. Massalski and Barrett4 found that alloys containing as much as 51.89 wt pct Zn could be transformed into a faulted hcp structure by cold working at liquid-helium temperature. Because the details of the MS temperature and morphology reported in the literature are somewhat incomplete, a further study has been made of some of the above features. A design of a cryogenic stage for optical metallography5 has permitted the examination of specimens at temperatures down to 4.2oK, and the use of a cinecamera has permitted a study of the morphology on cooling and heating. The particular aim of the present work was to examine the transformation temperatures, the habit planes, and the growth morphology over a wide composition range in the ß-phase field. The effect of thermal cycling upon the subsequent transformation was also examined.

Jan 1, 1964

By J. J. Gilman, T. A. Read

FOLLOWING the deformation 01 zinc monocrys-tals, sharply bent basal planes are observed near several types of inhomogeneities. Three of these in-homogeneities have characteristics which are quite regular so that they can be studied and analyzed. These are compressive kink bands, "deformation bands," and the inhomogeneities near end restraints. The present paper describes experiments in which "deformation bands" were artificially produced, and bend plane phenomena are discussed in terms of dislocation theory. Also, two new bend plane phenomena are described. The importance of bend plane phenomena in the deformation of crystals is not widely recognized. Many phenomena may be explained in a manner similar to the discussion in this paper. Jillson1 has pointed out that the "punching effect" in zinc is a bend plane phenomenon and is not caused by prismatic slip.' Bowles3 has suggested that they may be involved in diffusionless phase changes. Cahn4 has discussed the role of bend plane formation in the polygonization of zinc. Experimental Work Tensile Kink Bands: Because of the geometrical similarity between "deformation bands" and "kink bands" (compare Fig. 1 of this paper with Fig. 1 of the paper by Hess and Barrett"), the band shown in Fig. 1 of this paper will be called a "tensile kink band," and that shown by Hess and Barrett will be called a "compressive kink band." It is felt that the term "deformation band" should be reserved for banded structures in polycrystalline materials such as iron." Tensile kink bands seem to form spontaneously in aluminum crystals deformed by tensile loading.7-10 In zinc and cadmium crystals they do not form in good, carefully loaded specimens.'." However, tensile kink bands can be produced artificially in zinc crystals. The present authors did this by scratching one of the flat surfaces of triangular crystals transversely with a sharp needle. Natural tensile kink bands caused by inhomogeneities sometimes appeared in deformed crystals which were identical in appearance with the artificially produced ones. Zinc monocrystals were grown by the Bridgman method in graphite molds. Chemically pure zinc (99.999+ pct Zn) was used and the molds were sealed inside evacuated pyrex tubes during growth. The crystal cross sections were equilateral triangles with a typical base of 0.210 in. The artificial kink band shown in Fig. 1 is typical of tensile kink bands in zinc. The band lies between two bend planes which run from upper right to lower left and is inclined oppositely to the slip bands which are sharply bent at the two bend planes. The general form of the artificial tensile kink bands was independent of the scratch depth (1 to 5 mils deep) and also independent of which side was scratched. These variables did cause variations, however. Deep scratches produced more localized kink bands than light scratches. Also, if the angle between the slip plane traces and a transverse scratch varied appreciably among the three sides, then localization of the resulting kink bands also varied. Furthermore, if the slip direction lay nearly parallel to the scratched side, the band was more developed near the scratched side than at the opposite edge. Scratches produced tensile kink bands for crystal orientations from xo = 15" to x, = 75". Fig. 2 shows a scratched crystal after deformation. One triangular side lies in the plane of the photograph. The right hand tensile kink band was produced by a transverse scratch on the upper right side. The next two kink bands were the result of scratches on the front surface. The kink band at the left was caused by a scratch on the lower back side. All four bands have the same general form. A longitudinal scratch was also made on the crystal shown in Fig. 2 to determine the effect of a scratch on the critical shear stress. The critical shear stress of the scratched region was 33.9 g per sq mm compared to 24.4 g per sq mm for the un-scratched region above it. Fig. 3 shows Laue patterns of the crystal shown in Fig. 2. Fig. 3a shows the pattern of the undeformed crystal. The orientation was x, = 21°, A, = 31". After deformation, Fig. 3b was made of the homogeneously deformed portion of the crystal. The spots are compact but split into two halves. This region was elongated 45 pct and its orientation was x = 14", X = 20"; the sine law predicts x = 14", A = 20.5". Fig. 3c was taken near the center of the middle tensile kink band of Fig. 2. The pattern shows a range of orientations and polygonization in this region. The spread in orientation was due to the fact that the basal planes were curved (see Fig. 1) rather than flat as in the ideal case. Some may also have been the result of elastic distortions and "local curvatures." The orientation range was x = 23" to 32", A = 30" to 42". It is apparent from Fig. 3 that the material inside and outside the kink band rotated in opposite directions with respect to the tension axis during deformation. The orientation calculated from the ideal configuration of Fig. 9,

Jan 1, 1954

By James Hall

A geological map of a State involves very much, and its pre sentation to the public incurs grave responsibilities. It has been for a long time my earnest desire to bring out and place before the pub lic a geological map of New York which might be creditable to the State and worthy of a place among her scientific publications. We have done much for the advancement of geological science in this State—very much, and in many directions—but unfortunately, this feature, which should have been made the basis of all our work, has been too long neglected and delayed. For twenty-five years I have been laboring and looking forward to this consummation. I have recorded the field-work, systematic and desultory, upon such maps as were available for this use; and notwithstanding their imperfec tion, I have been able to transfer this recorded information to a more perfect base, which it is hoped will be completed during the early months of the next year. In 1883 I had combined, upon a small map of the State, the in formation which we possessed at that time, and communicated the same with my annual report to the Legislature. The report mas published in the regular course, but the special appropriation made for the map was vetoed by the Governor. Not discouraged by this untoward and unexpected circumstance, I continued my work, and made every effort to render the map more complete, preparatory to its communication with the next annual report. I brought together all the information within my reach, whether published or unpublished, reviewing and revising, as far as practicable, the work done by myself and assistants in southern and southeastern New York.

Jan 1, 1893

By Stanley M. Miller

The probabilistic nature of appropriate geologic variables can be included in analyzing the stability of potential slope failure modes. Random variables in the two-dimensional plane shear analysis of a specified structural discontinuity include the shear strength and waviness angle of the discontinuity and, in some cases, the rock mass density. Estimated probability density functions that describe these random variables are combined by Fourier analysis to produce an estimate of the safety factor probability density function, which appears to approximate a gamma distribution. The probability that sliding will occur along the specified structure is equal to the area under this density function where the safety factor is less than one.

Jan 1, 1982

By James Terry Duce

The gross production on the Island of Sahreirl during 1944 was approximately 6,700,000 U. S. bbl. No additional wells were drilled in the field during the year, but a number that were plugged off during the critical days of the war were brought back on production. This work is continuing. The construction of the extension of the refining plant was continued during the year and the new crude still was started in November. In Arabia, the production for the year 1940 was 5,074,838 U. S. bbl. Four wells were completed in Dammam field and all were commercial producers. Production for 1941 was 4,310,110 U. S. bbl. Seven more commercial producing wells were completed in Dammam field, and Well No. I at Abqaiq was complcted at 6180 ft. and was also a commercial producer. In 1942 production was 4,530,492 U. S. bbl. Abqaiq No. 2 was drilled to 5785 ft. but was left standing because of mechanical difficulty. The 1943 production was 4,868,- 184 with one well drilled, Abqaiq No. 3 completed at 6488 ft. and a commercial producer. Total production in Arabia for the year 1944 was around 7,800,000 U. S. bbl. and at the close of the year was running at approximately 40,000 bbl. per day. The small refinery, built in 1939, at Ras Tanura was in operation in the fall and a new refinery is being constructed. Only three wells were completed during the year—the El Jauf well in Northern Arabia (completed at 10,974 ft.) which did not bring in commercial production and Wells No. 4 (completed at 6270 ft.) and No. 5 at Abqaiq (completed at 6751 ft.), which were brought in as substantial commercial producers. Production for the year was entirely from the Dammam field. In this field, some of the wells that had been plugged off early in the war were brought back in production and this work is continuing. At the close of the year, one well was drilling in the Abqaiq field and an additional well was drilling at Qatif, the latter being a wildcat. Neither of the wells in question had reached producing horizons on the first of January.

Jan 1, 1945

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.' I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

By J. S. Ll. Leach, M. B. Bever

THE system copper-nickel exhibits complete solid and liquid miscibility1 The thermodynamic properties of such a system would not be expected to deviate greatly from ideality. Although the evidence is conflicting, anomalies in the composition dependence of various physical properties of solid copper-nickel alloys suggest that mixing may not be ideal.' From measurements of the Hall coefficient it has been concluded that clustering occurs in these alloys. ' Considerations involving the phase diagram of the ternary system copper-nickel-chromium have led Mei-jering3 to predict a positive heat of formation for solid copper-nickel alloys. An electrochemical investigation of the activity of nickel in copper-nickel alloys showed unexpectedly large positive deviations from ideality.4 wagner5 has proposed that if the entropy can be considered ideal, these measurements would yield the following equation for the heat of mixing at 700°C H" = 3380 x,vl (l-xVi) cal per g atom [I1 The heat of formation at 722°C of solid copper-nickel alloys of the equiatomic composition has been measured in a reaction calorimeter as 540 cal per g atom. This note reports calorimetric measurements of the heat effects on dissolution of some copper-nickel ndon: in tin. These measurements were preliminary to a larger investigation, which was later discontinued. From them the heats of formation of the alloys can be calculated, if certain assumptions are

Jan 1, 1960

By J. G. Richardson

The performance of laboratory water floods is compared with the flooding behavior calculated by the Buckley-Leverett techniques from steady-state relative permeability-saturation relations. Both the steady-state and unsteady-state experiments were conducted on the same sand-packed column. Relative permeabilities were calculated by the Welge technique from the unsteady-state waterflooding displacement experiments and compared with those measured by steady-state techniques. An evaluation of the various calculation procedures was made. It was demonstrated that steady-state relative permeabilities could be used to calczcJate waterflood performance. INTRODUCTION To calculate the waterflooding behavior of a given reservoir, relative permeability-saturation relations of the reservoir rock are required. These relative permeabilities are commonly measured on core samples by steady-state experiments such as the Penn State technique.' The relative permeabilities obtained in steady-state experiments are calculated from oil and gas flow rates and pressure drops measured under conditions of equilibrium distribution of oil and water in the pore spaces with slow approach to equilibrium. On the other hand, in water floods the water saturation at a given point changes rapidly with time as the flood front passes. Extensive research2 has shown that the steady-state relative permeabilities to oil and water are independent of the rate of flow and the fluid viscosities. Research has also demonstrated that the waterflooding performance of homogeneous sands uniformly contacted by water is independent of rate when capillary pressure gradients, which are important in short laboratory columns, are made negligible. However, there is little experimental data in the literature comparing relative permeabilities calculated from steady-state flow experiments with those calculated from flooding experiments. In this paper, the production data of two water floods and the relative permeabilities calculated from a series of steady-state experiments on an unconsolidated sand column are presented along with the comparisons calculated by the Buckley-Leverett and by the Welge techniques. The purpose of this study was to determine if steady-state relative permeabilities could be used to predict the waterflooding performance. This study also permitted an evaluation of the Buckley-Leverett and Welge calculation procedures and allowed an insight into the nature of microscopic displacement of oil by water. EXPERIMENTAL APPARATUS AND PROCEDURE The apparatus used in this investigation was a Lucite column 1 ft long and 11/2 in. in diameter. A drawing of the apparatus is shown in Fig. 1. Six pressure taps were evenly spaced along the top of the column to measure the oil pressures. Three pressure taps fitted with small porous disks were spaced along the side of the column to measure water pressure. Water was admitted to the inflow face of the sand through a porous disk while oil was admitted through a hole in the porous disk and distributed to the face of the sand by grooves machined in the porous disk. Retainer screens of 325-mesh stainless steel were cemented over the inlet and outlet ports and the pressure taps to prevent loss of sand. The column was packed with a clean dry sand all of which was finer than 200 mesh. Next, the sand was saturated with a solution of 150,000 ppm sodium chloride solution. The column was weighed dry and water-saturated to obtain data for the calculation of the pore volume. A 151-cp oil was then injected into

Jan 1, 1958

S. LE FEVRE, Forest Glen, N. Y. (communication to the Secretary*).¬F. L. Nason thinks I could not have studied Mr. Witherbee's paper and doubts the arithmetic used, but in his discussion arrives at practically the same conclusion. He says 10 ft. thickness of ore over a square mile should give 27,878,400 tons, allowing 10 cu. ft. per ton of ore. This is correct, but if he reads carefully he will see that this depth of ore was figured as covering one-tenth of the surface, which reduces the figures to those used by Mr. Nason. I did not say, however, that there were 2,300,000,000 tons of ore in New Jersey, but that applying the same method of computation as used by Mr. Nason, to the area of the iron ore-bearing gneisses in New Jersey, we would get a total of 2,300,000,000. I did say, "In this area are located 366 magnetite mines that have been worked more or less. These lenses may easily be capable of producing (on an average) 1,000,000 tons each, and there are probably double the number listed not opened up." Thus my estimate for New Jersey, as far as any was made, would be: Probable ore 366,000,000 Possible ore in addition 732,000,000 1,098,000,000 Mr. Nason's final conclusion of his personal estimate was one-half of what he erroneously read to be the estimate given in the paper, or half of 2,300,000,000, which equals 1,150,000,000. So the two estimates seem to differ less than 5 per cent., and we have the two sister States of New York and New Jersey on an equal footing of productive possibilities in magnetic ore.

Jan 6, 1917

By M. E. Learmont, R. J. Lipp, I. Iwasaki

In the selective flocculation of iron ores, the concentration of alkaline earth ions in pulp solutions plays a critical role. Sodium silicate, alone or with sodium tripolyphosphate, has been used as a dispersant. When Ca+ + concentration exceeds 15 to 20 ppm, however, only a strong complexing agent, such as ethylenediaminetetraacetate (EDTA) was found to be effective (Heerema, Lipp, and Iwasaki, 1979). Some iron ores release Ca+ + in excess of 20 ppm. With ores that contain gypsum, the Ca+ + concentration may reach several hundred ppm. The purpose of this investigation was to compare the effectiveness of EDTA with nitrilotriacetate (NTA) in countering the adverse effects of Ca+ +, particularly at high Ca+ + concentrations. Emphasis was placed on the use of NTA since it is more cost-effective than EDTA. It is also used in detergents in some countries (Malaiyandi, Williams, and O'Grady, 1979). NTA, like EDTA, forms a soluble complex with Ca+ + with a 1:1 molar ratio. Its structure and the value of log Kca are given below together with EDTA (Shibata, 1963). [ ] For experimental materials, an equal weight mixture of Lac Jeannine hematite and a high-purity quartzite from Thompson, MN, both ground to - 30 µm (- 560 mesh) was used. Selective flocculation test conditions and procedures were identical to those used in previous investigations (Heerema, Lipp, and Iwasaki, 1979). The optimum level of starch addition for the above mixture was determined to be at 300 g/t (0.6 lb per st). Initially, a series of selective flocculation tests were performed on the mixture pulped with 10-3M CaC12 (40 ppm Ca + +) at pH 11. With no NTA present, flocculation of the entire suspension resulted. The selectivities achieved in tests with 90, 100, and 150% of the stoichiometric amount of NTA were virtually identical to each other and also to the selectivity of separation obtained in the absence of Ca+ + Such an observation could have been expected since Ca+ + concentrations up to a few ppm may be tolerated in selective flocculation (Krishnan and Iwasaki, 1982). A similar series of tests were performed at 10-2M CaC12 (400 ppm Ca+ +). The results are shown in Fig. 1 as grade¬recovery curves. For comparison, the results obtained in the absence of Ca++ are included. At 90% of the stoichiometric amount of NTA, a large enough concentration of uncomplexed Ca+ + was left in solution to cause indiscriminate flocculation. Note in this figure that NTA is capable of countering the adverse effect of Ca+ + even at this high concentration when it is used in excess of stoichiometric amounts. The free Ca+ + concentrations at 100 and 150% are calculated to be 2.5 and 0 ppm, respectively. [ ] The relative effectiveness of NTA and EDTA was then compared at 100% of the stoichiometric amount using 10-2M and 10-3M CaCI2 (Fig. 2). EDTA appears to be slightly more effective than NTA. The free Ca++ of 0.02 ppm in 10-2M CaC12 with EDTA compared to 2.5 ppm free Ca+ + with NTA might account for the difference. As evident, prohibitively high additions of EDTA and NTA were required to complex high concentrations of calcium ion. The use of both of these agents would result in the accumulation of complexed Ca+ + in recycle water.

Jan 1, 1985

By R. J. Wysor

J. S. UNGER, Pittsburgh, Pa.-On page 22 reference is made to 36 carloads .of dust shipped. Did the material in that last sample come from a; furnace running on pig iron, ferro alloys, or spiegel? R. J. Wysor.-Pig iron; we have not made any ferro alloys; or spiegel at Bethlehem in the last 3 years. J. S. UNGER.-DO you use domestic or foreign ores? R. J. WYSOR.-In regular practice, largely foreign ores. J. S. UNGER.-How much per unit does it cost to produce that? R. J. WYSOR.-You might say it does not cost anything; we do not change our blast-furnace practice at all to obtain the dust. Although it has been a profitable byproduct, I would rather not have it unless we could reclaim it on a large scale, as we would have better working stoves. J. S. UNGER.-Does the trade take it as readily as natural salts? W. J. WYSOR.-The fertilizer dealers have been anxious to get it. This did not happen, however, until the war started. J. S., UNGER.-They have been willing to take anything since the war started. R. J. WYSOR.-Yes. However, we could have sold the material before the war; in fact, about 4 years ago, we had a contract ready to sign, but we did not think it would pay us to bother with it then. W. H. Ross, Washington, D. C.-We of the Fertilizer Division of the Bureau of Soils have been particularly interested in Mr. Wysor's investigations on the possibilities of recovering potash from the blast furnace, and we look upon the results he obtained as among the-most important that have yet appeared on the subject of finding new sources of .American potash. About 5 years ago we undertook a corresponding investigation on the recovery of potash in the cement industry. Representative samples of raw mix and ground clinker were collected from the different cement plants in this country with a view to analyzing each sample for potash. With the data thus obtained and knowing the ratio between the raw mix and the cement produced and the output of the latter, we thought it possible to calculate approximately for each plant the quantity of potash that escapes daily from the kilns. After partly completing the work, however, it had to be abandoned for a time. It was again taken

Jan 4, 1917

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of deslim-ing, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants. IN the past, mills treating ores of tin and tungsten by gravity concentration have recovered very little mineral finer than 325 mesh, although some form of slime concentration has been generally attempted by the use of buddies or round tables. This paper describes a series of pilot plant tests made in 1942 and 1943 in which the use of the Sullivan deck was investigated for the recovery of an appreciable amount of the fine values formerly lost. The investigation was initiated by the U. S. Government in an effort to increase the wartime production of tin. Bolivian milling practice at that time included jigging of the coarse sizes, tabling of the intermediate sizes on conventional shaking tables, and the use of buddies or round tables on the finest sizes. Flotation of the pyrite was employed at different stages of the treatment, depending upon the quantity present and the preference of the operator. Usually good recoveries and the bulk of the production were made in the jigging and tabling operations provided that these sections were not overloaded. Buddies and round tables were used for a small additional recovery if it could be shown that they could pay for their high cost of operation. Extensive test work established that by a combination of desliming, classification, and Sullivan deck treatment, cassiterite as fine as 10 microns (1500 mesh) could be recovered when proper conditions were maintained. This test work has been verified by several full-scale installations. The method is generally applicable to the preconcentra-tion of large tonnages of low-grade ores or tailings for the recovery of a small amount of a valuable heavy mineral. The Sullivan deck (or now the Denver Buckman tilting concentrator), which is the essential part of the method, was devised originally for the recovery of tin from tailings of the Sullivan concentrator, Kimberly, B. C. Since the material treated contained only 0.05 pct Sn, it was impractical to attempt to recover cassiterite finer than 500 mesh.*

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of deslim-ing, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants. IN the past, mills treating ores of tin and tungsten by gravity concentration have recovered very little mineral finer than 325 mesh, although some form of slime concentration has been generally attempted by the use of buddies or round tables. This paper describes a series of pilot plant tests made in 1942 and 1943 in which the use of the Sullivan deck was investigated for the recovery of an appreciable amount of the fine values formerly lost. The investigation was initiated by the U. S. Government in an effort to increase the wartime production of tin. Bolivian milling practice at that time included jigging of the coarse sizes, tabling of the intermediate sizes on conventional shaking tables, and the use of buddies or round tables on the finest sizes. Flotation of the pyrite was employed at different stages of the treatment, depending upon the quantity present and the preference of the operator. Usually good recoveries and the bulk of the production were made in the jigging and tabling operations provided that these sections were not overloaded. Buddies and round tables were used for a small additional recovery if it could be shown that they could pay for their high cost of operation. Extensive test work established that by a combination of desliming, classification, and Sullivan deck treatment, cassiterite as fine as 10 microns (1500 mesh) could be recovered when proper conditions were maintained. This test work has been verified by several full-scale installations. The method is generally applicable to the preconcentra-tion of large tonnages of low-grade ores or tailings for the recovery of a small amount of a valuable heavy mineral. The Sullivan deck (or now the Denver Buckman tilting concentrator), which is the essential part of the method, was devised originally for the recovery of tin from tailings of the Sullivan concentrator, Kimberly, B. C. Since the material treated contained only 0.05 pct Sn, it was impractical to attempt to recover cassiterite finer than 500 mesh.*

Jan 1, 1951