Search Documents

By David L. Holt, Walter A. Backofen, Anwar-ul Karirn

ANNEALING the binary alloy, Mg-0.5 wt pct Zr in a hydrogen atmosphere results in extensive precipitation of zirconium hydride. The morphology of these precipitates has already been investigated.lm3 Squires, Weiner, and phillips4 found, following creep testing of the hydrided alloy at 450" and 500°C, that hydride denuded zones formed along grain boundaries that were aligned approximately normal to the tensile axis. Zone formation was attributed to diffusional creep by magnesium transport down the prevailing stress gradients.4'5 Recently, electron microprobe analysis by Karim, Holt, and Backofen6 showed the zones indeed to be zirconium-free and furthermore it was shown that in compression, zones formed along boundaries approximately parallel to the stress axis. Thus it was confirmed that the zones are formed by diffusional creep. Typical zone-formation is shown in Fig. 1. Karim, Holt, and Backofen also measured the con- tribution to the total strain, from diffusional flow, slip creep, and grain boundary shear: results showed that diffusional strain tends to saturate with increasing imposed strain, while grain boundary shear eventually becomes the dominant deformation mode. It was suggested in explanation that the precipitate-denuded zones are soft and easily sheared, such deformation contributing to the grain boundary shear measurement. A point to be emphasized is that the Mg-0.5 Zr alloy was not superplastic for the index of strain rate sensitivity of flow stress, m = a log log 6 was only 0.25. It was recognized that diffusional creep in a poly crystalline aggregate must be accompanied by boundary shearing.' The suggestion was that the non Newtonian-viscous character of diffusional creep in the Mg-0.5 wt pct Zr alloy is due to resistance to sliding of boundaries lying approximately parallel to the tensile axis.= The work described in the present note should be seen against the above background for it represents initial efforts to observe in a similar way diffusional creep in a superplastic alloy. Previous work with the ternary-alloy Mg-6 Zn-0.5 Zr, pellet extruded, showed it to be superplastic however it does not contain resolvable precipitates to act as internal markers for diffusional creep. Also the fine grain size of the alloy (0.5 p) made conventional metallography rather difficult. Solubility relationships in the Mg-Zn-Zr system are not well known, however making reasonable guesses about the probable phase diagram of the ternary, Mg-Zn-Zr, various heat treatments were attempted to produce hydride precipitation. Finally a 16-hr anneal at 495' in hydrogen was found to pro-

Jan 1, 1970

By George S. Rice

A problem of possible subsidence of the surface from mining operations, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitching lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excavations. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1 to 12). The mining company had the right to remove the ore, the railroad assuming that the surface would be supported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence. Method oF Mining Before the problem became acute, the mining company, to decrease the possibility of subsidence, had been mining the part of the orebody that lay under the tracks by a room-and-pillar system, back-filling with

Jan 1, 1934

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By W. H. Emmons

Many mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and, many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement. Introduction When faults are followed along dip or strike, many of them are found to have curving or warped surfaces, and cross sections through them in most directions show sinuous or waving intersections. Openings are formed where one wall moves away from the other (Figs. I,2). Where there is a bend in the fault, movement in any directions except along the axis of the bend will

Jan 1, 1949

By Richard F. Miller, W. E. Milligan

Work was undertaken two years ago at the Hammond Laboratory for the purpose of determining the magnitude of the elastic range in single crystals of pure metals by means of creep tests, the assumption being made that if a true elastic range exists, the elastic limit represents the maximum stress for no creep. A sensitive extensometer was constructed, and creep tests were made on zinc single crystals at a variety of loads and temperatures1. It was soon discovered that there is no measurable elastic limit in ductile zinc single crystals at, or above, room temperature. The inference that pure metallic single crystals may not possess a definite elastic range was not justified, however, since zinc had been tested in creep only above its recrystallization temperature, and several investigator2,3,4 had already shown that above the recrystallization temperature polycrystalline metals will flow under very small stresses, while below that temperature stresses of a much larger magnitude are required. For that reason, it was decided to extend the study of the elastic limit to other metals having a higher recrystallization temperature than zinc. Aluminum and silver were selected, because of the ease of obtaining pure materials and of preparing large single crystals, and because the crystallo-graphic glide system of these metals is well known. Owing to the limited time available, the elastic range was investigated by slow tensile tests rather than by creep tests. Production of Specimens A luminum Recrystallized single crystals were prepared from 99.95 per cent aluminum supplied by the Aluminum Company of America. The ingots were melted in an Acheson graphite crucible in a gas furnace, and cast

Jan 1, 1937

By J. R. Johnson

ZIRCONIUM'S corrosion rate by reactor fuel solutions increases with increasing reactor power. It is believed that the protective oxide film is affected by radiation damage. Observations of the

Jan 1, 1959

By Arnulf Muan, Klaus Schwerdtfeger

Activity-composition relations in Pt-Cr and Pd-Cr alloys of low chromium concentrations UCr < 0.3) have been determined in order to ascertain quantitatively the extent of reactions to be expected between Cr2O3-containing oxide phases and platinum or palladium crucibles used as containers in studies of oxide equilibria at low oxygen pressures. This work is a continuation of similar work previously

Jan 1, 1965

By J. J. Scott, L. Adler3

L. Adler (Assoc. Professor, Department of Mining Engineering, Virginia Polytechnic Institute, Blacks-burg, Va.) - Dr. Scott is to be commended for undertaking the arduous and specialized task of applying three-dimensional photoelastic techniques to a mining problem. However, 1 feel his analysis suffers seriously from a lack of clarification on one important matter, among several others; and that the paper as a whole lacks balance and thus tends to confuse the reader. 1) The major technical criticism refers to the fact that nowhere are the boundary conditions for his mod-

Jan 1, 1964

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth&apos;s substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth&apos;s substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By A. K. Snelgrove

This symposium is designed to marshal a state-of-the-art account of approaches and solutions to problems arising out of waterlogging and salinization in the world&apos;s largest irrigation system which was dismembered by legal beheading of the Eastern Rivers under the lndus Waters Treaty of 1960. In this introduction, the geological and historical backgrounds of surface waters and groundwaters in the Indus Basin are presented with a summary of remedial measures undertaken and proposed to combat waterlogging and salinization. At a time when water-resource planning is proceeding on a continental scale, a study devoted solely to the Indus River Basin may seem to require an apologia. None is offered, however, for three major reasons: (1) Although the Indus is a single river basin, it is one of great magnitude and importance. The Indus River, which comes from Himalayan sources to form part of the great Indo-Gangetic Plain drainage system, is vital to agriculture and hydroelectric power in the thickly populated northern subcontinent of Indo-Pakistan. (2) The Indus has become a plexus of extraordinary problems since the dismemberment of the world&apos;s largest irrigation system of which it was a part. The break-up of this system occurred with the legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960. (3) Th River Basin has been the target of a Herculean effort to contain the twin encroachments of waterlogging and salinization that now threaten it with a shortage of fresh water. The British irrigation system of barrages and canal on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage. To cope with this situation, there has been a possibly unprecedented concentration of domestic and international engineering and scientific talent on the Indus and its problems (about a score of organizations by recent count). To marshal a state-of-the-art account of their approaches and solutions is the purpose of this Symposium. The coordinated effort now being made on a variety of fronts under the general supervision of West Pakistan Water and Power Authority (WAPDA) is directed toward the modification and control of interactions and relationships between geological materials — soils, water and its salt balance, and air —in what has been termed a huge "underground lake" in an alluvial basin. The problem is an intriguing one in that a highly complicated case history of river-course changes visible in the present surface must be projected downwards through Recent and Pleistocene sediments in order to decipher the environmental controls of deposition in terms of vertical and lateral variations in lithology and patterns. Such studies must be extended to compaction, deformation, and fabrics of the alluvium. Geohydrology is often defined as groundwater hydrology. As employed herein, it includes the distribution, quality, and behavior of surface and subsurface waters, including their evolution, vagaries, and geological, climatological, and botanical milieux." GEOGRAPHY The Indus (Sanskrit, Sindhu = river) rises at nearly 17,000 ft above the sea in the glaciers on the northern slopes of Kailas Parbat, Tibet. It is about 1800 miles long and has a total drainage area estimated at 372,000 sq miles. The average discharge is 196,000 cfs at mouth. Leaving the Plateau of Tibet, the river flows at a level which is miles above the sea, and in places miles below Himalayan peaks, in a structurally controlled northwestward course. Joined in this course by six tributaries and swollen by the melt waters of giant glaciers, it swirls about the base of the famous

Jan 1, 1970

By John Naughton

At the General Electric ResearchLabora-tories, we have been interested in the iron-manganese system and the effect of hydrogen on the properties of these alloys. Dr. H. H. Uhlig previously has presented some of these results.&apos; We wish now to offer some other of the data that have a bearing on the subject of this symposium. In the determination of hydrogen in the iron-manganese system by any heating Method we are presented with the problem of the evaporation of volatile manganese and the consequent adsorption of hydrogen by this evaporated metal. It seems wise. therefore, to extract gas at as low a temperature as feasible. Consequently we chose the vacuum or hot extraction method for the analyses of these alloys. The apparatus used is shown in Fig. I. The design is a modification of the apparatus described by Holm and Thompson. To limit loss of hydrogen, samples are stored in a chamber immersed in liquid air. We recommend this procedure whenever there is a question of loss of hydrogen at room temperature. Thence they are moved to the quartz furnace by means of a small magnet, where they are heated by induction to 700&apos; to 800°C. The extracted gas is removed by the circulating pump and placed in the known volume VI (or V2). The circulating pump has been described.3 It is so designed that in spite of the fact that the outlet portion of the pump is part of the known volume, this volume is affected neither by the speed of pumping nor by the pressure of stored gas. The pump also serves to circulate the gases for analysis. The analytical system consists of a

Jan 1, 1945

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By R. D. Pehlke, J. V. Gluck, R. L. Louvet

A study has been made of the effect of small additions of bismuth on the activity of zinc in dilute solution in molten tin. Free-energy interactions have previously been determined between zinc and various third elements where the solvents were molten bismuth or molten lead.&apos;-4 In both of these solvents, the activity of zinc exhibits a strong positive deviation from ideal behavior (at 550°C y° for zinc in lead is 11.4 and for zinc in bismuth is 3.0). The present work, using tin as the solvent, is an extension to a case where the positive deviation is considerably diminished (y°Zn at 550°C is 1.63). Several previous investigators have studied the Zn-Sn binary system; however, little data is available in the range below 0.1 mole fraction zinc.5= Previous high-temperature galvanic cell studies in the Sn-Zn-Bi ternary system included the determination by Gluck and Pehlke of interactions in the bismuth-rich corner1 and separate investigations of the central region by Oleari and Fioriani6 and by Ptak and Moser.7 Yokokowa et al.8 conducted Knudsen effusion studies in the central region; however, their experiments at 625°K were conducted somewhat below the present experimental temperature range. Their results indicated an increase in zinc activity with the addition of bismuth. The present series of experiments was conducted in galvanic cells represented as follows: Zn Zn++ in LiCI-KC1 eutectic Zn + Bi in Sn (pure reference (fused salt electrolyte) (molten alloy) standard) The experimental apparatus. a multi-electrode system employing alumina crucibles and contained in a Vycor tube under a helium atmosphere, has been described previously, as have been the experimental procedures, precautions, and the methods of data reduction.1-4,- The experimental measurements were made over the range from 450° to 650°C. Between thirty and forty measurements were made in each run. The linearity of the electromotive force vs temperature relations was verified by linear regression techniques. The correlation coefficients exceeded 0.99. The experimental results summarized in Table I include the interpolated electromotive force at 550°C and the temperature dependence of electromotive force. Only results from stable and consistent cells containing more than 0.025 mole fraction zinc are reported. Attempts to run cells at 0.01 or 0.02 mole fraction zinc were not satisfactory. This is attributed to the closeness of the free energies of formation of the chlorides of tin and zinc. Calculations employing Wagner and Werner&apos;s criteria for displacement reactions10 indicated that reduction of the zinc content to 0.01 mole fraction places the cell near the borderline concentration for a 1 pct error in measured potential. The compositions shown in Table I are the actual weighed-in amounts. Previous experience has indicated that compositional changes during the running of a stable cell are negligible.&apos; Over the range of compositions studied for the binary alloys, the activity coefficient of zinc was essentially constant indicating that Henry&apos;s law is followed to 0.05 mole fraction zinc. The temperature, OK, de-

Jan 1, 1969

By B. S. Lement

No appreciable stabilization of the austenite-martensite reaction occurs in a 15 pct Cr-0.7 pct C steel unless some martensite is initially present. Stabilization is induced by interrupting the subcool below M,; however, disappearance of the stabilization effect as manifest by burst formation of martensite may occur on continued holding at the final subzero reaction temperature. The higher the temperature of intermediate cycling after the initial subcool, the more permanent is the stabilization effect at the final reaction temperature. Appreciable conditioning of retained austenite occurs on reheating to about 500°C. These phenomena are explainable on the basis of the reaction-path theory. A RECENT investigation&apos; carried out by the authors has shown that isothermal transformation of austenite to martensite definitely takes place in a 15 pct Cr-0.7 pct C steel and that appreciable amounts of martensite can form in this fashion. Investigations2-" arried out on other steels and iron alloys make it seem probable that isothermal formation of martensite is a phenomenon of fairly general occurrence. The reaction-path theory of Cohen, Machlin, and Paranjpe5,7 explains isothermal transformation on the basis of thermal activation of strain embryos which generate martensite plates with a velocity approaching that of sound. On the other hand, the nucleation and growth theory of Fisher, Hollo-mon, and Turnbull8 egards isothermal transformation as due to growth of athermally formed martensite nuclei. The experimental evidence obtained thus far favors the reaction-path theory in that the martensite reaction seems to be nu-cleation-controlled rather than growth-controlled. Stabilization is another phenomenon of importance with respect to the austenite-martensite reaction. According to the reaction-path theory, stabilization is a result of relaxation of strain embryos. It is postulated that strain embryos are present at the austenitizing temperature in the form of dislocations or lattice imperfections in the austenite which vary in the extent to which the lattice is displaced along the strain reaction path leading to martensite. On quenching from the austenitizing temperature, athermal martensite starts to form as soon as the M. is reached, because the activation energy of the transformation which decreases with decreasing temperature is lowered to below the level of the highest energy strain embryos. Martensite plates are generated during the cooling below M, from embryos possessing energies above the activation energy corresponding to the temperature at which the cooling is stopped. The distribution of lower energy embryos is changed because of the elastic and plastic strains produced in the remaining austenite as a result of the transformation. This effectively increases the number of strain embryos at all levels of energy below the activation energy and tends to stimulate further martensite formation either iso-thermally or on subsequent cooling. However, if the temperature at which the cooling is stopped is high enough for relaxation of strain embryos to occur, some degree of stabilization against further transformation may be induced. Whether stabilization will be observed on subsequent cooling will depend on the extent of decrease of activation energy with temperature. If the activation energy decreases sharply with temperature, it is possible that transformation will appear to continue with decrease in temperature in spite of the loss of embryos by relaxation. However, with a more gradual decrease in activation energy, stabilization will be manifest by no further transformation on cooling over a measurable temperature range until the

Jan 1, 1954

By D. W. Smith

The beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.&apos; R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 6 phase in the system copper-zinc takes the form of needles lying parallel to a [Ill] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [ill] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective ß phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum. Segregation of the a Phase from the ß Phase in the Copper-tin System Preparation of the Alloy.—An alloy containing 74.92 per cent (by weight) of copper and the balance tin was chosen for this investigation. This alloy, as can be seen from a portion of the constitutional diagram, Fig. 1, of the system copper-tin by Hamasumi and Nishigori,3 with the proper heat treatment should segregate the « phase out of the a parent, solid solution phase. The alloy was prepared from high purity cathode copper (analyzing 99.98 per cent Cu) and Straits tin (analyzing 99.94

Jan 1, 1933

By A. E. Bellis, T. W. Hardy

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operatioqs. Hundreds of dollars are spent in the design and manufacture of milling cutters of special form for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring-the tool out "clean," is a difficult one and calls for no small amount of skill. In order to be on the safe side the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed stee1, in which metallographic means were used to determine the correct hardening tempcratures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accom- . panying table. Six specimens from the same bar of each kind of steel

Jan 1, 1917

By T. L. McCall

This is a continuation of the paper on bumps presented by the late Mr. Herd in February, 1929. The seam worked consists of bituminous coal, 9 ft. thick, pitching 20°, and now under a depth of cover of 2800 to 3200 ft. Full particulars are given of two bumps that happened in November, 1931, with an interval of only 9 hr. between them. The first was a "district" bump affecting an area of 1000 ft. on the strike by 700 ft. on the dip and rise, beginning at a distance of 1000 ft. from the long-wall faces. The second, which caused much greater damage, was localized to two levels 200 ft. apart, in the area left undisturbed by the first bump next to the longwall faces. Observation stations had been established in the workings in 1931 and definite records were obtained on the flow of coal taking place from the edge of large pillars developed for retreating work, into the open roadways. The records also gave evidence that "advance weighting" or "underdraw " was affecting the coal at an average distance of 260 ft. in advance of the longwall faces. The author propounds the theory that the sandstone bed varying from 0 to 75 ft. in thickness and lying 14 ft. above the coal acts as a slab in distributing the superincumbent weight. The weight is thereby concentrated on the pillars in advance of the longwall faces and this load, in conjunction with a pavement strong enough to resist the reaction, leads to overstressing the pillars, which finally collapse suddenly, thus giving rise to this particular type of low side bump. The overlying sandstone bed, which is apparently a condition common to all coal mines in which bumps occur, is not necessarily a massive bed, as the thickness of this bed at Springhill in the area that has experienced these severe low side bumps is only 25 to 31 feet. A list of 43 minor bumps occurring in the past 2½ years is appended

Jan 1, 1934