Search Documents

By L. A. Shipman

The combustion of coal in fuel beds has been practiced as an art for many years; during the last 2 7 years a scientific approach to this subject has contributed a small amount of fundamental data. The subject is a very controversial one. Opinions regarding the performance of the same coal used in the same equipment in different plants may vary from "the best coal ever used in the plant" to "the worst coal ever tired." These opinions can all be true, owing to the various conditions under which the coal was used. Because of these differences, an attempt will be made in this paper to discuss coal facts and coal characteristics as related to the use phenomena observed during the art of firing coal in fuel beds for many years. The work of Kreisinger1 and his associates in the 1,'. S. Bureau of Mines, reported in 1916, was the first scientific attempt I know of to obtain factual data explaining the mechanism of combustion of fuel beds. They gave a chart showing an ignited fuel bed. The air passing up through the fuel bed first combined with the fuel by a reaction resulting in the complete combustion of carbon to CO2, which combined with the carbon in higher levels of the fuel bed to form CO with the absorption of heat. The fundamental facts produced in those experiments proved of much value and checked with practical experiences with hand-fired fuel beds. Hand firing was the prevailing method of stoking coal at that time. The order in which these reactions occur, as shown by Kreisinger and his associates, has been amply confirmed by repetition of this work with different fuels both her? and abroad. These experiments also showed that under their conditions the rate of burning was proportional to the air flow. These data were of practical value to a fireman and were accepted as generally true in all fuel beds. In later years many observations by myself in fuel beds of underfeed stokers and other thick fuel beds such as gas producers, where channeling. increase of particle size, or both, occur. indicated that, instead of the horizontal layers we had thought were present, perhaps the layers were vertical or irregular. Later investigations in fuel beds made by Mayers2 and Barnes3 indicated that the burning takes place in some instances along the surfaces of vertical or irregular channels or cracks in the fuel bed and that under these conditions a reaction occurs that differs from that in the old horizontal-layered handfired fuel beds. Examining the data in Kreisinger'sl experiments, and the information in different charts with different fuels, different retort positions and air admissions of Barnes3 and the gas analysis arid isotherms of Mayers,2 one can check experience observation and come to a conclusion that as particle size of the fuel increases with other conditions the same, the maximum CO2 and temperature

Jan 1, 1947

By L. A. Shipman

The combustion of coal in fuel beds has been practiced as an art for many years; during the last 2 7 years a scientific approach to this subject has contributed a small amount of fundamental data. The subject is a very controversial one. Opinions regarding the performance of the same coal used in the same equipment in different plants may vary from "the best coal ever used in the plant" to "the worst coal ever tired." These opinions can all be true, owing to the various conditions under which the coal was used. Because of these differences, an attempt will be made in this paper to discuss coal facts and coal characteristics as related to the use phenomena observed during the art of firing coal in fuel beds for many years. The work of Kreisinger1 and his associates in the 1,'. S. Bureau of Mines, reported in 1916, was the first scientific attempt I know of to obtain factual data explaining the mechanism of combustion of fuel beds. They gave a chart showing an ignited fuel bed. The air passing up through the fuel bed first combined with the fuel by a reaction resulting in the complete combustion of carbon to CO2, which combined with the carbon in higher levels of the fuel bed to form CO with the absorption of heat. The fundamental facts produced in those experiments proved of much value and checked with practical experiences with hand-fired fuel beds. Hand firing was the prevailing method of stoking coal at that time. The order in which these reactions occur, as shown by Kreisinger and his associates, has been amply confirmed by repetition of this work with different fuels both her? and abroad. These experiments also showed that under their conditions the rate of burning was proportional to the air flow. These data were of practical value to a fireman and were accepted as generally true in all fuel beds. In later years many observations by myself in fuel beds of underfeed stokers and other thick fuel beds such as gas producers, where channeling. increase of particle size, or both, occur. indicated that, instead of the horizontal layers we had thought were present, perhaps the layers were vertical or irregular. Later investigations in fuel beds made by Mayers2 and Barnes3 indicated that the burning takes place in some instances along the surfaces of vertical or irregular channels or cracks in the fuel bed and that under these conditions a reaction occurs that differs from that in the old horizontal-layered handfired fuel beds. Examining the data in Kreisinger'sl experiments, and the information in different charts with different fuels, different retort positions and air admissions of Barnes3 and the gas analysis arid isotherms of Mayers,2 one can check experience observation and come to a conclusion that as particle size of the fuel increases with other conditions the same, the maximum CO2 and temperature

Jan 1, 1947

By A. F. Lucas

The discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has gran with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting; and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable depth along lines of structural weakness; and that a deep well, properly located, stands an excellent chance of discovering the parent reservoir and thus of developing new and probably great supplies. This paper is presented as a discussion—necessarily hypothetical and based largely on personal opinion—of the possibility of encountering deep-seated oil deposits beneath the salt domes. Salt-dome Structure All of the oil produced in the coastal region of Texas and Louisiana is probably associated with salt domes, though in Goose Creek, Edgerly, and one or two other fields no salt has yet been actually penetrated. As

Jan 1, 1920

By William R. Patterson

ACCORDING to the phase diagram for the Mn-Ni system,' the high-temperature, fcc y-manganese solid solution is stabilized to below room temperature, in the range approximately 22 to 28 wt pct Ni. However, pearson2 cites evidence in the literature showing that for manganese contents greater than about 75 wt pct the quenched phase in Mn-Ni alloys is fct. This is in keeping with zener's3 suggestion that in manganese-rich alloys the fcc high-temperature phase undergoes a diffusionless or martensitic transformation to a fct structure upon quenching. Work by Basinski and christian4 on manganese-rich compositions in the similar alloy system Mn-Cu established that in alloys of greater than about 82 wt pct Mn the y-manganese phase underwent a fee fct martensitic transformation upon quenching to room temperature. Striking evidence for this martensitic transformation was the highly twinned or banded microstructure, an example of which is shown in Fig. 1. Similar microstructures have also been found in quenched Mn-Cr5 and Mn-Au6 alloys. In the present investigation, we attempted to obtain similar evidence of a fcc — fct martensitic transformation in manganese-rich Mn-Ni alloys. Manganese alloys in the range 10 to 30 wt pct Ni were prepared by arc-melting, under argon, at atmospheric pressure. The alloys all were 50 g in size, and negligible weight loss occurred during melting. The starting materials were electrolytic manganese and nickel, both of 99.9+ pct purity. The alloys were subsequently homogenized 48 hr at 1750°F, hot-rolled 50 pct at 1700°F, annealed 2 hr at 1700°F, and water-quenched to room temperature. All heat treatment was done in purified argon. Both X-ray and metallographic techniques were used to examine the structures of the quenched alloys. X-ray diffractometer studies were conducted on powder specimens obtained from filings rean-nealed 2 hr at 1700°F in argon and water-quenched. Identification of the intensity peaks from the diffractometer counter traces showed that below about 10 to 12 pct Ni the y phase decomposed partially upon quenching to give an a- + ?-manganese structure. In the range approximately 12 to 25 pct Ni, the structure was found to be fct ? manganese with a c/a ratio approaching 1.0 at 25 pct Ni. Beyond approximately 25 pct Ni, the structure remained fcc. These results, including lattice-parameter determinations, are given in Table I. Metallographic examination. was carried out on specimens polished and etched after quenching, and also on polished specimens reannealed and quenched. In the first case, the distinctive twinning or banding so prevalent in Mn-Cu alloys was sought, while in the second, the surface relief effect generally regarded as being truly characteristic of a martensitic transformation was sought. The microstructure of representative alloys in the range 12 to 25 pct Ni is shown in Fig. 2. The structure of the Mn-15 pct Ni

Jan 1, 1965

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson's3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

By E. T. Peters, L. E. Tanner

In the course of a study concerned with the rnechanical behavior of the intermetallic compound CO3V, both structural observations and anomalous electrical-resistivity behavior indicated the presence of a new high-temperature phase in an alloy with the stoichiometric composition, Co-22.4 wt pet V. The evidence, which is given below, suggests that the new phase is situated between the low-temperature ordered hexagonal phase, k,1, 2and the high-temperature disordered fee solid solution, a,3 within a small range of temperature in the vicinity of 1070°C. Structural studies included X-ray diffraction analysis* and electron-transmission microscopy examination* of stoichiometric composition speci- mens homogenized for 1 hr at 1200oC and either air-cooled or water-quenched. The air-cooled specimens yielded X-ray diffraction evidence of the k phase, while electron microscopy revealed a microstructure of both heavily and moderately faulted regions as shown in Fig. 1. The high density of stacking faults (or fine twins) in region A is reminiscent of hexagonal cobalt following its allotropic transformation.4 Selected-area diffraction from this region revealed distinct superlattice reflections of the ordered hexagonal phase, as well as continuous rel-streaks which were normal to the fault planes in the micrograph. The latter is indicative of extremely small spacings between the faults.' Regions such as ß were found to be only partially transformed to the k phase. Attempts to study the antiphase domain structure by either bright- or dark-field techniques were unsuccessful in these initial studies. This was due to the low intensity of the superlattice reflections arising from the closeness of the cobalt and vanadium scattering factors. Quenching Co3V from above Tc appears to suppress the formation of the k phase. Both X-ray and electron-diffraction results indicated that the disordered phase, a, was partially ordered during severe cooling and that the structure of the ordered phase was of the L12 (Cu3Au) type,6 designated here as a'. As in the case of the hexagonal phase, examination of the domain structure was unsuccessful; however, significant information concerning the morphology of this condition was revealed by the appearance of dislocation arrays. In particular, it

Jan 1, 1965

By C. D. Michaelson

Bridging the gap between have and have-not nations is one of the necessities of the present era. The responsibility for accomplishing this must be assumed by the affluent industrial societies of the world, both through their governments and through private enterprise. Despite a discouraging number of instances where companies established in underdeveloped countries have been expropriated, U.S. industry must not abandon such ventures. Instead, it should tailor them to the needs and aspirations of the host nations. One way in which industry can minimize the danger of expropnation is to enter into partnership with the government of the host nation. Kennecott Copper has recently done this in Chile, becoming 49% owner of a company formed to expand and operate the El Teniente mine. So far, the partnership has produced marked benefits not only for Chile, but also for Kennecott. The memory of D.C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was irnrneasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War 11, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling's remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential. CORPORATIONS ABROAD - AN EXPANDING ROLE Today the situation is quite different. The United States is now a capital-surpIus nation and looks abroad for opportunities to employ its capital profitably. On the other hand, we have become dependent on foreign sources for supplies of vital raw materials, while we seek

Jan 1, 1970

By J. S. Crump, H. L. Stone

Laboratory studies have indicated that displacement of oil from a reservoir by means of a condensing gas drive results in extremely high oil recovery, approaching 100 per cent under the most favorable circumstances. A condensing gas drive is defined as a gas drive in which the gas utilized is appreciably soluble in the oil it is displacing. The laboratory studies consisted of a number of gas drive displacement experiments, all using a horizontal, sand-packed, steel tube as the laboratory reservoir. The experimental results indicate that the more soluble a gas is in the oil to he displaced, the more efficient that gar is as a displacing fluid. Experiments were conducted utilizing both a light, volatile crude and a heavy, asphalt crude as the in-place oil. In both cases, oil recovery was appreciably enhanced by solubility of the displacing gas. It is believed that the use of condensing gas drives would result in increased oil recovery from many reservoirs during either primary or secondary phases of production. INTRODUCTION Since the early days of the oil industry there has been an increasing awareness of the problems of oil recovery. During the last few decades particularly a growing recognition of the problems has led to widespread attempts on the part of the industry to increase oil recovery by improved technology. One method which has been used to increase recovery is the maintenance of reservoir pressure by injection of gas. Part of the beneficial effect resulting from this gas injection was to prevent evolution of the gas dissolved in the reservoir oil, since such evolution would cause the oil to shrink and become more viscous, thereby adversely affecting oil recovery. In most instances, the gas injected was predomillantly methane, and so the possibility of oil recovery by retrograde vaporization existed. Laboratory investigations of displacement of reservoir oils by methane, carried out at high pressure, have indicated that considerable additional recovery of light oils could be effected by vaporization, but only at the cost of a severe volumetric shrinkage of the residual oil which would cause a decrease in relative permeability to oil in the reservoir. Consequently, recovery of oil by physical displacement would be impaired. The study suggested, therefore, that recovery of oil might be enhanced by injecting into the reservoir a gas known to be appreciably soluble in the oil at reservoir conditions. Swelling of the oil due to solution of gas should result and yield a consequent increase in the relative permeability to oil. The work described in the following sections was, therefore, undertaken to investigate the possibility of increased recovery by this mechanism. Research similar to that reported in this paper has been conducted by The Atlantic Refining Co.1,2,3 In these studies, Whorton, et al, and Slobod, et al, used methane-rich gas to displace oil from model reservoirs. Solubility of the gas was achieved by keeping the reservoir pressure greater than the saturation pressure of the original oil, and the degree of this solubility was varied by operating at different reservoir pressures. Thus the Atlantic project was primarily a study of the effect of reservoir pressure upon oil recovery by gas drive. The objective of the work reported in this paper was to study the effect of gas composition upon oil recovery while holding the reservoir pressure constant. DESCRIPTION OF EXPERIMENTS The discussion of the preceding section suggests that

Jan 1, 1957

By R. M. Treco

The effect of small additions of oxygen on the hardness, density, and lattice parameters of high purity zirconium has been investigated. Precision parameter values and density of oxygen-free zirconium are given as: a,, - 3.2258 kX units, C = 5.1373 kX units, O23 = 6.507 g per cc. THE effect of oxygen on the hexagonal-phase lattice constants of pure zirconium is of interest for several reasons. The extensive hardening effect of oxygen noted by previous investigators' must be due in part to the lattice distortion accompanying its introduction and possibly to the preferred position of the oxygen atoms. De Boer and Fast' have shown that oxygen is taken into solid solution in large amounts, appearing to occupy an interstitial position. These authors also found that expansion of the lattice was not uniform since the a axis attained a constant value after the addition of 10 atomic pct while the c axis continued to expand. It was thought in the present work that this expansion of the zirconium lattice with increasing amounts of oxygen

Jan 1, 1954

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By M. H. De Hora

(Butte Meeting, August, 1913.) IN giving my opinion of the importance of Colombia as a field for investment for those interested' in mining for the precious metals, I must begin by quoting Sir Clement Markham, who, in one of his presidential addresses to the Royal Geographical Society of Great Britain, called the attention of its members to the fact that " although Colombia is the least known and least developed of the South American republics, it is far and away the richest mineral country of them all." This to American investors is extremely interesting, as the country is the most accessible of all the South American republics from the United States. .Almost all of the gold shipped by the Spaniards from Madre de Dios, now Colon, came from Colombia, and statistics from the Mint at Medellin, the capital of the Department of Antioquia, go to show that the . total production of the precious metals of Colombia, dating from the Spanish conquest in the fifteenth century to the present time, aggregates the enormous total of $700,000,000. Of this amount, nearly 70 per cent. represents gold obtained from the placers of the Republic, more than one-half of which came from the Department of Antioquia, the balance, being divided between the placers of the Choco and the rest of the Republic. The remaining 30 per cent. of the $700,000,000 represents the silver and gold obtained from the quartz mines, the silver greatly predominating. A glance at the map of Colombia shows the territory somewhat in the shape of an outspread human left hand extended palm downwards on the paper, with the wrist adjoining the Republic of Ecuador, the bones of the hand, fingers, and thumb representing the divisions of the great Andean mountain chain known as the Cordilleras of Colombia. The first finger represents the Eastern Cordillera, with the thumb as the extension to the Nevada de Santa Maria, forming

Jan 7, 1913

By Steven T. Mitchell

INTRODUCTION Mill production from the Homestake Mine in 1979 amounted to 1.29 Mt (1.43 million st) of ore containing 5.9 g/t of gold (0.172 oz per st) compared with 1978 production of 1.44 Mt (1.59 million st) containing 6.2 g/t of gold (0.180 oz per st). The average cost per ounce of gold produced in 1979 rose to approximately $250 contrasted with $176 in 1978. This increase in unit cost is the result of inflation, a diminishing ore grade, and productivity losses related to a shortage of experienced miners as well as compliance with federal regulatory requirements. Together, these factors prompted the investigation of several large-scale, highly mechanized underground mining methods. This analysis indicated Vertical Crater Retreat mining to be one of the safest underground methods known today, yet competitive with all other forms of stoping in terms of cost and productivity. Therefore, the feasibility of applying the VCR stoping method at the Homestake Mine was explored. Vertical Crater Retreat stoping is a recent innovation in large- scale underground mining based on C. W. Livingston's crater blasting theories. Figure 1 illustrates the method which consists of drilling 165.1-mm-diameter (6.5-in.) holes from a topsill down-dip to an under- cut on the level below. The bottom of each hole is then loaded from above with a predetermined charge weight and horizontal slices up to 4.27 m (14 ft) in thickness are blasted into the undercut. Broken ore is extracted from drawpoints located on or below the undercut level.

Jan 1, 1983

By A. L. Field, P. H. Royster

Bureau of Mines Technical Paper 189 consists of a record of the scientific data obtained in the iron blast-furnace slag investigation which is reported in Technical Paper 187, "Slag Viscosity Tables for Blastfurnace Work." It includes a description of the method of preparing the synthetic melts, construction of an improved electric furnace, and refinements in laboratory methods of measurement. Only the general features of the work and the conclusions drawn from the experimental data can be given attention here. Silicates in the Liquid State In the manufacture of refractories, Portland cement, glass, and porcelain, and in pyrometallurgical operations, importance attaches to the behavior of-silicate compounds at temperatures beyond the range of common experience. This field of research has not been investigated as carefully as its scientific and industrial importance would seem to warrant. Probably the most important of the unsolved problems in the chernistry of silicates is the question of their stability in the liquid state. That little progress toward the solution of this problem has been made is not strange if there be borne in mind the difficulties attending experiments made at temperatures at which silicates become fluid, and the comparatively short time since it became possible to measure these temperatures. On the other 'hand, considerable progress has been made in the study of the compounds in the solid state because of the directness and simplicity of methods of optical examination. Important advances have been made by the Geophysical Laboratory at Washington in recent years. An extended study has been made there of saturated solutions representing a considerable number of binary and ternary systems of the more common refractory oxides. The methods

Jan 1, 1918

By John E. Caffrey

The Federal Coal Mine Health and Safety Act of 1969, Title III, Interim Mandatory Safety Standards for Underground Coal Mines, is devoted to protection of workmen from hazards of electricity, roof, ribs, fire, and explosions. The Rules and Regulations, promulgated through the Federal Register, provide the criteria by which the law would be administered. Certain aspects of the law involve features that could be summarized under entrapment. These are sections 303 (y)(1), (y)(2) and 317 (f) (4). This paper is intended through the use of the figures to describe how these features of the law affect mine ventilation design, what are the problems, and possible solutions to them.

Jan 1, 1974

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

By Will Coghill

As the title indicates, this paper treats of the degree of liberation of minerals after grinding. To obtain the supporting data a "tool" not commonly used by metallurgists has been employed. It is the "heavy solution." The advantages gained through its use are shown. Actual ores were employed in order to make the study concrete. The selection was somewhat incidental and happened to embrace the red iron ores of Alabama. So, any reader interested in these ores will find some of their properties described. The red ores constituted the material examined and a somewhat new adaptation of heavy solutions was the tool of examination. If either the ores or the tool interest the reader these notes may be of some value. The writer's chief interest was in the rate of liberation of locked grains. Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned. But when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imaginable conditions. Concentrating machinery has not taken a part in this investigation; the use of it would have been only machinery testing, and should never precede the ore testing which consists of such methods as herein outlined. When the properties of the ores have been gleaned the machinery may be used more effectively.

Jan 12, 1926

By J. R. Bridge, D. A. Vaughan

The phase diagram of the Zr-H system over the range 0 to 65 atomic pet was determined by high temperature X-ray diffraction methods. Results show a eutectoid between a zirconium and the hydride phase. The eutectoid temperature was established at 560±10°C with a eutectoid composition of 42*3 atomic pet H. The hydride phase of the lowest hydrogen content is stable only above the eutectoid temperature, but is formed and retained in a metastable state during reaction of zirconium with hydrogen at temperatures below 560°C. One hydride phase is indicated that exists over the composition range 55 to 65 atomic pet H. RECENT increase in the industrial importance of zirconium has stimulated several investigations of the reaction of zirconium with hydrogen. Review of the literature on interpretation of absorption isotherms' ' shows that attempts were made to relate the observations to the room temperature hydride phases reported by Hagg.3 However, more recently Schwartz and Mallett' reported the existence of a new hydride phase, isomorphous with the lower hydride in the Hf-H system described by Sidhu.4 This phase was found adjacent to the metal in a diffusion gradient sample. In addition to the new phase, Schwartz and Mallett reported on only two of the five hydrides found by Hagg. Gulbransen" confirmed the existence of only three hydrides of

Jan 1, 1957

By Robert E. Tally

CHAUNCEY L. BERRIEN, Butte, Mont. (written discussion).-Having had much actual experience with mine fires which have occurred or have been active in the mines of the Anaconda Copper Mining Co. during the past 4 years and having lately visited the fire zone of the United Verde mine with Mr. Tally, I wish to congratulate him for the success which he has had in controlling this fire and making the mine perfectly safe .for his miners. By this work he is not only keeping the property in operation but is reclaiming many lost orebodies. The ventilation system as described by him is practically the same as that used under my direction at the Mountain View mine fire in Butte in 1913 and at the Pennsylvania fire in 1916. This same system is at present being followed at the Leonard mine to extinguish a fire which has been active for 10 years although bulkheaded. The mining system in the Butte mine, at the origination of these fires was the same as that at the United Verde, namely, square setting .accompanied by the use of much timber bulkheading in the stopes owing to heavy ground. The pyritic content of the ore in Butte is not as high, but on the whole conditions have been the same, with the exception of actual location of the fire in the mine. I agree with Mr. Tally that flooding, the use of C02 or any gas, and the use of steam are all impracticable unless the fire zone can be absolutely sealed. His system of upcast escapement shafts in the fire zone, the use of bulkheads and fans to keep the gases away from the firemen, must be resorted to. By the method lie describes actual stoping may be carried on safely if started from the bottom of the fire and if the fire zone extends to the surface. In other words, the fire zone must be isolated from the rest of the mine by bulkheads and solid ground, with no ground above which can be damaged by spread of fire or caving. The serious fires in Butte have .occurred on or between levels in the mines where it was necessary to prevent their .extension upward, downward and laterally while the work of actually extinguishing them was in progress. This necessitated proper bulkheading should we lose control of the fire, the installation of ventilation similar to Mr. Tally's and the systematic drilling of holes with diamond drills for distributing water on the fire and around it.

Jan 12, 1916