Search Documents

By A. J. Jacobs

THE purpose of this note is to draw attention to a set of tables, recently compiled in Rocketdyne Research Report No. 64-19, under the title "Crystal-lographic Data for Indexing Cubic Twin Reflections and Cementite (Fe3C) Reflections in Electron Diffraction Patterns."' These tables were an outgrowth of electron-diffraction work conducted over the past several years on steels, precipitation-hardening aluminum- and nickel-base alloys, molybdenum, tantalum, and tantalum-base alloys. The first table lists the indices of possible twin reflections for all the possible twinning planes in bcc and fcc lattices. The twin reflections correspond

Jan 1, 1965

By C. B. Post, D. G. Schoffstall

A determinatioil of the hydrogen content of molten steel by means of the Vacuum-extraction method, as reported here, consists in first casting a sample of the bath in a bomb, so that the gases evolved during solidification are trapped for analysis. A portion of the cast steel sample is then prepared and heated at a temperature of 600" to 800°C. under high vacuum, and the gaser given off during this vacuum extraction (which are shown to be hydrogen), are collected and measured. Analysis of the gases evolved on solidification and the gases in the solid sample enables an accurate determination of hydrogen in the molten steel. Fig. I shows the bomb and accessories that have been found suitable for trapping the gases evolved on solidification. The bomb is made of scamless steel pipe, approximately 7 in. long by 136 in. i.d., and welded at the bottom. An ordinary pipe cap has a vacuuni-type metal stopcock threaded and brazed in its upper end. This pipe cap fits onto the bomb by means of machined threads. A flange is brazed to the pipe at the point where the cap starts to tighten up, and a rubber gasket is placed between the flange and cap. Heavy vacuum grease is used between the flange and gasket and the gasket and cap. The weight of the complete bomb and it? interval volume is known before the sample is cast. In practice, a sample of about 400 grams of steel is poured into the bomb, the funnel quickly swung out of the way, the bomb cap spun down the threads and tightened against the gasket, and the bomb set in a pail of water to keep the gasket and vacuum grease cool. It is estimated that at least 80 per cent 01 the gases evolved from the liquid sample during solidification are trapped in the bomb."

Jan 1, 1945

By J. O. Brittain, E. P. Lautenschlager, F. Felberbauer

This investigation was undertaken to evaluate the effect of a dispersed phase in a iron upon the strain hardening and the stress dependency of dislocation velocity as inferred from the strain-rate sensitivitv. Experiments were made in a-iron specimens with controlled amounts of carbon and/or A12O3. They were tested at various temperatures between 195' and 373 'K under a variety of conditions oj-concentration, strain rate, and quench aging. The resulting yield strength, flow strength, and strain hardening increased with addition of Al2O3. The parameter m, measured from changes in strain rate, was xsed to describe the stress dependency of the dislocation velocity. m was found to increase with additions of A12O3, increasing carbon in solution, and with increasing temperature. When applied to a recent model for yielding based upon dislocation multiplication and velocity characteristics, the values of m alone did not successfully predict yielding for the materials of this investigalion, but had to be adjusted with a consideration of the number of unlocked dislocations nucleated heterogeneously at discontinuities or inclusions. The change of yield strength with Al2O3 Interpar-ticle spacing appeared to obey a theory of Orowan. EVER since the concept of dislocations has been introduced to explain plastic deformation in crystalline materials, the origin of dislocations and the source of the number of dislocations required to account for plastic deformation have been persistent questions. Ruling out the possibility of homogeneous nucleation,' Gilman2 drew attention to the various cases of heterogeneous nucleation as the source of dislocations, whereas Frank and Read3 introduced the Frank-Read source. However, Gil-man found that the Frank-Read sources did not play a dominant role in the deformation of LiF crystals, but that small precipitates are often, if not always, associated with the nucleation of dislocations. In LiF crystals, however, most of the dislocations arose through the multiplication of moving dislocations in a mechanism described by Koehler4 and Orowan,5 Thus, relatively few precipitates could account for a large number of dislocations. A similar observation of dislocation nucleation at inclusions of precipitates was made by Stein and LOW' on Si-Fe crystals. Their crystals contained

Jan 1, 1964

By Irving M. Symonds

COMPAÑIA Minera de Peñoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Peñoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreón, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By Wayne E. Glenn

The San Miguelito Field of Ventura County, California, lies along the coast approximately five miles northwest of the city of Ventura. The structure is one of several in the Ventura anticline, a series of anticlinal folds trending northwest-southeast through the San Miguelito Field. The Ventura Avenue Field lies to the southeast along the anticline, and Padre Canyon and Rin-con Fields lie to the northwest; the series then extends beneath the Pacific Ocean. Production is obtained from the Lower Pico and Repetto formations of Pliocene age, and oil accumulation is controlled by faulting, lithology and structure. The first well in the First Grubb Pool was completed in November, 1931, and to date 48 producing wells have been drilled on the 276 productive acres. Approximately 685 ft of net pay are contained in the eight sand bodies grossing 1,220 ft of section. Production of oil to date has been 15,-600,000 bbl. A gas injection project was instigated in April, 1940, but was discontinued in September, 1949. This paper is confined to a discussion of the development and performance history of the First Grubb Pool of the San Miguelito Field. LOCATION AND GEOLOGY The San Miguelito Oil Field is located in Ventura County about five miles northwest of the city of Ventura along the coastal highway to Santa Barbara. It is located within sections 23, 24, 25, and 30 of Township 3 North, Range 24 West, San Bernardino Base and Meridian. Surface elevation in the field ranges from sea level to plus 1,200 ft, and the terrain is extremely rugged. The structure is well defined on the surface and on the wall of the Amphitheatre Canyon where appears a so-called "text book" anticlinal section. The San Miguelito structure is an asymmetrical, elongated anticline about two miles long and three-fourths of a mile wide. The trend of the axis of the anticline is northwest-southeast. Fig. 9 illustrates the contours and major faults of this structure. Dips on the southwesterly flank average about 40 degrees, whereas the northeasterly flank ranges from 60 to 75 degrees. There are several faults striking generally east and west. These faults do not appear to affect materially the area of accumulation or performance behavior. It is believed that accumulation was affected by steeply dipping beds and extremely low permeability of the northeast flank of the structure. As shown by the typical log, Fig. 1. the San Miguelito Field is divided into two stratigraphic producing intervals. The First Grubb Pool comprises the interval from the "G" to "L" markers; the Second Grubb Pool from the "L" to "M" markers. The First Grubb Pool, ranging in thickness from 1,105 to 1,680 ft, with an average of 1,220 ft, includes approximately 685 ft of oil-bearing sands. The First Grubb zone consists of eight sand intervals separated by shales. The shale bodies separating the eight sand intervals within the First Grubb Pool are continuous throughout the major part of the structure and serve as an effective barrier. Many of the thin, irregular shale or siltstone streaks within these sand bodies are discontinuous and do not affect well performance appreciably. The productive horizons in the First Grubb Pool are siltstones and sandstones of the Lower Pico and Repetto formations of Pliocene age. It is apparent from inspection of the typical log that the "G" to "L" interval might have been separated into at least six producing zones and selectively pro. duced. Unfortunately the electric log and some of our modern tools were not available or were in their infancy dur. ing the period 1931 through 1937. Not until 1937 when eight wells had been completed were there sufficient geological data to permit definition of the sand bodies. Then the problem of reservoir control in this multiple-sand field, where all sands are open to a common

Jan 1, 1950

By V. D. Perry

Mineralized breccia pipes, because of their widespread occurrence and close structural relations to some of the world's great ore bodies, are objects of unusual interest for mining engineers and geologists. The literature contains many references to them, but it is questionable whether their genetic significance and economic importance have been sufficiently emphasized. The purpose here is to stress these features, relating them to the field facts, for the particular benefit of younger generations of geologists who, confronted with and sometimes confused by the growing flood of geochemical, geophysical, and other specialized research approaches, may be reassured that mappable field relations remain a foremost guide to a better understanding of ore deposits. A mineralized breccia pipe is a pre-mineral, breccia structure which has controlled the circulation and deposition of subsequently introduced mineralization. It is composed of relatively rotated angular or rounded rock fragments, set in a mineralized matrix. A pipe in plan outline may be circular, oval or approach polygonal form, with a steep to vertical axis proportionately much greater than its horizontal dimensions. The pipe is a steeply plunging, chimneylike mass of brecciated rock cemented with later minerals. Rock breaks in a variety of ways and complete fragmentation often occurs without rotation of individual pieces. A finely broken rock mass may fit into a tight jig-saw pattern, each fragment having mutually concordant boundaries with its neighbors. The result is a stockwork of innumerable reticulating cracks that, once cemented by mineralization, forms a complicated intersecting network of individually insignificant but collectively important seams and veinlets. Stockwork fracturing among its many forms takes the shape of domes of subsidence, fracture pipes, and related peripheral zones around and over breccia columns, or a combination of any of these structures. The significance of the mineralized breccia pipe is that it represents the extreme or climactic expression of a structural type which has a variety of mutations including subsidence domes, fracture pipes, and other stockwork zones all with related ancestry and similar to dissimilar characteristics. These allied and associated structures hold an answer to the fundamental question of the origin of many important ore deposits. CANANEA-TYPE LOCALITY FOR BRECCIA PIPES The Cananea district is characterized by an unusual development of mineralized breccia pipes. It is an important copper producer located in Sonora, Mexico, a short distance southwest of Bisbee, Arizona, and at the southerly limit of the great porphyry copper belt of the southwestern U.S. Cananea's rocks consist of Paleozoic quartzite and limestone capped unconformably by a thick series of volcanics including andesitic flows, tuffs, and agglomerates. These rocks have been intruded by a deep-seated granite with related basic and acid differentiates including dikes and plugs of quartz mon-zonite porphyry. Mineralization coincides with a northwesterly trending belt of these intrusives which break upward into and through the sedimentary-volcanic rock sequence. The district has weakly defined tectonic alignments in a northwesterly direction with subordinate intersecting fracture elements, but lacks important faulting or fissuring to provide throughgoing avenues for the upward circulation of mineralizing fluids. Thus, as will be discussed in subsequent paragraphs, the alternate way in which late magmatic and hydro-thermal derivatives of the parent magma reached the near-surface zone was by excavating their own breccia pipe channelways. There are numerous stages of breccia pipe development, related both in time and space to magmatic activity. A compilation of similarities and differences in various pipes suggests that proximity or remoteness of a demonstrable or inferred magmatic source provides an orderly genetic basis for describing the following representative types. Cananea Duluth Type: There are no intrusive rocks within or close to the Cananea Duluth pipe; therefore, the existence of any deep-seated magma that may have been related to its formation must be inferred. The structure is an oval-shaped ring 1200 x 300 ft in plan dimensions, cutting steeply across low angle, bedded tuffs, and other volcanics; it has been developed by drill holes to a depth of 2000 ft below the surface. The ore follows the periphery of the pipe and is composed of intensely brecciated rock which is cemented by minor galena, sphalerite, chalcopyrite, quartz, carbonates, and adularia. There is a definite vertical zoning of sulfides with less galena, continuing sphalerite, and increasing chalcopyrite at deeper levels. Within the interior of the ore ring, the brecciation becomes progressively weaker and coarser, the whole indicating relatively gentle slumping with broken, thin tuff beds pre-

Jan 1, 1961

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

By H. W. Weart, S. Sarian

The effect of temperature, impurities, and capillarity on the morphology of solid particles in a liquid matrix is investigated. For the NbC-liquid iron system, at least, it is found that those particles which are dissolving will assume a spherical shape; all others will take the equilibrium shape. An aniso-tropic-isotropic transition in the interfacial tension is observed at about 1725°C and is believed to be due to cooperative roughening of the interface on an atomic scale. The presence of boron as an impurity lowers the transition temperature. It is the purpose of this paper to present some observations on the shape of particles in a system consisting of solid particles of nonuniform size in a liquid matrix and to propose an explanation for these observations. Although qualitative only, these observations, which were made largely in the course of a study of particle-growth kinetics,' are presented separately to draw attention to them. They reveal the effect of particle size, temperature, and surface-active impurities on particle shape in the solid NbC-liquid iron system, and are unique in demonstrating for the first time the reversible effect of temperature and impurity concentration on the anisotropy of the energy of the solid-liquid interfaces involved. Some of the changes are readily demonstrated with the few particles whose shapes can be clearly shown in a single photomicrograph, but others are more subtle, and their recognition depends upon some experience and the study of a much larger sample. For this reason, a certain amount of judgment must be acknowledged to underlie their detection, but every effort was made to maintain proper scientific objectivity in evaluating the observations. The observations will be presented first, and then an explanation rationalizing them will be offered. Brief reminders of the relevant theories will be inserted into the discussion at the appropriate points. EXPERIMENTAL The observations were made of the shape of NbC particles dispersed in liquid iron. All specimens were prepared by pressing NbC powder and car- bony1 iron powder treated according to standard powder-metallurgical procedures. Except as noted, all specimens were heated to 1900°C for 1/2 hr. In investigating the effect of temperature, specimens were quenched from 1900°C to various lower temperatures, and held long enough (48 hr) to allow shape changes to be completed. Boron, in the form of amorphous powder, and oxygen, in the form of niobium oxide powder, were added as impurities to some specimens. Nitrogen was introduced into some specimens as an impurity by heat treating the samples under a partial pressure of nitrogen gas. Effect of Temperature. It was first observed that increasing temperature had a marked effect in rounding the corners and edges of the particles. At 1900°C the particles are all very nearly spherical and remain so even when the holding time is extended to 48 hr. As can be seen from Fig. 1, there is virtually no evidence of the presence of low-index planes. At 1300°C, however, most of the particles are prismatic with very slightly rounded edges and corners, Fig. 2. (In making these shape comparisons, attention should be focused on the larger particles, even though the smaller ones would be expected to be the first to change shape, owing to the shorter diffusion distances involved. The cause of the mixed particle shape will be explored later.) It was established that these structures are re-

Jan 1, 1965

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped under the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton. Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand "Mincs Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all fecding into the same system. Capacity Installed Turbo Capacity Installed Steam-Tur- Station Alternators bine Dliven Centrifugal Compressors Brakpan............... Two 12,500-kw. sets Two 3,000-kw. sets Simmer Pan............... Six 3,000-kw. sets Rosherville................ Two 11,000-kw. sets Six 3,500-kw. machines Five 9,600-kw. sets Three 7,000-kw. machines Verckniging ............. Two 9,600-kw. sets Two 12,000-kw. sets 162,200-kw. sets Total steam-tkbine capacity installed, 204,200 kw. There are also at the Robinson Central air station six motor-driven centrifugal compressors, each of 3,500 kw., equal to 22,000 cu. ft. per minute at 120 Ib. capacity at 3,000 r.p.m. Power is supplied from these stations as 50-cycle, three-phase current generally at 40,000 volts,

Jan 1, 1916

HENRY A. VEZIN, Denver, Colo. (communication to the Secretary, February, 1897): I have read Mr. Austin's paper with considerable interest, more especially as the designing and study of such works have been an attractive occupation for me during the last twenty-five years. Mr. Austin says that a " plant on a terraced site has generally been considered the most advantageous," and also that " many advocate a level site," while he himself " is disposed to advocate a modification of the latter plan, utilizing an extended surface with a moderate slope."* Among the advocates of the terraced sites as against level ones, I do not recollect ever meeting a metallurgist who had even made an attempt to plan his works for level ground, or who had, in a lucid interval, figured how much he gained or lost by one or the other method. The average metallurgist starts with the assumption that it is rational to conduct his material down hill because its movement is aided by gravity, while to elevate ore or furnace-material by machinery he vaguely believes to be not alone wrong in principle, but also unnecessarily expensive. Let us look into the expense of elevating and see whether it really is prohibitory of the successful operation of smeltingworks on a level site. Hoisting or elevating material in the

Jan 1, 1897

By E. F. Johnson, F. H. Brinkman, H. J. Welge, A. L. Hicks

A method is presented for predicting the character of gas or water displacement in a radial system, which can be either horizontal or inclined. The latter case would comprise cone-shaped or dome-shaped symmetry. The method conriders the one dimension of radial distance, taken parallel to the bedding planes. Approximate allowance can be made for segregation of the two fluids perpendicular to the bedding planes. A complete saturation history can be obtained in about a day's time with the use of a desk calculator. Results of an example calculation agree well with the performance of simulated gas drive in a large model representing a section of a cone. This pie-shaped, sand-packed model was 8-ft long and 4-in. thick. The method of solution is useful in handling other partial differential equations of first order and first degree. INTRODUCTION A new analytical method has been developed for predicting the performance of gas or water drive in a reservoir having radial or cone-shaped symmetry (see Fig. 1). In addition, this new development offers a general method of handling partial differential equations of first order and first degree. This work extends those methods developed previously'- "or predicting the displacement of oil by gas or water in linear systems. The method of calculating oil recovery in a radial system involves two major parts. The first part is a calculation of the distribution of saturations at various times of depletion. The second part is the calculation of oil recovery and producing gas-oil or water-oil ratios through volumetric balance on the saturation distributions obtained in the first part. This second part differs only slightly in principle from similar calculations made with linear systems, for instance. The basic assumptions used in the calculations are as follows. 1. One-dimensional radial flow. An approach is explained later for approximating a second vertical dimension. (With- drawals of oil, and of the driving fluid after breakthrough, are assumed uniform around the periphery of the dome.) 2. Constant-volume fluid flow. Thus, in a gas drive there is no change in gas solubility, or in oil or gas volume due to viscous and gravity pressure drops. 3. Capillary forces are negligible. 4. Constant rate of injection. A program has been written for carrying out the calculations needed on a digital computer. However, a prediction can also be arrived at using a desk calculator; this latter method of work requires about a day's time for each prediction made. CALCULATION OF SATURATION DISTRIBUTION For definiteness, we describe the development of our method for the case of gas drive from the crest of the structure. The reader will note, however, that the method is just as applicable to an advancing radial water drive. The equation describing gas flow over an infinitesimal

By R. C. Hyslop

The object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: 1. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. Theequipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. Laboratory Procedure With these ideas in mind, the problem was approached in the manner in which Koenigsbergerl developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change in the magnetic field intensity AZ due to the proximity of a specimen is given by: mk AZ = 2a2 Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. r.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1946

By R. C. Hyslop

The object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: 1. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. Theequipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. Laboratory Procedure With these ideas in mind, the problem was approached in the manner in which Koenigsbergerl developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change in the magnetic field intensity AZ due to the proximity of a specimen is given by: mk AZ = 2a2 Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. r.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1946

By Y. Nakahiro

The removal of heavy metal compounds from a synthesized waste cyanide solution is achievable by a precipitation-flotation method. However, the differential separation of constituting metals by this method was thought to be very difficult. The present author found that addition of ferrous salt to the synthesized waste cyanide solution of cadmium and copper can modify the separation characteristics of these metals. In this paper, the separation of cadmium from copper in the synthesized waste cyanide water by the precipitation-flotation method is discussed. This differential flotation uses ferrous salt as a precipitant and sodium oleate as a collector. Based on a series of fundamental flotation tests, actual differential flotation tests were made. The separation of cadmium from copper in the synthesized waste cyanide water was found to be satisfactory. This method can be effective for the removal of difficult-to- separate colloidal precipitates from liquids by the sedimentation method, provided the applicability of this method to the separation of the other metals is promising. This consists of the intensive studies which have been conducted at author's laboratory.

Jan 1, 1980

By C. E. Wood, T. L. Joseph

This paper is a brief report of experimental work undertaken determine whether barium oxide in any quantity increases the desulfur ing action of blast-furnace slags. Industrial furnace operation wi slag containing small quantities of barium oxide, referred to later, intc ested S. A. Sanford of the Commercial Chemical Co., Youngstown, Oh to conduct experiments to furnish comparative results on desulfurizati with normal slag and slag containing small quantities of barium oxic The U. S. Bureau of Mines agreed to assist on the problem because the possible saving in fuel if the desulfurizing action of blast-furna slag can be substantially increased, also because the experiments woi yield new information on sulfur elimination in general, a matter economic importance in furnace practice. A more complete and func mental study of desulfurization of iron by slag is in progress. Distribution of Sulfur iN the Blast Furnace More than 90 per cent. of the total sulfur entering the blast furnz is in the coke. Sponge iron formed by reduction of iron oxides absor part of the sulfur as ferrous sulfide. Kinney's examination of sample taken from various levels of a 3004,011 furnace, shows that the me continues to take up sulfur until it reaches a level near the tuyer Desulfurization must therefore take place as the metal falls through t slag and as the slag and metal exist as layers in the crucible. The relative amounts of sulfur removed while the metal falls throu the slag and while the slag and metal exist as layers in t crucible are not definitely known. Preliminary experiments by t

Jan 1, 1929

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By H. H. Evinger, M. Muskat

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942