Search Documents

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a common occurrence in coal mines of the Northern Appalachian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and formation of cutter roof failure. In-mine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dikes registered the greatest amount of roof loading near the intersection of dikes with the rib. Load cells measuring horizontal pressure changes in the roof indicated that the greatest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysis of rock pressure monitoring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectively support the roof in areas of clastic dikes and prevent cutter roof failure. However, these methods were only successful when employed shortly after mining.

Jan 1, 1984

By W. Rostoker, S. Spachner

A N alloy of 50 pct Ni-50 pct Fe is currently manu- factured in tape thickness down to 1/8 mil. In the annealed form, this alloy produces an almost square hysteresis loop. This has generally been related to the fact that by proper rolling and annealing practice a sharp cube, (100) [OOl], texture can be developed. As part of a program directed toward an understanding of the relationships between magnetic properties and structure of tape core materials, analyses were made of preferred orientations in tapes of various thicknesses. Annealed tapes of this alloy in 2, 1, 1/2, ¼, and Y' mil gages were acquired from commercial sources. Pole figures constructed for the 2 and 1 mil tapes showed the expected sharp cube texture. However, the ½, ¼, and ? mil annealed tapes showed no evidence of any preferred orientations. A comparison of two transmission patterns is shown in Fig. 1. The origin of the absence of texture in the tapes of less than 1 mil thickness was explored in some detail. The basic questions were whether the heat treatment for the thinner tapes was wrongly selected, whether the initial cold worked textures were different, or whether the actual thickness of the tape exercised some influence on its annealing characteristics. Quantities of the five gages of tape were acquired in the as-rolled condition just prior to the final anneal. Pole figures of the cold worked textures were constructed for each of the tapes. Eye estimates of in-

Jan 1, 1956

By A. G. Guy, T. B. Lindemer

A second intepation of the Fick law has been developed and applied to three-place data generated from the Gosting and Fujita solution of the diffusion equation. This integration provides new mathematical techniques for the analysis of experimental data. Through use of the synthetic data it is shown that for concentration-independent interdifiusion coefficients these techniques permit a more accurate determination of the coefficients than does the usual Boltzmann-Alatano analysis. Another technique, applicable to the most general concentration-dependent diffusion coefficients , can be used to determine whether given sets of coefficients are consistent with the experimental ternary concentration-distance curves. DURING the past 10 years the subject of three-component diffusion has advanced from the stage of a laboratory curiosity to the status of an accepted portion of physical metallurgy.1 In the course of this development the underlying treatment for two-component sys- tems was extended and generalized to accommodate the added component, but fundamentally the analyses currently employed for ternary systems are analogous to those previously developed for binary systems. There are several indications that an improved analysis is needed for the ternary case. First, the two cross coefficients, D312 and D321 are typically an order of magnitude smaller than the direct coefficients and consequently are difficult to determine with adequate precision. Second, instead of a single concentration-penetration curve (as in binary diffusion), there are four such curves in the usual determination of ternary diffusion coefficients. These curves have definite theoretical interrelationships, but actual experimental curves exhibit significant departures from these relationships. Finally, the amount of data needed to adequately describe the diffusion behavior of a ternary system is so large that radically new methods are needed to facilitate the gathering of these data. ICirkaldy2j4 has proposed several possible analyses of ternary diffusion data, including some of the methods in current use. A "second-integration" procedure proposed by him4 differed in important respects from that presented here and was not carried to the point of application. Two other methods have been explored by the authors and will be published separately; these are a numerical analysis technique and a method for the analysis of a single ternary diffusion couple. Still other analyses are being explored by various investigators. At present it seems likely that the final analysis of ternary diffusion that evolves will be a composite

Jan 1, 1968

By P. D. I. Honeyman

Changing trends in concentration, involving regrinding with the subsequent production of a finely divided, high-grade flotation product, presents a real problem to the modern copper smelter. In the treatment of such a material, handling difficulties are numerous and potential possible losses may be very great. In many plants, of course, preliminary roasting of the furnace charge remains an economical necessity. Under such circumstances, the operator has no alternative except to follow orthodox roaster reverberatory practice, though taking all possible precautions to avoid excessive dust losses and bad working conditions. In other plants, roasting is not only unnecessary but would be highly undesirable, and at best the charge would be merely dried before entering the reverberatory furnace. In the latter case the possibilities of raw charging loom large. The Miami plant of the International Smelting Co. handles the entire output of concentrates of the several mining companies operating in the Globe-Miami district. All of these companies produce a flotation concentrate which, at the Miami Copper Co. particularly, is all reground and is high in grade. In addition, the Inspiration Copper Co. ships a substantial tonnage of high-grade cement copper to the smelter from its leaching plant. Following the flow sheet of the original plant, all such material received was bedded, dried in Wedge furnaces and smelted in reverberatory furnaces. At times during the history of the plant it has been necessary to carry the drying operation further, to a partial roast, before reverberatory smelting. Since the charge contained over 80 per cent flotation concentrates, the handling of which in a dried condition was at best a dusty job, unusual precautions were taken to cut down dust losses. The Wedge furnace plant was equipped with a Cottrell treater and all hoppers and calcine cars were carefully designed to cut down dust loss in transferring the so-called calcine from hoppers to car and from car to furnace. In the furnace itself the dusting problem was a severe one. Arch erosion was very rapid and flues and waste-heat boilers rapidly filled up with a partly smelted flue dust.

Jan 1, 1934

By Thomas L. Wright

Exploration activities were maintained at a high level throughout 1966. Numerous significant discoveries and developments in which geologists played an important part were announced. Although the complete results of exploration activities carried out during the year by private companies have not been announced, the following are among the more important developments that have been made public knowledge. In the western states, exploration for practically all of the metals continued at a high rate. Substantially increased interest in uranium occurred this year, and it is felt by many that a real boom in the demand for uranium may come about in the near future. The reasons have been the more rapid acceptance of atomic power than had been anticipated, and that uranium producers can now sell their product to private interests and even foreign countries. A tremendous demand for uranium is anticipated by many, and this has rekindled exploration activity. On the Colorado Plateau, in Wyoming, and in the area around Grants, N. M., a number of companies have undertaken uranium exploration programs, among which are Kerr-McGee, Homestake, Anaconda and Utah Construction. A new uranium orebody in Texas was brought into production early in 1966 by Susquehanna Western.

Jan 2, 1967

By W. F. Carew, F. A. Crossley

Tensile, creep-rupture, and stability tests were employed to evaluate the effect of a-strengthening and ß-complexing additions on the base composition Ti-6Al-3Mo. The ultimate objective was to produce an alloy of greater strength than the Ti-7A1-3Mo alloy. Strengthening of a was accomplished by additions of 2 and 4 pct Ge, 4 pct Sn, 4 pct Zr, and 2 pct Sn-2 pct Zr. Making the ß more complex while keeping the total of ß-stabilizing additions constant at 3 pct resulted in higher tensile strengths but lower creep and rwpture strengths, especially at 1000°F. None of the more complex versions of the base alloy offers greater promise than the Ti-7A1-3Mo alloy. However, some improvement in the strength of the latter may follow from additions of zirconium perhaps up to 4 pct. PREVIOUS work directed at the development of titanium-base alloys with: 1) minimum room-temperature tensile elongation of 10 pct in 1 in., 2) high creep resistance at elevated temperature, and 3) the ability to retain original room temperature tensile ductility following exposure to creep conditions at elevated temperatures, demonstrated Ti-Al-Mo ternary compositions in the range 5 to 7 pct Al-3 to 6 pct Mo to be the most promising. Of this group the Ti-7Al-3Mo alloy was the strongest.'-= The objective of the present work was to determine if alloys of this type could be further strengthened by making additions which dissolve preferentially in the a-phase and by making the ß-phase more complex. For this study the base composition Ti-6Al-3Mo was selected rather than Ti-7Al-3Mo in order to minimize the possibility that in a more complex alloy with a-strengthening additions, low ductility might obscure the strength contribution. The metals

Jan 1, 1959

By Carl E. Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. CHARACTERISTICS AND REQUIREMENTS OF SOLDERS IN GENERAL General Physical Properties.-When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.-The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

Jan 1, 1928

By C. E. Agnew

The Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P. Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formerly he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By C. E. Agnew

The Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P. Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formerly he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By William Schriever

The flow of a gas-free liquid through a spherical-grain sand has been investigated by S1ichter.l By theoretical considerations involving a rather large number of approximations he arrives at the following flow-formula: V = CPd2At NLB{1 - m) where V is the volume of liquid delivered in time t through a cylindrical column of sand of length L and cross-sectional area A by a pressure-drop P when the sand grains of diameter d are packed to a porosity m and the coefficient of viscosity of the liquid is n. C and B are constants which were determined from geometrical relations; B was in reality a function of . Values of B(l — m) for various values of m were given in a table. In the same Annual Report of the U. S. Geological Survey, King reported the results of his experiments on the flow of water through porous media. He found that there was a departure of about 86 per cent. from a linear relationship between rate of flow and pressure, for a specimen of Dunnville sandstone for pressure drops not exceeding 60 cm. of mercury. The specimen was approximately 4 cm. in diameter and 5.1 cm. in length. Over the same range of pressure he found a departure of 45 per cent. for a specimen of Madison sandstone. For unconsolidated sands he found departures as great as 49 per cent. for pressure drops of 70 cm. of mercury; for pressure drops not exceeding a few inches of water he obtained a close approximation to a linear relation. He also investi-

Jan 1, 1930

By William F. Blake

The discovery of tin-ore in the Black Hills of Dakota dates from June, 1883, and short preliminary notices were published in September of that year.* The discovery-point is known as the Etta Mine, in the central portion of the Hills, about six miles east of

Jan 1, 1885

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By Sage B. H., Lacey W. N., G. W. Billman

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By Sage B. H., G. W. Billman, Lacey W. N.

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

In traversing lately the Sierra Madre, west of Sail Pedro and Guanacevi, I estimated the topographic summit at several points, by aneroid barometer, at about 8,500 ft. Mr. Weed's measurements, 40 miles further north, are from 9,000 to 9,500 ft., and indicate the correctness of the impression I obtained at the time, namely, that the greatest movement in the elevation of the Sierra was between Guanacevi and Guadaloupe y Calvo. This is suggested also by the course of the headwaters of the Rio Conchas and of the Nazas, and by the relative corrasion of the branches of the two streams. Mr. Weed's statements as to the unevenness and great relief of the andesite floor underlying the later dacites and rhyolites are very interesting, and lead me to add that the floor of the andesite breccias and flows is uncovered for several square miles east of Guanacevi. This floor is of reddish, bluish and gray shales, lying horizontal or dipping slightly east. Their age is unknown; but from the interbedded occurrence of copper sulphides, I took it to be Triassic,

Jan 1, 1903

By Jonathan G. Price

Silver-copper-lead deposits In Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore in overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulflide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1984

By C. Alstetter, V. Kerlins

By using alloys with subzero Ms temperatures, this investigation demonstrates that the amount of decomposition of martensite during the quench from austenite may be considerable and especially so in specimens of large cross -sections and high Ms temperatures. The activation energy for decomposition as measured dilutometrically is PREVTOUS investigations of the initial decomposition of Fe-C system martensite have invariably been limited to alloys having M, temperatures above a function of the amount of transformation which has taken place. The amount of transformation is a linear finction of log time. A correction term to the activation energy is derived for dilatometric measurements in which no end-point of the transformation is detected. room temperature. In such alloys the martensite is tempered during the quench to an extent dictated by the quench rate and temperature of formation. This tempering, called quench-tempering, Q-tempering, self-tempering, or auto-tempering, although frequently acknowledged, has not been studied or treated quantitatively. To do so one should obtain absolutely untempered martensite and study its decomposition. This as-formed martensite could be obtained either by extremely rapid quenching, requiring very thin specimens, or by lowering the martensite formation temperature range. The second alternative is more effective, because

Jan 1, 1963

By K. E. Beu

THE integrated intensity X-ray method of meas-uring retained austenite concentrations in hardened plain carbon or low alloy steels as proposed by Averbach and Cohen1,2 has the advantages of being a highly sensitive and precise quantitative method. The various phases of this method have been studied and several modifications have been developed which aid not only in reducing the time required per determination, but which also increase the possible accuracy of the method. A fundamental step in the original calculation procedure is to plot V.A(?) curves for austenite and martensite and to obtain VM/VA ratios from these curves.' In taking this ratio the absorption factor A (8) drops out since it is constant for a. given diffraction angle 8. The reason for eliminating A(?) in this manner is because it is apparently assumed

Jan 1, 1953

By R. W. Diamond

Three mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the St. Eugene Concentrator, Moyie, B. C., and (3) the Tadanac (Customs) Concentrator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals —lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential flotation.

Jan 1, 1928