Search Documents

By S. Frederick Ravitz

FOUR liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constit-uents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equi-librium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest.

Jan 1, 1936

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington' have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4' and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick's law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.' By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.' (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick's law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By R. T. Webber, B. B. Owen

THE vapor phase deposition of molybdenum and tungsten from the hexacarbonyls has been thoroughly investigated by Lander and Germer1 and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2.3 could be similarly deposited, but did not investigate this metal extensively. Recently,4 conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. APPARATUS AND TECHNIQUE The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T2 and T3 containing crystals of the carbonyl. T2 is kept in a constant temperature bath (not shown), while T3 is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Ss, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by S5 is used to determine the volume included by S4, S6, Se, S10, the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: I, the specimen temperature, from room temperature to about 1000°C, 2, the carbonyl vapor pressure, from 40 to 220 microns, and 3, the hydrogen flow. In several runs, 0.8 to 1.8 pct of hydrogen sulfide was introduced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1948

THE CHAIRMAN ( F. K. COPELAND, * Chicago, ,Ill.).-This is an interest-ing and very troublesome proposition to all of us. Ten or fifteen years ago, when the old-fashioned idea prevailed that a man was responsible for his own health and safety, that if anything happened to him it was his own lookout; we got along without this problem; but with the advent of accident compensation, with the agitation that there is all the time for pensions, sick benefits, and the responsibility of a company for the health of its employees, whenever you take a man on, that phase is becoming more and more important. One cannot afford to hire a man who is blind in one eye, even though he may have perfect sight in the other eye; if he loses that one eye, if lie becomes a total disability, the company is liable for the man's complete sight. Another thing that should make us particularly interested in this problem is the fact that the unions are very much opposed to it. One of the requirements of this steel unpleasantness is that the companies abandon their physical examination of employees. It is a very difficult problem to examine 400 or 500 men as intelligently as possible and decide whether a man on this or that side of the line is accepted. T. T. READ, Washington, D. C.-The United States. Bureau of Mines has in progress at the present time a study of the effect of underground atmospheric conditions on the safety and health of the workers. Im-proved methods have been employed and it is an excellent and ex-tremely valuable piece of research work.

Jan 12, 1919

By Vincent Gianella

Barite deposits are of widespread occurrence in Nevada but there are few pro-ducing properties; most of the latter are in northern Nevada. The production of the state is small at present-in the neighborhood of 15,000 tons annually-but is steadily increasing. The barite occurs in veins and also as replacement deposits in lime-stone. The bulk of the production has come from the replacement deposits. It is thought that the barite was deposited from rising hot waters similar to-and probably contemporaneous with-those responsible for some of the metallic ores of the state. This paper discusses only the deposits in northern Nevada. THE commercial mining of barite did not begin in Nevada until 1916 but although the production has been small there has been a rapid increase in tonnage during the past several years. Barite is widely distributed in the state and production comes from at least nine of the seventeen counties. Apparently this is not generally known, as only two counties are mentioned in a recent publications dealing with barite. The increase in output is due largely to recently discovered barite deposits in northern Nevada. The principal production has come from the northern portions of Lander and Eureka counties; smaller amounts from Elko County. The discussion in this paper is confined largely to the deposits in these counties. Most of the producing area is tributary to the Western Pacific and Southern Pacific Railroads, whose tracks lie along the Humboldt River. Barite is known from other northern counties but so far the production has been small. The output has come entirely from veins and replacement deposits, the latter largely in sedimentary rocks. In general, the barite from veins is white; that from the replacement deposits usually is dark gray to black, although some is light gray or white. Most of the veins contain sulphides and many barite-bearing veins have been worked for their content of base or precious metals.

Jan 1, 1940

J. C. WRIGHT.-The problem of organizing and maintaining a vocational class for those employees who are engaged in the mining industry depends on several most important factors. The first is the sympathetic cooperation of employer and employee; the second is to find the subject matter that must be presented to these men; and the third is to find the instructor who can present that subject matter. This is perhaps the most difficult, for we usually find a man who knows the material that is to be presented but is not a teacher or does not know how to organize his material. The man must know the subject matter from the standpoint of absolute contact with industry in order to be a successful teacher. I have come into contact with two kinds of schools organized in connection with mining occupations. In one type the instruction leans very largely toward elementary subjects, arithmetic, reading and writing and spelling; it is not of such a character as to help or improve the working man in his occupation in the sense that we are attempting when we speak of vocational education. In the other type of school, an engineer is usually employed as a teacher. He immediately begins to give the things with which he is most familiar and the instruction becomes such as only those who possess a high-school or college education, perhaps, are able to receive. In between these two schools is the school we are trying to, promote, a school that will meet the needs of those employed. MARGUERITE W. JORDAN,* Altoona, Pa. -Vocational education has become the business man's problem; for he is the keeper of that white elephant, labor turnover, and anything that will decrease the size of the monster is worthy of serious consideration. This vocational education can do; for it can supply many of those deficiencies in upbringing and. environment that make for the discontent and restlessness of our varied classes of unskilled labor: the Anglo-Saxon mountaineer; the Southern negroes who have crossed Mason & Dixon's line by the thousands, "searching satisfaction for our minds;" and the still greater number who have sought across the sea America, "the promised land.

Jan 4, 1919

By Irwin Roman

IT has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maxi-mum electromotive force will be devel-oped when the axis of rotation is perpen- dicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, FIG. 1.-MAGNETIC GRADIOMETER. it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the inten-sities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By C. G. McLachlan

ONE phase of the treatment in sulphide flotation, covered generally in a review of pulp pretreat-ment by S. A. Falconer,' is the matter of grinding mills as conditioners, a subject on which further study could be advantageous. Flotation with few exceptions is preceded by grinding, and the grinding and flotation capacity required for the treatment of an ore is based generally on laboratory or pilot mill tests. The results of such tests, it then is assumed, will be duplicated in practice, and a flowsheet is prepared on that basis. This assumption may be too broad, because in several instances laboratory flotation tests made on massive sulphide copper ores could not be duplicated in plant operation without the introduction of an aeration step, either in closed circuit with the grind-inging mills, or between grinding and flotation.~' " The differences between laboratory and plant grinding practice are considerable, and may be summarized as follows: 1—In the laboratory a relatively fine charge is ground in a batch mill. In the plant, the feed, usually considerably coarser than the ore tested in the laboratory, enters the grinding mill continuously and more often than not, oversize material in the mill discharge is retained in the grinding circuit by a classifier until the required degree of reduction has been effected. 2—The rate of grinding in the laboratory is slower than in plant practice. 3—The percentage of volume occupied by the pulp in a laboratory mill rarely approaches that of a continuous overflow type mill. This does not apply if the comparison is made with grate type mills, but in that case an even wider discrepancy between the relative rates of laboratory and mill grinding almost invariably exists. The present trend in grinding is toward larger mills to reduce the number of operating units. This accentuates the foregoing differences. It is believed that the trend toward larger mills is sound, but that when large mills are used, metallurgists should check their flotation circuits carefully to determine whether laboratory tests are being reproduced in

Jan 1, 1952

By J. F. Crouch

INTRODUCTION Roll front uranium has unique geologic characteristics (L,) which require specialized mining procedures. Roll front uranium occurs in arkosic sandstones with the ore zone typically less than 100 feet in thickness with up to 400 feet of overburden. The areal extent of ore is often a few thousand acres. Within the ore zone, ore grade material occurs in C and S shaped rolls, which are a few feet in width and height but may run laterally for several hundred feet. Since the total mine plan may include mining all ore, a roll front uranium mine may cover a few thousand acres. For both economic and environmental reasons, a roll front deposit is mined as a series of phases or sub-pits (3, 4) as illustrated in Figure 1. A typical sub-pit is 400 to 500 feet across. Sub-pit 1 is stripped initially and the overburden is spoiled on the surface. Depending on haul distance and overburden characteristics, stripping is done with trucks and shovels (or front-end loaders) or scrapers. When ore is encountered in sub-pit 1, mining begins, and the stripping equipment is moved to sub-pit 2, with sub-pit 2 overburden also being spoiled on the surface. When ore is encountered in sub- pit 2, sub-pit 1 mining should ideally be complete so the mining equipment can move to sub-pit 2 and sub-pit 3 overburden can be spoiled in the mined out sub-pit 1 area. Ore is mined selectively in a series of 12 to 24 inch cuts by a 2-1/2 yard backhoe on the basis of radiometric probing. For effective drainage, ditches must be maintained on the boundary of sub-pits, and mining lifts are kept as level as possible, with the orebody slightly elevated as part of general good mining practice. Waste removal in the ore zone is done by self- loading scrapers near the orebodies and by push-pull or push loaded scrapers away from the orebodies. Each self-loading scraper cut is

Jan 1, 1983

By Albert Arents

This test is based upon the fact that metallic copper will precipitate gold and silver upoil its surface from acid solutions. Of course, the fact is not new, but its application is probably so. I have used the method with success; it recommends itself by the rapidity and ease with which it may be carried on. An auriferous cyanide solution, if made acid with sulphuric acid and boiled with finely divided, pulverulent, metallic copper, will, within a short time, deposit its gold-content on the copper. Any silver in the solution is also precipitated. If this mixture is now filtered, the filter and contents may at once be subjected to a crucible assay treatment, and its lead buttons cupelled and determined. If, instead of taking cement-copper, or any metallic copperpowder, a solution of bluestone is used after acidification, and a few small pieces of sheet aluminum are added, and the solution boiled until all the copper has come down, the result as to the precipitation of gold and silver is the same. This modification takes more time and attention in boiling. If aluminum has been used, it should go into the crucible with the filter and

Jan 1, 1904

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By L. A. Bromley, R. L. McKisson

A high temperature calorimeter designed for use up to 1500°K is described and the theory of its operation presented. This calorimeter was used to measure the heats of formation of Na-Sn alloys ranging in composition from tin to Na2Sn. The values tend to support those reported by Kubaschewski and Seith. ONE method of obtaining the heat of formation of an alloy is to measure the heat of mixing of the elements at high temperature. The principal advantage of this method is that the desired quantity is measured directly, while in conventional room temperature methods the differences of the heats of solution of the elements and the alloy in a suitable solvent are measured. A method of improving the accuracy of the high temperature measurements, when the precision of the measurement is lower than that of the heat capacity values for the elements, is to add one component at room temperature to the other at the high temperature, so that part of the heat of reaction is dissipated in heating the cold component to the high temperature. Thus, only a fraction of the heat of reaction is measured, and a result of higher precision is obtained. The limitations of the high temperature technique are that volatile systems cannot be studied, and that many alloys melt at temperatures higher than those at which the calorimetric apparatus operates readily. Nevertheless, a calorimeter operating at 1500°K would be useful in investigating many of the lower melting alloy systems and the low melting mixed oxide systems. A unit designed for these applications was built and is described here. The Na-Sn system was chosen for investigation because the temperature involved, 880°K, would adequately test the operation of the calorimeter. Further, the data reported in the literature for the various alloys of sodium and tin differ markedly, and it was hoped that this investigation would help to fix the values of the heats of formation in this system. Design of Apparatus A detailed discussion of the considerations involved in the calorimeter design is given by Mc-Kisson and Bromley,' and a brief summary follows. Fig. 1 shows a sectional view of the calorimeter. The inner graphite chamber is maintained at constant temperature by means of the circulating molten tin bath in which it is submerged. The tin is contained in a graphite vat. This unit comprises a thermostat whose heat capacity is about 7000 cal per "C. The main heating element consists of a machined graphite spiral with a room temperature resistance of about 1/2 ohm. These parts are separated from the powdered carbon external insulation by the cage, a cylindrical graphite chamber. The electrical insulators and separators, the auxiliary heater spool, and the loading tube liner are made of sintered alumina. The tin vat stirrers, the sample stir-rer, the melt thermocouple well, and the power leads are made of molybdenum. The auxiliary heater is wound with molybdenum wire and serves to compensate for the heat loss up the loading tube. All of the individual components in the high temperature region of the calorimeter will withstand at least 2000°K, and the various contacting materials should easily withstand 1500°K. The external container for the insulating carbon powder is a copper shell upon which copper tubes are soldered to serve as cooling coils.

Jan 1, 1953

By C. Y. Ang, C. Wert

Quench aging of supersaturated solid solutions of nitrogen in columbium takes place in reasonable times in the temperature range 300&apos; to 500°C. Changes in internal friction, hardness, and electrical resistivity are found to accompany this change. THERE is practically no detailed information in the literature concerning interstitial solid solutions in either columbium or tantalum. The fact that both of these metals are used extensively commercially in both pure and alloyed states makes studies of their properties of value. While the plan is to study both these metals and their alloys extensively, so far only a small number of measurements have been made. This paper presents data obtained in the initial investigations of columbium. The principal interstitial impurities of columbium are likely to be hydrogen, carbon, oxygen, and nitrogen. The first of these, hydrogen, is outside the scope of internal friction measurements at present and nothing quantitative is known about the initial hydrogen content of the specimens. However, it is believed that it is completely absent after the preliminary heat treatments are carried out. The carbon content of the original samples is low and can be reduced still further during sample preparation. Oxygen is normally present to some extent in columbium and can also be added or removed easily. Nitrogen is also normally present in small amounts and can also be controlled within limits. Since it is not possible yet to remove all the nitrogen from columbium and since it is possible to remove essentially all the oxygen and carbon, initial measurements were made on the alloy system nitrogen in columbium. In this sense then, the alloys are true binary alloys. Little is known about the effects of nitrogen on the physical and metallurgical properties of columbium, so it was necessary to perform some rather elementary measurements on the specimens. These measurements are described briefly in the next section and are discussed in detail in later sections. Scope of the Work That internal friction is associated with diffusion of nitrogen in columbium has been known for some time. It is similar in nature to that for carbon and nitrogen in a-iron. In these latter cases, the information obtained from internal friction has been useful metallurgically.&apos; and it is not too much to expect useful information from similar studies on columbium containing nitrogen. The technique of internal friction measurements is adequately described by Ke2 At a frequency of 1 cps the internal friction peak for nitrogen in columbium occurs at 300°C and that for oxygen at 160°C." So that all the measurements will be meaningful metallurgically, the internal friction has been calibrated by making a measurement of the damping at the two peaks and a measurement of oxygen and nitrogen content by chemical analysis. A comparison of the two gives the following calibration factor: To go from damping capacity expressed in terms of 1/Q to weight percent of oxygen and nitrogen in solid solution in columbium, multiply the peak values of internal friction by about 4 and 3 respectively." Data from which these factors were calculated are presented in Table I. The increase of electrical resistance of columbium caused by the addition of oxygen and nitrogen as interstitial impurities has been quantitatively determined. At room temperature the percentage increase is small for small additions of impurities (<0.1 wt pct); as the temperature is lowered it becomes an increasingly larger factor of the total resistance. An empirical relation has been established to express the resistivity at — 195°C in terms of weight percent of oxygen and nitrogen in solid solution. It is easy to make supersaturated solid solutions of nitrogen in columbium and to observe aging phenomena. The optimum aging temperature, as in the case for carbon and nitrogen in a-iron, occurs at the temperature for which the time necessary for a single place-change in diffusion is about 1 to 10 millisec. This means for nitrogen in columbium that significant property changes should take place for this alloy at about 400" to 500°C in reasonable time intervals. Results of such aging experiments are

Jan 1, 1954

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the hest of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but call vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no imrncdiate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By L. L. Brundred

The major portion of the production of the Gulf Coast area, represented by South Texas and South Louisiana, comes from the flanks of well-defined salt domes. This oil, containing an excellent lubricating stock, ranges from 17° to 28° Be. gravity. Some lighter oil is encountered but the life of such fields is, in general, an open question. In fact, there are few light-gravity fields which have proved of much value. In all of the fields water encroachment, or, more properly, water produced with the oil, is a vital factor. After the first head of high-pressure gas is removed, ever-increasing percentages of water appear, and naturally the life of the wells is materially affected thereby. The sands are, as a rule, extremely fine, very soft, and must be carefully excluded from the hole by the use of fine screen to prevent sanding up. All sands are tipped at such extreme angles as to make coring essential for the location of water strata, oil-bearing sands and important shale. beds. Even with modern coring, the correlation of logs is a difficult problem. Due to the fact that the bulk of the oil is refined for its lubricating properties, little attention has been paid to losses by evaporation in the field. This is largely influenced by the fact that the major companies have set a price schedule, showing but two grades, "A" and "B." The average oil company, therefore, does not attempt to use the gas-lift but relies primarily on the air-lift and then only on wells considered to be particularly adapted to its use, namely those capable of producing large quantities of fluid and yet not having sufficient "kick" to flow. Furthermore, as the gas contained in the reservoirs is mostly ricthane such gas being very quickly vaporized and produced in large quantity in the early life of the fields, there is little gas left after the first flush flowing period of the wells. In fact, it is very generally conceded that gas is a precarious fuel to depend on in any of the coastal fields. This situation largely accounts for the fact that air, as the lifting medium, is almost universally used. In the average field, wells are drilled on the flanks of the domes in close proximity to one another, largely on account of the extreme dips of the formation and "town lot" leases, and space to set up machinery and

Jan 1, 1928

By G. S. Rice

IT is evident from Professor Louis&apos; remarks that he holds a different opinion on certain phenomena connected with a specific type of surface subsidence from mining than is held by many engineers in the United States. The question which appears to be at issue is whether or not the line or plane of "draw" produced in ground movement resulting from extraction of pillars may, under certain conditions, be vertical or even inclined toward the workings rather than inclined for- ward over the unworked mineral, as it is universally agreed occurs in mining by the longwall advancing method. In discussing this case it is well to take the simplest condition, such as specified by Professor Louis, of a flat bed, whether it be coal, iron or other mineral, where the overburden is stratified rock and where there is no overlying quicksand. Professor Louis says in effect that his experience is that the ultimate angle of draw is always positive and inclined 5" to 15" from the perpendicular over the unwrought mineral. My experience under Illinois coal-mining conditions is that .&apos;where longwall advancing is used the draw is always positive as Professor Louis describes it, but that in extracting of panels by withdrawal of pillars, the ground movement is manifested, after the first roof&apos; beam break, by the forming of an unstable dome over the goave. Then subsequently, by the falling of individual slabs from the under side, the dome gets larger and higher until it breaks through to the surface of the rock., Up to this time, arch stresses buttress the rocks above the solid coal or mineral. When, however, after. the dome breaks through and the central hole - #enlarges so the arch is no longer sufficiently supported -the stratified rocks cantilever out .from over the solid unworked mineral and tend to break off in masses triangular in vertical cross-section, until the broken loose material, sliding down against the solid rock, .has such a thrust that it balances the tendency ,for the solid stratified rock to break away and slide toward the excavation.

Jan 1, 1929

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

"Coulter's Rainbow and Crooked Falls are situated about five miles below the City of Great Falls. Coulter's, the first of the series in the course of the river, is unimportant and has been submerged by the Rainbow dam. Next below Coulter's is the Rainbow Falls, 47 feet in height. Following Rainbow Falls is the Crooked Falls, 21 feet in height. The power developed at this point is such that the one clam, power house and tail-race utilize the power from all three of the above falls.The development at Rainbow was started October, 1908, and completed July, 1910. It has a total capacity of 21,000 k-w. in generators, and 36,000 h-p. in waterwheels, and operates at 105 foot head. The general scheme of development is typical of what may be called standard practice in the west for plants of medium head, and consists of a low diverting clam, a double pipe line feeding into a balancing reservoir near the plant, and individual pen-stocks supplying the turbines from this reservoir.The dam is a rock-filled crib structure 1,146 feet long and 29 feet high, the up-stream side of which slopes at such an angle that the stability of the clam is assured even under the greatest floods, the weight of the water acting to hold it down, so that the higher the flood the greater the stability. The down-stream side is also sloping and tapers off into a long apron so designed as to take care of any overflow which may occur without shock or commotion. The clam is founded on solid rock throughout its entire length."

Jan 1, 1913

By J. T. Cherry

A fundamental goal of the Plowshare Program is to predict crater dimensions when an explosive of known yield is buried at a given depth in a given medium. In this paper a technique is presented that seems to calculate adequately, from first principles, the mound and cavity growth that occur during nuclear and high-explosive cratering events. The technique features a standard, numerical approach to high- intensity stress-wave propagation coupled with a unique model of material behavior in brittle failure. A schematic of stress-wave propagation is presented in Fig. 1. The equation of motion provides a functional relation between the applied stress field and the resulting acceleration of each point in the medium. Accelerations, when allowed to act over a small time increment [A]t, produce new velocities, velocities produce displacements, displacements produce strains, and strains produce a new stress field. Time is incremented by [A]t, and the cycle is repeated. The time increment [A]t is determined by an independent stability condition which requires the increment to be smaller than the time necessary far a compressional wave to travel across the smallest zone. We assume that failure occurs in a brittle material when either the tensile strength or the maximum allowable strain energy of distortion is exceeded. When either of these two conditions is violated, the code uses the cracked equation of state to determine the stress. A preshot testing program is used to determine the consolidated and cracked equations of state. In situ properties to be determined by field logging are density and elastic velocity (compressional and shear ve-

Jan 1, 1967