Search Documents

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By Kenneth A. Moon

An exact statistical treatment of a one-dimensional model is used as a basis for evoluating the reliability of certain simplified expressions for the activity of the solute in interstitial solutions, including one obtained from the exact expression by setting the repulsive interaction equal to infinity. The latter approximation is found to be satisfactory at low and moderate concentration if the repulsive interaction is large, even though not infinite. A similar expression (identical if the co-odination number is two) is derived from the quasichemical expression of Lacher, and is recommended as the best available expression for the excess configurational entropy of interstitial solutions with excluded sites. Some reasonable models are discussed, and the nature of the saturated solutions is determined by inspection. Some of the models reduce to the one -dimensional case. An analysis is given of the excess partial entropy of hydrogen in V-H; Nb-H; and To-H solutions. MOST treatments of the statistical thermodynamics of interstitial solid solutions have followed the classic paper1 of Lacher in making the simplifying assumption that the configurational entropy of the solution is ideal. However, it is becoming increasingly apparent that there are many interstitial solutions with very large so lute-solute repulsions, and for these the assumption of ideal entropy is not valid or useful. It is important to realize that with substitutional solutions large repulsions between the component atoms must lead to phase separation, whereas in interstitial solutions the free energy of the solution is not drastically increased by large solute-solute repulsions until intrinsic saturation is reached at the concentration where further solute would be forced to enter a site in which it would experience the repulsive effect of one or more solute atoms already present. In the limiting case of an infinitely large repulsive interaction, the excess free energy would be attributable entirely to excess entropy, the enthalpy of mixing being zero. AS will be shown below, even if the repulsions are less than infinite, a treatment based on an assumption of infinite repulsions may be very satisfactory up to moderately high concentrations of the interstitial component. Often in solutions where large repulsive interactions exist, there are also small interactions — often attractive—between solute atoms in configurations other than that corresponding to the large repulsion. In such cases the excess free energy will consist of an excess entropy term attributable to the large repulsive interactions, and an enthalpy term corresponding to the other small interactions. Nomenclature to differentiate succinctly between important cases would be a convenience. In this paper the nomenclature shown in Table I will be used. In Table I, and in the preceeding discussion, excess quantities are defined in terms of standard states which are pure solid solvent and pure (possibly hypothetical) solid saturated phase of the structure in question. In practice, it is more convenient to choose the interstitial element as a component, and its conventional standard state. This will add a composition-independent term to the excess entropy and the enthalpy. The earliest paper known to the present author which treats the thermodynamics of athermal interstitial solutions was given by schei12 in 1951, but the statistical derivations in that paper are open to criticism. Speiser and Spretnak were the first to give a correct statistical treatment,3 limited, however, to concentrations sufficiently low that the number of empty sites excluded from occupancy by more than one filled site is negligible. The purpose of the present paper is to extend the statistical treatment to more concentrated solutions, and to examine the magnitude of the errors introduced by assuming that the repulsive interactions are infinite when in fact they must be finite. THE QUASICHEMICAL APPROXIMATION Fortunately, a standard method already exists for taking into account the effect of large interactions upon the entropy of mixing. This is the quasi-chemical method, in which the probability of existence of a given pair of solute atoms in a certain proximate configuration is assumed to be proportional to exp(-w/kT), where w is the energy increase of the solution when the two atoms are moved from isolated locations in the solution to the configuration in question. A quasichemical treatment of interstitial solutions was given in 1937 in a widely neglected paper by Lacher.4 The result comes out

Jan 1, 1963

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By Charles Burrows

THE burden a man can endure depends on its magnitude and the number of tunes it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude f the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary stresses. While we are unable to formulate the law between the magnitude f repeated stresses necessary to produce rupture and the length of time during which these alternating stress may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which, to a first approximation, is exponential. In other words, F = Ce-t where F = magnitude f alternating stresses; = time for which stresses are continued; C = constant, which' depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics f any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 6, 1921

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By R. Bakish, W. D. Robertson

IN the course of a study of stress corrosion cracking of AuCu,, it was necessary to develop new electropolishing and metallographic etching methods. The techniques are generally useful for Cu-Au alloys, including the AuCu composition in which transformation markings are well delineated. For electropolishing, the only satisfactory electrolyte and procedure that has been found1 has the composition given in Table I. The solution must be vigorously stirred while polishing and the temperature maintained in the range of 55" to 62°C. The electrolyte is very unstable and can be used only for 10 to 15 min after which its color changes and a dark-brown precipitate forms. The polishing time is between 1 and 4 min depending on the initial surface preparation. The use of a hood is recommended to avoid the danger of cyanide gas which may form at one of the electrodes even though the solution is alkaline. The optimum current and voltage conditions for vertical anode and platinum cathode are on the plateau shown in Fig. 1, in which voltage is measured across the cell terminals. At voltages below the plateau, etching of grain boundaries occurs and under some conditions, which have not been clearly defined, octahedral etch figures are observed. For general purpose grain-size determination in polycrystalline alloys, a 3 pct solution of iodine in methyl alcohol is used with excellent results. However, when it is necessary to reveal small orientation differences or concentration gradients in an alloy, the iodine etch is not satisfactory. For this purpose, a highly satisfactory etching procedure was developed during this investigation. It involves the use of the vapor given off by freshly prepared aqua regia. The solution employed is 3HC1 to lHNO, which decomposes in accordance with the reaction HNO, + 3HC1 = NOCl + 2H,O + Cl,. The polished specimen surface is held about 1 to 2 cm above an aqua regia solution for 2 to 10 sec depending on the intensity of the contrast required and the surface is not subsequently washed. The results obtained with a coarse grained cast structure are shown in Fig. 2. Subgrain boundaries in a single crystal and concentration gradients within the boundaries are developed by the same treatment with the results shown in Fig. 3. Obviously, any conclusions regarding structure-dependent properties will be modified by the pronounced heterogeneity, which is not clearly evident when more conventional methods are used. Interesting structural details are also revealed by treatment for 4 hr at 850°C in unpurified tank argon. Fig. 4 shows a pattern characteristic of orientation-dependent oxidation.

Jan 1, 1956

By A. R. Matthews

This description of the organization of the Consolidation Coal CO. is intended to include only the portion that is charged with the responsibility of the actual operation of an individual mine, although it has seemed advisable to include several of the all-division personnel, who necessarily come in direct contact with the mine officials. The Consolidation Coal Co. has a staff and line organization and, while most of the contact between these two wings is made between officers ranking above those discussed in this paper, field representatives of several of the staff departments play such an important role in the control of certain phases of activity at the mines that a true picture of the mine organization cannot be had unless these men are included. The demands made upon the producer of large quantities of coal have certainly never been so exacting as they are today. Reductions in the number of accidents and in the cost of individual accidents has passed from the category of a desirable achievement to an unqualified necessity. Although the market price of coal today is lower than it has been in many years, consumers have never been so critical of quality. This market condition is especially severe on the producer to whom one bad shipment may mean the loss of a contract. And the battle to keep the reduction of production costs abreast with constantly dropping prices wages incessantly. For the legitimate producer this situation demands a mine-operating organization that is comprehensive, versatile, efficient and economical; and it is in an attempt to meet these conditions that our present system has been designed. To say that this line-up is incapable of being improved or that it is applicable to all conditions would be to assume a degree of presumption which certainly is not intended here, but our system does meet the conditions which we are called upon to face today with a smoothness and thoroughness which we consider reasonably satisfactory. Authority or Consultation On the chart of Fig. 1 an attempt is made to show as clearly as possible the authority and responsibility of each mine official, together with the

Jan 1, 1931

By Glenn C. Waterman

Richard Strong (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Waterman states (p. 59, Trans., January 1954): "Core-sludge combining factors have been calculaied for any combination of core-sludge recovery on the basis of several logical assumptions: 1—The sludge sample loses reliability geometrically as sludge recovery drops. 2—The sludge sample should not be used if the percentage of sludge return is less than the percentage of core recovered. 3—A core sample should receive a weighting at least equal to the percentage of core recovery." Assumptions 1 and 2 seem justified at Chuquicamata and most geologists would agree to the validity of assumption 3. However, contrary to the statement quoted above, the core sample does not in general receive a weighting at least equal to the percentage of core recovery when the Chuquicamata methgd is used. Furthermore, the basic Chuquicamata method is identical to the Longyear or relative volume core-sludge assay combining method. Finally, the Chuquicamata method does not, in its present form, reflect true geometric loss in sludge sample reliability according to the relationship L = AR (N-1) The basic equations representing the two steps of the Chuquicamata method can be combined algebraically as follows (using the symbology of the original article except as noted): Vol A + B Assay 2 = ASA = Assay 1 Vol A VolB Core Assay [I] Vol A CA.F + ASA (100 —F) Combined grade =[21 100 Pct where F and (100 — F) are the core and adjusted sludge assay factors from Fig. 3. Substituting Eqs. 1 and 2 and collecting terms Combined grade = Vol B Vol A + B CAF (100—-F) + Assay 1 (100-F) Vol A Vol A 100 pct Eq. 3 is a unified and general statement of the Chuquicamata method. The true core factor includes not only the factor F from Fig. 3 but also the quantity VolB ------------- (100 — F), which is implicit in the value of Vol A the adjusted sludge assay. This quantity is real and positive for all values of F and core recovery less than 100. Therefore the true core factor is always less than F except when F is equal to 100. If sludge recovery is 100 pct, Eq. 3 can be further simplified as follows: Let F = percentage of core recovered. Let Vol A = Vdh (100 Pct — Pct CR) where Vdh is the total volume of the sampled interval and let Vol B = (Vdh — Vc.) Pct CR where V, is the core volume in the sampled interval at 100 pct core recovery. Then combined grade = Vo V. CA Pct CR- + Assay 1, 100 Pct — Pct CR Vdh Vdh [4] 100 Pct Eq. 4 shows that when sludge recovery is 100 pct the laboratory sludge assay receives significant weight in the Chuquicamata method, even at 100 pct core recovery. The maximum weight assigned to the laboratory sludge assay depends on drillhole size, as follows: Eq. 4, with suitable changes in symbology, is identical to Royce's formula 8,' which is a statement of the Longyear or relative volume method of combining core and sludge assays. If Mr. Waterman's assumption 3 is of paramount concern to the geologist, the Royce method (for core recoveries of 60 pct and above) or a method employing the percentage of core recovered as a core weighting factor are the only recognized methods known to the writer which achieve the desired result. A modification of the latter method embodying Mr. Waterman's assumptions 1 and 2 would result from applying the factors from Fig. 3 directly to the laboratory core and sludge assays.

Jan 1, 1956

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By Gilbert P. Moore

Bolivia does not yet have any production which is being marketed. It does have a potential production, however, from wells which have been completed by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey. No other company is active in drilling and development work to date. The total potential production from wells now completed is about 6000 bbl, daily. Wells Completed Completions during 1928 and their initial daily productions. if any, were as follows: Camatindi No. 1, 350 to 1000 bbl.: Camiri No. 1, 500 bbl.; Sanandita No. 3, 100 bbl.; Tatarenda No. 1, dry hole, and Bermejo No. 2, deepened 50 ft. made 1000 barrels. The most striking development of the year was the Camiri No. 1 well which, after just entering the sand, made 500 bbl. per day of 52" B. oil. This well is the northernmost good producer which the Standard has brought in to date. Oil from this well is used without refining in the tractors and trucks of the company. A small topping plant has been installed from which high-grade gasoline is obtained for use in motor cars and some is being produced for the use of air plants stationed at Villa Montes. The results for Sanandita No. 13 were somewhat disappointing since Sanandita No. 2 was rated at about 3000 bbl. Tatarenda NO. 1, located on a large unbroken structure, was drilled to 4000 ft. and abandoned as a dry hole. Bermejo No. 2 was deepened 50 ft. to 2085 ft.. and on a 10-day test averaged 1000 bbl. per day. This well is on the border between Bolivia and the Argentine. Wells Drilling The wells drilling are Camiri No. 2, Sanandita No. 5, Machareti No. I and Bermejo No. 5. This is the smallest number of drilling wells which the Standard has had for several years but is principally due to

Jan 1, 1929

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By R. C. McFarlane, T. D. Mueller, J. E. Walstrom

In evaluating uncertainty, experiments are usually performed repeatedly and then conclusions are drawn from the distribution of results. With the advent of high-speed electronic computers, it is possible to perform experiments using mathematical models constructed to simulate complex experiments or operations. Statistical methods are then applied to the results of the simulated experiments. This procedure forms the busis of this paper. Demonstrated is the need for properly accounting for uncertainty in petroleum engineering problems. How uncertainty affects solutions is evaluated in three example illustrations. The method used to evaluate uncertainty in petroleum engineering studies is the Monte Carlo simulation procedure.'-" INTRODUCTION The solution to most technical problems may be derived from interrelationships among several quantities called variables or parameters. There may be only a few variables or several hundred. Interrelationships among parameters may be explicit or implicit, well established or only approximate. Some variables that fully or partially depend on the magnitude of others are called dependent variables. Input variables for most practical problems are not precisely known; there is usually an uncertainty in their value. The degree of uncertainty may vary from one variable to another. Variables that are known accurately are called determinates.' For instance, the gravity of crude obtained from a particular pool may be known precisely, and therefore is a determinate. The degree of precision with which a quantity can be determined increases as data describing the pool are accumulated during the development of the field and the producing life of the pool. The uncertainty of a parameter may result from difficulty in directly and accurately measuring the quantity. This is particularly true of the physical reservoir parameters which, at best, can only be sampled at various points, and which are subject to errors caused by presence of the borehole and borehole fluid or by changes that occur during the transfer of rock and its fluids to laboratory temperature and pressure conditions. Uncertainty may also result in attempting to predict future parameter values. This type of uncertainty is particularly evident in investment analyses involving future costs, prices, sales volumes and product demand. Uncertainty in the solution to investment problems is often called risk, and its study is called risk analysis.' Uncertainty also enters into biological and sociological analyses in which indeterminate factors are often important due to limited control of the experimental material. It is customary, in evaluating uncertainty, to perform repeated experiments and to draw conclusions from the distribution of the results of these experiments. With the advent of the high-speed electronic computer, it is possible to construct mathematical models which simulate complex experiments or operations and to perform the experiments repeatedly, utilizing the models. Statistical methods are then applied to the results of the simulated experiments This method forms the basis of the investigation reported here. PROBABILITY DISTRIBUTIONS FOR VARIABLES The uncertainty in the value of a variable may be indicated by a probabilistic description accomplished by expressing the quantity by a probability distribution. Many recognized probability distributions can be used to describe physical quantities. Recent studies used various types of distributions to describe core analysis data.',' However, for the examples in this paper, the uniform and triangular distributions are believed to reasonably approximate the data used (Fig. 1). The uniform distribution confines the variable between an upper and a lower limit. The variable may lie anywhere between the two limits. This distribution is used when no one range of values for a variable is more probable than any other, but information or intuitive reasoning indicates the variable will lie somewhere between the chosen limits. The triangular distribution is used for a variable when more data are available to indicate a central tendency of distribution. This allows postulating a "most likely" value to the distribution and upper and lower limits. In this case, as for the uniform distribution, the variable is not expected to assume a value less than the lower limit or greater than the upper limit. However, with improved quality of data it can be postulated that the variable will tend to assume a value close to the most likely value, and that there will be a decreasing probability for values away from the most likely value. The area under either of these probability distributions is equal to unity since it is assumed that there is a 100 percent probability that the variable will lie somewhere under the curve. An ordinate erected at any particular value of the variable divides the area under the curve into two parts: the area to the left of the ordinate represents the probability that the value of the variable will be equal to or less than the value of the variable at the position of the ordinate, and vice versa. The probability is zero that the variable will have any specific deterministic value. If two ordinates are drawn for any two values of the variable, the probability that the variables will have a value lying between these ordinates is equal to the area under the curve lying between the ordinates.

By K. Brack, G. H. Schwuttke

Annealing properties of subszerface amorphous lavers produced through high-energy ion implantation in silicon are studied. The buried layers are produced through the implantation of ions (nitrogen), ranging in energy from 1.5 to 2 mev. X-ray interference patterns, transmission electron microscopy, and resistivity profiling are used to study the annealing characteristics of the ion damage. The annealing experiments indicate a low temperature (below 700°C) and a high temperature (above 700°C) region. Significant changes occur in the amorphous layer during the high-temperature anneal. Such changes are corre-lated with the re crystallization of the amorphous silicon and the formation of subsurface (buried) silicon-nitride films. TODAY'S main problems in the field of ion implantation are related to the accurate determination and prediction of 1) the distribution profiles of implanted ions, 2) the lattice sites occupied by the implanted ions, 3) the lattice damage produced through ion implantation, and 4) the annealing characteristics of damage centers in the lattice. This paper reports investigations concerned with the problems listed under 3) and 4). EXPERIMENTAL Our investigations cover the energy range of incident ions from 100 to 300 mev and from 1 to 2.5 mev. The emphasis of this study is on the energy range from 1.5 to 2 mev. The experiments are conducted with single charged nitrogen ions. To implant the ions a van de Graaff generator is used as described by Roosild et al.1 Accordingly, a gas containing the desired ion specie is passed through a thermome-chanical leak into a radio frequency activated source. The positive ions are driven into the van de Graaff with the help of a variable voltage probe. Emerging from the accelerator the ions drift into a magnetic analyzing system and here the desired ion specie is bent 90 deg into the exit port. The ion beam leaving the analyzer is defocused and drifts down a 4-ft long tube to hit the silicon target. At this position the 20 pamp ion beam has a circular cross-section of 2.1 cm. N2 is used as a source gas for nitrogen ions. The implantation target is silicon with zero dislocation density, 2 ohm-cm resistivity, (111) orientation, mechanically-chemically polished, and 1 mm thick. The target is mounted on a water-cooled heat sink and kept at room temperature. A fluence of 1015 to 1016 ions per sq cm is used. RESULTS 1) Silicon Perfection after Bombardment. High-energy ion bombardment of silicon has some striking effects on lattice perfection. Some results were reported in detail previously at the Santa Fe conference2 and are here briefly summarized for the benefit of the experiments described in the following. 1.1) Identification of Surface Films on Silicon. After bombardment all samples are found to be coated with surface films. The films on the silicon surface vary in thickness and color; they can be transparent, slightly brown, or opaque. The films are thicker and darker in the high-intensity area of the beam and they delineate the bombarded surface area of the crystal. The films produce electron diffraction patterns characteristic of carbon and of SiO2. Carbon is predominant. The presence of carbon in these films was confirmed by use of the electron microprobe. Formation of the films occurs independently of the ions used and is attributed to a contaminated vacuum of the high-voltage machine. The carbon is most likely the product of the pump oil which is cracked and polymerized under ion impact. The films stick tenaciously to the silicon surface and burn off in a low-temperature Bunsen flame. 1.2) Mechanical Perfection of the Silicon Surface. The mechanical perfection of the bombarded silicon surface was investigated through optical microscopy, electron microscopy in which the replica technique is used, and optical interferometry. No mechanical damage of the surface was visible after bombardment. However, if a bombarded sample is soaked for several minutes in hydrofluoric acid (HF), gas bubbles may develop in certain spots of the silicon surface. It is also noted that in these areas the surface film starts to peel off. Relatively large patches of film come off if the sample is soaked in HF during ultrasonic agitation. After HF treatment, pits may be present on the silicon surface. The pit dimensions are estimated to be as large as 50 µ. The pits appear in the region of most intense irradiation. 1.3) Lattice Perfection After Bombardment. No lattice damage is found on the silicon surface. Electron transmission micrographs and selected area diffraction patterns of the surface show no difference before and after bombardment. Measured approximately 2 µm down from the surface, the silicon lattice throughout this depth is of good perfection. Well-defined Laue spots and Kikuchi lines are obtained from the surface as well as from the indicated area below the surface. However, some radiation damage is dispersed in this top layer. A sharp boundary line separates this surface layer from a highly damaged layer which extends further downward into the silicon. Typical of this

Jan 1, 1970

By Fred Chappell

Pyrophyllite, a hydrous aluminum silicate, physically similar to talc, receives its name from the Greek word Pyr, for fire and phyllite, a rock or stone. Firestone refers to its first recorded use as firestones or hearthstones. Composition and Properties Pyrophyllite is an aluminum silicate A12O34SiO2H2O (alumina 28.3 pct, silica 66.7 [ ] pct, water 5.0 pct) (Table 1). Vanderbilt1 gives pH value of pyrophyllite as 5.6 to 8.4. Pyrophyllite is usually white or cream, though it may be found in shades of pale green, pale yellow, buff or light gray, and in darker shades and other colors principally due to oxidation of contained iron minerals. It is opaque to translucent in thin sections. Its hardness is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. Its luster is pearly to dull; it is recognized chiefly by its micaceous structure and cleavage, and its soft greasy feel. Two other varieties occur, one in which there are radiated needles in the crystalline form, and there is also a massive homogeneous structure found. Fine grinding reduces pyrophyllite to fiat plates or scales but aggregates of minute foliated plates may be formed.1 Distribution of Deposits Pyrophyllite is found in metamorphic rocks throughout the world but it is only in comparatively recent years that it has assumed much commercial importance. The principal

Jan 1, 1960

By Frank R. Milliken

SCOPE THIS paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, Maclntyre Development, Tahawus, New York. [ ] GENERAL In early 1941, when, world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their Maclntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. Maclntyre Development is at Tahawus, New York, on the headwaters of the Hudson River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. ORE-TYPES From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table 1. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, pyroxene, garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1947

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981

By K. C. Gilbart, E. Stansfield

This test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930,1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 1/4 cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings, and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30" to 35" C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the laboratories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 1/4-in. cubes

Jan 1, 1934

The United States Coast and Geodetic Survey has announced the completion of a new outline map of the United States on the Lambert conformal conic projection, scale 1-5,000,000. This map is intended merely as a base to which may he added any kind of special information desired. The shore line is compiled from the most recent Coast and Geodetic Survey charts, state names and boundaries, principal rivers, capitals, and the largest cities in the different states are also embodied. The value of the new outline map on the Lambert projection can best be realized when it is stated that it shows that throughout the largest and most important part of the United States, that is, between latitudes 30 ½ and 49°, the maximum scale error is only 0.5 per cent. This amount of scale error of 0.5 per cent. is frequently less than the distortion due to the method of printing and to changes from the humidity of the air. Only in southernmost Florida and Texas does this projection attain its maximum error of 233 per cent. The map measures 25 inches by 39 inches and will be sold by the Government at 25 cents.

Jan 7, 1919