Search Documents

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1938

By John Gross

The building of reverberatory furnaces (Fortschaufelungsofen) where ordinary brick, fire-brick and iron are comparatively cheap, is quite a different matter from the building of such furnaces in isolated camps, where proper material is only to be obtained at high cost and with long delays. Time is always a large factor in metallurgical operations, and the metallurgist may find himself in a position where it becomes necessary to erect apparatus and have it running in less time than it would take to obtain material from outside. It is here that he must make use of makeshifts. In Mexico, one of the most important of these is the alluseful adobe. Employed from prehistoric times, it still has its sphere of application in a surprisingly large number of instances requiring an article that can be quickly and cheaply produced. It is quite possible to erect serviceable reverberatory furnaces with no other materials than adobes, stone and wood. The old Mexican smelting shaft-furnace was an example of what can be done with adobes, and the large number of ruins of this class of furnace scattered through the mining districts of Mexico are silent testimony to the genius of a people who demonstrated their capability of adapting material at hand to their needs. The present paper will describe briefly the construction of an adobe reverberatory furnace which is giving good results, can be quickly erected at a low cost, and, if properly built and handled, will last a long time. The material being simply sun-dried, it naturally follows that the construction must be quite heavy. The adobes should be evenly made, with just sufficient straw to hold them together, and not too large in size (9 in. wide, 18 in. long and 4 in. thick

Jan 1, 1902

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes. on, like some writers, talking about ' the former ' and 'the latter ', 'he ', 'she ', 'it), and 'they’, through clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a feeble ending for a serious statement. How often do you hear 'the former' and 'the latter' in conversation? Good conversation is a guide not to be disdained. When you must use 'the latter ', do not confuse it with 'the last '. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is beat. "Partly prevented" is a poor phrase. 'Prevented' is a word that does not lend itself readily to modification. He means ' checked ' or 'corrected '. These steps are necessary to produce the gas, crude oil, and ammonia, the latter [last] of which is in solution in the water obtained along with the oil.

Jan 1, 1931

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By Charles Means

A THOROUGHLY modern coal-handling system has been installed at the Pittsburgh Terminal R. R. & Coal Co.'s new No. 8 shaft, or Coverdale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur f the Montour R. R. The Pittsburgh seam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with their remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. MINE SUBSTATION The transformer substation is adjacent to a pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies.

Jan 9, 1921

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion con- stituting endowments for especial purpose?s. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1937

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In 1947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act.

Jan 1, 1949

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. 'An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1934

By H. L. Monroe

Meramec Mining Co., owned 50% by St. Joseph Lead Co. and 50% by Bethlehem Steel Corp., is engaged in mining, concentrating and pelletizing iron ore from the Pea Ridge Mine which is located about 75 miles southwest of St. Louis. The Pea Ridge orebody lies under some 1300 ft of limestone, dolomite, shale, and sandstone. It runs from east to west for about 1/2 mile and varies in width up to a maximum of around 600 ft. The orebody dips about 80" S. The ore is high grade magnetite with some local zones of specular hematite. The Precambrian country rock is rhyolite porphyry.

Jan 12, 1965

By F. B. Foley

With the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal1 published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-of theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1/14-in (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. with time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the great decrease in breakage by the use of smaller diameter drills. The figures are given as so many drills sharpened, but there is no way of determining the percentage of

Jan 1, 1922

A. M. CANDY,* Pittsburgh, Pa.-I think more stress should be laid upon the question of welding with the carbon electrode, which we ordinarily call graphite arc welding. Mr. Miller's photograph indicated that the original parent metal had been decarburized to a marked degree. It would be interesting to know the carbon content of the parent metal, and whether or not Mr. Miller has made any investigations to determine if the metal is always decarburized or whether in some instances we actually have carbon injected into the weld, which has been the understanding that has been quite prevalent. There were one or two other points that Mr. Miller brought out concerning which I desire to ask one or two questions: The illustrations that he presented were obtained with what, I suppose, would be termed a real low-carbon steel welding wire, which gives in the deposited metal grains that are more or less symmetrical, whereas the Roebling electrode, which is a mild steel of higher carbon content, apparently gives a columnar structure. I do not know which-of these I structures is more desirable, but assuming that the structure produced by the really low-carbon steel wire is the more desirable, would it not be true that the very low carbon content would, probably owing to high temperatures that prevail in the arc, result in a greater amount of oxidation and probably result in either carrying into the weld more oxide or producing more oxide on the surface as the operator progresses? The short arc is an advantage in all cases. Whether Mr. Miller's trouble is oxide or nitride, the short arc helps him out, because the closer the end of the electrode is to the work the less chance there is for either oxygen or nitrogen to get in. And whichever is the cause of the trouble, the short arc keeps it out by lessening the time in which the steel is molten and the amount of air that gets in. It also makes sure that the molten metal will not fall into the crater. Everything is in favor of the short arc.

Jan 4, 1919

By Charles L. Elliot

Data for mining applications of geophysical activity in the Free World in 1963 has been collected by the Committee for Geophysical Activity of the Society of Exploration Geophysicists. This information has been made available to the AIME and is published here in abstract form with the kind permission of the SEG. The data is based or1 244 responses (51%) to the questionnaires circulated among 475 worldwide organizations engaged in mining geophysical operations and or research. It is believed that the data is a realistic appraisal of actual world geophysical activity.

Jan 8, 1964

By F. L. Wolf

THE reclaiming of metallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections, the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby most of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, and table. PRELIMINARY TREATMENT The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five molding floors per day; and the last is collected around the sprue cutters. and knockout bench.

Jan 9, 1920

By U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laist1 says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say ¼ in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly wide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consumption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By Patrick H. O’Neill

FUNDAMENTALLY a dredge designed for operating under arctic conditions and particularly when the temperature is below freezing is not greatly different than one for use in more moderate climates. Because of the accumulation of ice it is necessary to design suspension units to carry an increased weight when ice forms on the digging ladder or stacker. Winch room and house must be made with double walls and insulated. The dredge must be heated either by steam or by circulating warm air electrically heated. The stacker must be covered and heated to avoid having the drive units frozen tight. Actually the worst trouble that might develop in a stacker, because of cold weather, is the freezing of spilled material and ice accumulation on the head pulley and the underside of the belt. For this reason, stackers are completely enclosed and the pan kept open to get rid of any spilled material and to prevent overloading. Since the stacker is the most vulnerable place on a dredge in cold weather, heat is turned on there long before it is necessary any other place on the dredge. The principal points of interest in' connection with dredging, under subfreezing conditions, concern the preparation of the ground being dredged and the frozen ponds. In the interior of Alaska, and also in the Yukon territory of Canada, most of the gold bearing gravel deposits are permanently frozen and they are also covered by variable thicknesses of fine grained sediment, locally called muck. The better pay areas in this frozen ground have generally been worked by the earlier miners who sank shafts to bedrock in the frozen ground, then drifted in four directions and dug out the areas between the drifts as they re- treated toward the shaft. They thawed only the area they were excavating, doing so with steam from wood-fired boilers, and hoisted pay gravel to the surface for subsequent washing.

Jan 11, 1954

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James-Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1934

By Arthur F. Taggart

ENGINEERING education today is like a crazy quilt of somber wools and gaudy shoddy, chain-stitched on an academic assembly line, and sold at ever mounting prices to inexperienced youths for lifetime use. Each engineering school offers a half-dozen or so patterns with essentially the same skimpy wool content. Sales appeal is in the color of the shoddy, denoted by the hopeful adjectives chemical, civil and the like. This article is argument for an all wool product made by slow, careful handwork. Bluntly it proposes a thorough four-year undergraduate drill in fundamental science and general engineering empirics, leavened by continuing study of the third of the engineer's troubles: Man. It is not contended that existing methods of engineering education have failed to start men on the path to successful engineering practice (too many of you have started that way); rather, social conditions and the bounds of knowledge have changed tremendously, and corresponding alterations in the pattern of engineering education are overdue. We'll Teach the Specifics The first part of this contention is illustrated by excerpts from a letter received recently from an officer of one of the largest corporations: "We are interested in employing two or three outstanding young engineers to be placed on a special training program to develop them as design and construction engineers.... "We propose to put these men on a four-month indoctrination and orientation course after which they would be given job-training assignments for a period that will vary from about six months to about a year and a half depending upon the aptitudes, abilities and intelligence of the candidates.... "I am not too fussy about what kind of engineers the men might be insofar as academic courses are concerned. They could be.. . in almost any engineering classification.... We can furnish the additional training beyond the academic fundamentals. "The starting rate for these jobs would be $326 per month...." This letter is not unique; rather it is representative of a practice that has become common. It is industry's enforced response to the general refusal by young graduates to submit to union domination in order to gain operating experience at the labor level. The message to engineering schoolteachers is plain: You teach the fundamentals; we'll teach our practice and pay the graduate to learn it. The letter means to the student that time spent in school studying the specific practices of particular industries is waste compounded. The school can't give the equivalent of what industry teaches, wherefore industry will still demand apprenticeship. The student must pay for the specific instruction at school instead of being paid to take it later. And time-consuming specifics crowd out drill in basic scientific and technical subjects as well as liberal arts.

Jan 1, 1952

By Fun-Den Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stabi1ity.l-3 Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe.3 Rock blocks formed by sets of parallel joints have been analyzed by Wittke.1,2 The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry. A plane of weakness is represented by its dip and strike in vector form and is reduced to the form of a linear equation. The geometry of the rock block is defined by solving the linear equations. The geometric characteristics of a rock block are based on triangles and tetrahedrons. By this treatment, the three-dimensional geometry is simplified and the number of calculations of forces and moments is reduced. Methods of finding the geometric characteristics are presented, along with equations for calculating the resultant forces and moments and the factor of safety. BASIC ASSUMPTIONS The following assumptions are used : The solid part of the rock mass is much stronger than the rock mass at the plane of weakness and the rock mass will only fail along planes of weakness.

Jan 1, 1972