Search Documents

By Forrest F. Craig

Both early and more recent1 laboratory measurements of gas-oil relative permeabilities were made by subjecting oil-saturated cores to external gas drives. In these runs it was generally assumed that the flowing gas/oil ratio was constant at every point throughout the core. Using this assumption, the resulting equation for the gas-oil relative permeability ratio becomes A where Q is the flow rate at the producing end of the system. This relative permeability was then specified for the average saturation of the core. The assumption and resulting equation fail to recognize that in an external drive, the oil flow rate varies from zero at the injection end to a maximum at the producing end. The assumption also fails to consider the existence of a saturation gradient during an external drive. This saturation gradient is due solely to non-steady-state flow. Some authors2,3,4 have used this erroneous method of calculating relative permeability ratios from external drives. Other authors5,6,7 have used relative permeability ratios in calculating expected field performance by external drive, using Equation (1) and making the incorrect assumption that the saturation is uniform within the driven portion of the reservoir. To find the correct relation between the relative permeability. ratio at the average saturation and the produced gas/oil ratio, the insertion in Equation (1) of a factor, F, to adjust it for oil velocity gradient has been considered. The equation then takes the form Assuming that the oil velocity is directly proportional to the distance from the injection point leads to the conclusion that, for a linear system, the average oil velocity is one-half that at the producing end. Thus, the average gas/oil ratio is twice the produced gas/oil ratio, and Equation (2) is transformed into However, here again the existence of a saturation gradient is not recognized. The produced gas/oil ratio is related to the relative permeability ratio at the saturation of the outlet end of the system. It can be shown quite readily that, if the true log k,/k, saturation relationship is linear over small ranges of saturation, then d log kjko Where aaxv and u2 are the average and outlet saturations, respectively. Examination of Equation (3) shows that the factor F cannot have a single value over the whole saturation range. Another method of dealing with external drives is that of Buckley and Leverett.' Their method, which assumes no gas expansion and outlet end effects, considers fully the saturation gradient present due solely to the displacement mechanism during an external drive, and applies Equation (1) to each point along this gradient. The calculation of production history using relative permeability ratio is straightforward. However, the calculation of relative permeability ratios from production history by this method is impractical. In a recent paper, Welge,1 using an approach similar to that of Buckley and Leverett, presents a simplified method for determining the saturation at the producing end of the system. At thi; saturation, the relative permeability ratio calculated by Equation (1) applies exactly, after breakthrough of the stabilizej front. By this method, relative permeability ratios or production history may be calculated with equal ease. Use of this method as a laboratory tool in determination of relative permeability ratios by external drive requires the knowledge of the total injected fluid volume; in addition to the average saturation and producing ratio. As a preliminary test of this method of calculation, laborntory external gas drives were run on a 3% in. diameter, 11 in. long sample of Nellie Bly consolidated sandstone. This core sample had a permeability of 824 md and a porosity of 28.1 per cent. The driving fluid was air. Three different oils were used, having viscosities of 1.4, 9.8, and 125 cp, respectively. The runs were made under identical pressure differentials,

Jan 1, 1952

By M. Van Weyenbergh, G. Van Esbroeck

THE copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment,, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Miniére du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. PRINCE LEOPOLD MINE The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60ºto a depth of 300 ft., and more uniformly 80º below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein-the footwall-is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1939

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

By M. Stuart, R. F. Down

The Copper flotation concentrate produced at Gortdrum mines contains about 1% Hg. This article deals with the treatment used to produce a substantially mercury-free copper concentrate. Metallic mercury is a byproduct. Nearly all the mercury in the Gortdrum concentrate is present in the copper mineral tennantite-tetrahedrite. This mineral is variably distributed throughout the ore body so that by selective mining it was possible to produce salable concentrate relatively low in mercury while the treatment plant was being built. Roasting was the only feasible method found for removing the mercury from the concentrate, and it was decided that this should be done in an atmosphere with limited oxygen. A multiple hearth furnace is used. Mercury soot is condensed from the gas stream and treated to produce prime virgin mercury. Problems were experienced at first with materials handling, oxygen control, cooling of the calcined concentrate, treatment of the mercury soot, and in the metallurgical accounting. Precautions were necessary to avoid health problems. The plant is now operating reasonably well. The value of the mercury produced does not warrant the cost of the plant but without it, the copper concentrate could not be sold.

Jan 1, 1975

By C. S. Trewin

Zinc, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be dctcrmined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent, lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. Rolled Zinc Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. ROLLED ZINC Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

Jan 1, 1928

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By A. E. Dwight, P. A. Beck

A search was made for ordered phases of AB3 composition in various combinations of Ti- and V-group elements with CO-and Ni-group elements. Three new TiNi3-type phases ZrPd3, HfPd3, and HfPt3 were found. In addition, twelve new Cu3Au-type phases TiRh3, Tilr3, ZrRh3, Zrlr3, HfRh3, Hflr3, VRh3, VIr3, CbRh3, Cblr3, TaRh3, and TaIr3 were also found. The lattice contraction for all three structures considered increases with increasing relative size of the A atom, suggesting that it is mostly the A atom that cont~acts. It was noted that, for the same radius ratio the lattice contraction is larger when the A atom is Ti than if it is Cb OY Ta. It is well known that elements or disordered solid solutions, which have structures with spherical close-packing, may be described in terms of various stacking schemes of close-packed layers. Stacking of the type abab corresponds to the hexagonal close-packed structure, and stacking of the type abcabc corresponds to the face-centered-cubic structure. In binary alloys of the first, second, and third long period transition elements various AB3 phases occur with close-packed ordered structures. It was observed that these ordered structures also may be described by suitable stacking of close-packed ordered layers, Fig. 1, as first shown by Laves and Wallbaum for TiNi3.' It is clear that the units of translation in such a close-packed layer consist of four atoms, one of which (black circle) is atom A and the three others (empty circles) are atoms B. Because of the alternation of A and B atoms in every second row of each layer, the unit-cell dimension in the layer is equal to the sum of the diameters of atoms A and B: a0 = 2(rA + rB). Stacking of such layers in the sequence abab results in a hexagonal close-packed structure of the MgCd, type. The unit-cell dimension in the basal plane is approximately double of that for the disordered hexagonal close-packed structure, but in the direction of the hexagonal axis it is about the same, so that 2co/uo = 1.63 in case of spherical close-packing. Ordered hexagonal close-packed structures of this type were found to occur in MoCo3,2 WCo3,, and UPt, .4 When the ordered layers shown in Fig. 1 are stacked according to the scheme abcabc, the resulting ordered structure is of the AuCu, type (cubic). Structures of this type were found to occur in TiPt3,5 CrPt,,' CrIr,,' and URu, .4 Finally, the stacking scheme abacabac of the same ordered layers results in a hexagonal close-packed structure of the TiNi3 type.' In this case, the unit-cell dimension is doubled not only in the basal plane, but also in the direction of the hexagonal axis, so that co/ao = 1.63. Structures of this type were found to occur also in TiPd3,5 ZrPt,," and UPd,.4

Jan 1, 1960

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By R. L. Slobod, H. A. Blum

A semiquantitative method for measuring the wettability of reservoir rocks has been developed. These data are needed for reservoir analysis and for interpretation of laboratory displacement studies. The wettability of a core sample is measured by the contact angle for the system oil-water-solid. These contact angles are calculated from the displacement pressure (threshold pressure) obtained by use of the centrifuge, using first oil-water and second air-oil in the same core sample. This method is based on the assumption that the air-oil and oil-water interfaces occupy similar positions in the porous medium when desaturation of the wetting phase is initiated. The assumption is also made that the Contact angle for the air-oil-solid system which is close to zero in value does not change appreciably even when the contact angle for the oil-water-solid system experiences marked changes. "Apparent contact angles'' for five different solids ranging from 31" to 82" have been determined, and changes irr the "apparent contact angle" of a given sample with laboratory use from 33" to 53' {lave been observed. INTRODUCTION Reservoir rocks vary in their wettability, 1,2,3,4 some being preferentially water wet while other are apparently preferentially oil wet. The degree of wettability, in theory, is measured quantitatively by the contact angle for the system solid-oil-water, hut in 1)practice this quantity is extremely difficult to determine." The need for obtaining some measure of this quantity has become obvious in recent years as a result of both laboratory. and field observations. Several reservoir.: such as the Bradford Sand in Pennsylvania and the Wilcox' at Oklahoma City are reported to be oil wet. If these report:: correctly reflect the true nature of the surface of the rock in the ground, then these reservoirs probably will not perform as predicted on the basis of a water wet rock. In the laboratory many core samples have been Observed to be oil wet. These samples, while perhaps not correctly representing the reservoir, have markedly different properties from water wet rock. The location of the phases is different (oil is in contact with rock instead of water), and other quantities such as the connate water, the capillary pressure curve; residual oil. relative permeabilities. and the recovery of oil by water flooding are markedly affected by the value of the contact -4 A further complication observed in the laboratory is the chang-ing of the wettability of a rock specimen with use. such changes mean that repeat runs on the same core are not the duplicate tests desired, but represent new experiments on a more oil wet material. The changes in surface characteristics are sometimes so rapid that by the time an experiment requiring several days is completed, the results may not be representative of the core as originally described, The, rock material itself (Silica. carbonates. etc.), whell Clean and uncontaminated, is water wet. There seems b( : little evidence of the presence of oil wet minerals such as heavy metal sulfides. The oil wetness of reservoir samples, therefore, is believed to be caused by the accumulation of an adsorbed film in which the polar group of a large organic. molecule is adsorbed on the surface leaving the organic or hydrocarbon part of the molecule projecting out from the solid. Such a surface is much more readily wet 17" oil than by water. These considerations indicate the need for a method which will provide some measure of tile wettalbility (Contact(angle if possible) for reservoir rock ..samples) The method should be capable of (1.1 distinguishing between tile wettalility of dif. ferent formation,.. (2) detecting (change. ill wettalbility of a core with use. and (3) measuring the changes in Wettability which may be accomplished with cleaning operations. such as the use of sodium silicate for increasing water wrettalbility." A preliminary report on such a method is preseted below. not with the idea that this procedure alone will Solve the wettabil-ity problem. but rather that it may provide encouragement to

Jan 1, 1952

By Torgrim Eftestoel, Leif Olsen, Ove Sandberg

IN the vertical contact Soederberg electrode for aluminum furnaces more or less serious cracks are sometimes formed in the electrode, with harmful effect on furnace operation. The problem of crack formation has been studied on a laboratory scale to obtain a better understanding of this phenomenon. The primary cause of crack formation is the shrinkage of the electrode carbon, which is opposed by the normal thermal expansion of the steel contact studs. The forces thus set up are active in the temperature interval from which the electrode obtains a rigid structure (450" to 500°C) to furnace operational temperature (950°C). A visualization of our reasoning is given in Fig. 1, which shows the different behavior of mild steel and electrode carbon during baking. Research work performed to determine relationships between crack formation and shrinkage will be described. A brief description of the method developed for measurement of shrinkage will be given, as well as a critical analysis of this method. Also, raw material quality and paste composition variables will be related to shrinkage phenomena. Laboratory Test of Crack. Formation To test the tendency toward crack formations of Soederberg electrodes from different pastes, experiments were performed to simulate conditions of actual commercial electrodes, and are described as follows. A cylindrical test electrode is prepared by tamping the electrode paste to be examined in a sheet iron casing, 350 mm diam by 700 mm height. The casing is perforated, with the holes (2 mm diam) 50 mm apart, to facilitate the escape of volatile matter during baking. A cylindrical steel stud of actual service size, 100 mm diam, is welded eccentrically to the bottom steel plate, and protrudes up through the paste. During baking, a crack may thus occur in the weaker part of the test electrode. The electrode is baked by lowering the assembly slowly into an electric furnace, the temperature of which is kept constant at 900°C. After baking of the electrode, the sheet iron casing is removed and the electrode inspected for cracks. The pictures in Fig. 2 are of three different pastes baked according to the present method. Electrode 1 has a large crack; electrode 2, a somewhat smaller one; and electrode 3, only a minor crack. As will be seen from the simplified sieve analysis diagram of Fig. 2, the compositions of the pastes in question are very different. This subject will be discussed later in greater detail. Crack Formation and Shrinkage Relationships It is well known that shrinkage occurs in coke in the higher temperature ranges of coal

Jan 1, 1958

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the dose association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and' 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill 10,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. 1) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1017 and it was operated during parts of 1918 and 1910. In the postwar years, there was almost no demand for the product and production was at a standstill until 1024. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By H. B. Charmbury, D. R. Mitchell

Recovery of fine coal from solids reporting to wash water has become increasingly important. These solids range from about 28 mesh to 0 and constitute 3 to 7 pct by weight of the feed tonnage to a coal preparation plant. In the past they were usually wasted to streams, but present clean stream legislation makes it necessary to remove them from the wash water and, if economically possible, recover the associated coal as a saleable product. Where these solids are not wasted to streams or to slime ponds they are recovered by thickeners and filters. Since filter cake is often high in ash or sulfur, or both, it is not readily marketed or used. Common practice is to mix it with other plant products, generally slack or cleaned run-of-mine. Uniform blending is difficult, not only because the impurity is usually high, but also because during certain operating periods it is possible to get a concentration of this filter cake in a railroad or barge.

Jan 2, 1959

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By J. W. Bolton, S. A. Weigand

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

MODERN mining is based on drilling--everything else stems from that. U. S. and Canadian mining companies and suppliers of mining equipment are constantly seeking new techniques and tools for increased drilling efficiency. Ultimate goal is increased bit-against-rock time. Just how important their efforts are can be seen through a legitimate extension of available statistics. In Canada some 70 million ft of drilling per year is required. While the number of feet actually drilled in the U. S. is unknown, it is possible to compare U. S. and Canadian mineral production, excluding oil and coal. In the U. S. mineral value was $4200 million and across the border $836 million. Taking into account the number of drilled feet required to produce Canada's total, the U. S. total would be 365 million ft in 1953. A saving of 14 per ft would reduce over- all metal and nonmetal mining costs some $3.65 million per year. This does not take into account other indirect savings. Methods have changed and there have been structural and metallurgical advances in blasthole practice in the last ten years. The Editors of MINING ENGINEERING in the articles on the following pages present the most significant innovations coupled with results in the field. Environment plays an important role in selection of materials and equipment -but while unanimity does not exist throughout the industry in reference to drilling problems, a definite trend is evident. For the story of that trend read the articles on the following pages.

Jan 9, 1954

By H. M. Chance, T. M. Chance

The term 'Llow-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as.1 1/2 per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. , In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low-sul. fur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, with few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 1/2 per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous districts, it has been necessary to turn to the areas of higher sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.—Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout the coal but is usually confined to high-sulfur benches in the bed or to concentrations on the cleavage planes of the coal. Hence, by graded crushing and sizing it is frequently possible to at once reclaim those portions of the coal bed containing coal that is relatively free from pyrite.

Jan 1, 1920

By H. D. Yoo, M. R. Tek, D. L. Katz

The behavior of gas-storage reservoirs subject to water drive is investigated through analog simulation on an electronic differential analyzer. The simulation technique developed on an LM-10 computer permits the prediction of reservoir volume or pressure resulting from the movement of water in the surrounding aquifer. The method developed on the analog computer consists of setting up an appropriate transfer-function circuit and feeding the arbitrary time-varying boundary conditions as an input signal. The input may be specified as gas reservoir pressure, pore volume or the water flux. Several cases studied include an isolated gas reservoir on a limited aquifer, interference among three reservoirs adjacent to a common aquifer and the growth of gas-storage volume on an aquifer. It is concluded that the method developed on an electronic differential analyzer provides an excellent technique to simulate and investigate the behavior of gas reservoirs subject to water drive. The agreement between the reservoir performance as predicted from the simulation technique and as measured from actual field data is found to be better than the range usually encountered in predicting water-drive behavior. INTRODUCTION It is generally known that some gas-storage reservoirs are located on top of blanket sands of large extent, saturated with brine called aquifers. Because the volume of the body of water associated with aquifers is usually very large and water is compressible, the cyclic pressure variations encountered in normal storage service inevitably cause unsteady, compressible flow conditions in the adjacent aquifers. The solution to radial diffusivity equation for a limited aquifer for constant terminal conditions has been know111 since the early 1930's. The solution for the constant terminal conditions for an infinite aquifer was puhlished in 1949.2 The proldem of handling the unsteady flow of water through a porous medium with time-varying boundary conditions has been studied by many investigators through the use of graphical,3 digital4 computing techniques or on an R-C type of electrical analog called a reservoir analyzer.5 The digital computer performs a series of arithmetic calculations to superimpose the solutions of constant terminal conditions, while the R-C type of analyzer permits the simulation of the continuous medium by means of "lumped-cell" electrical resistance and capacitance elements based on finite-difference approximations. The graphical method is based on the convolution integral solution of the partial differential equalion. The purpose of the present study was to simulate the behavior of an aquifer on a general-purpose, electronic differential analyzer to obtain the influx of water or the change in pressure at the reservoir continuous1r and quickly. The use of the electronic differential analyzer was based on well known solutions for the constant terminal conditions already available in the literature.2,6-8 THEORETICAL DEVELOPMENT MODEL. The gas reservoir (R) is described in relation to an aquifer in Fig. 1. The permeability and porosity of an aquifer sand, the viscosity of the brine, and the compressibility of the brine and the formation are assumed to be constant. It further is assumed that the blanket sand is not thick enough to give appreciable vertical pressure distribution. The model in consideration is circular with radial geometry. The aquifer radius can be of limited or infinite extent. The gas-water interface is assumed to be fully segregated, and the displacement of the gas by