Search Documents

By Robert D. Coale, Reinhart P. Ehrlich, Terry L. Thompson

The copper concentrate slurry pipeline and pumping system of the Bougainville Copper Ltd. facilities on Bougainville Island in Papua New Guinea, is discussed. Development work necessary for the pipeline design is dealt with including a description of the 17-mile by 6-in. pipeline and pumping system as it was installed. The commissioning of the pipeline is reviewed as well as current operating performance, including data on corrosion, pump parts life, and manpower requirements.

Jan 1, 1977

By B. M. Bird

DURING the past four years the experimental work in coal washing carried on by the U. S. Bureau of Mines and the University of Washington has been devoted mainly to the development of special methods for the tabling of fine sizes of coals that are difficult to wash. One important outgrowth of this investigation has been the application of hindered-settling classification to coal tabling. Although used for many years in ore dressing, the term "classification" as used here may be new to many readers. It may be defined as the separation obtained when a bed of particles is held in a uniform state of suspension in an upward current of water, either continuous or pulsating, just sufficiently strong to keep the bed in a mobile condition. A common example of this type of separation is a jig in which there is no suction stroke. When the hindered-settling classifier is used with the coal-washing table, the fine-size raw coal, instead of being fed direct to tables, as is the prevailing practice, is first fed to the classifier and grouped, according to the rate of settling against the upward current of water, into perhaps six separate products. After dewatering, each of these except the sixth, a refuse product, is elevated to a seperate feed bin and washed on a separate table. This paper gives a brief discussion of the basis for the use of hindered-settling classification of a table feed; a description of the experimental work; a comparison of the results obtained with and without classification; and a discussion of the application of the classifier in commercial coal washing.

Jan 1, 1928

By Maurice Ewing, L. Don Leet

The most important quantitative method in seismic prospecting by refraction shooting is the method of profiles. A profile is established by firing a series of charges at various points along a straight line which terminates at the seismograph. The same data are obtained by repeatedly firing charges at one place and recording at a series of stations along the line of the profile. The quantities which are measured are the distance x from each firing position to the seismograph and the time t required for the first disturbance from each explosion to travel to the seismograph. These data are used in plotting the familiar time-distance graph. The only time-distance graphs that will be considered here are those obtained in localities where the velocity of propagation depends solely on the depth beneath the surface; that is, where there is no slope in the subsurface. The essential calculation to be made from such a time-distance graph is the determination of P(x), the maximum depth of penetration of a disturbance coming to the seismograph from a firing point at the distance x from the instrument. If the time-distance graph consists of a series of straight lines, as is often the case, the penetration P(x) can be calculated by means of formulas which appear in almost every description of seismic prospecting.' Until the present, however, the only formula that has been available for calculating P(x) for time-distance graphs which are smooth curves is one which requires an arbitrary assumption regarding the law of velocity increase with depth.2 The practice in these cases has been to approximate the curve by means of a number of straight lines and then to apply the ordinary straight-line formulas. This method clearly can yield accurate results only when a sufficiently large number of straight lines is used. The labor of computation increases rapidly when the number of lines is increased, so too few lines often are used. Further than that, there is a strong tendency to overlook the approximate nature

Jan 1, 1932

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS as to the methods of smelting ores and of obtaining metals I discussed in Book IX. Following this, I should explain in what manner the precious metals are parted from the base metals, or on the other hand the base metals from the precious'. Frequently two metals, occasionally more than two, are melted out of one ore, because in nature generally there is some amount of gold in silver and in copper, and some silver in gold, copper, lead, and iron ; likewise some copper in gold, silver, lead, id iron, and some lead in silver ; and lastly, some iron in copper2. But I will begin with gold. Gold is parted from silver, or likewise the latter from the former, whether it be mixed by nature or by art, by means of aqua valens3, and by powders which consist of almost the same things as this aqua. In order to preserve the sequence, I will first speak of the ingredients of which this aqua is made, then of the method of making it, then of the manner in which gold is parted from silver or silver from gold. Almost all these ingredients contain vitriol or alum, which, by themselves, but much more when joined with saltpetre, are powerful to part silver from gold. As to the other things that are added to them, they cannot individually by their own strength and nature separate those metals, but joined they are very powerful. Since there are many combinations, I will set out a few. In the first, the use of which is common and general, there is one libra of vitriol and as much salt, added to a third of a libra of spring water. The second contains two librae of vitriol, one of salt-petre, and as much spring or river water by weight as will pass away whilst the vitriol is being reduced to powder by the fire. The third consists of four librae of vitriol, two and a half librae of saltpetre, half a libra of alum, and one and a half librae of spring water. The fourth consists of two librae of vitriol, as many librae of saltpetre, one quarter of a libra of alum, and three-quarters of a Mbra of spring water. The fifth is composed of one libra of saltpetre,

Jan 1, 1950

By Joseph Hodgson

Introduction SINCE about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develope the different phases of various mining subjects at regular meetings.

Jan 5, 1916

This report presents the comments of members of the Institute's Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of occasional use by the Indians. However, the first recorded discovery of coal, in what is now the US, was by French explorers, who reported an outcrop exposure on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coalfield near Richmond, VA, a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New York, and Boston. During the Revolution this coal was of importance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1981

By W. G. Scott

Since devising the incline top-slicing method in use at the Coronado mine,l I have had numerous inquiries as to how the same system could be adapted to larger orebodies. Based upon our experience here, I have outlined below some suggestions for its application to orebodies of larger size. Modifications and extensions, of course, would have to be made to take care of different dimensions and irregularities. In order that one may have a better understanding of the scheme, a brief description of the Coronado method will be given first. CORONADO METHOD The portion of the Coronado vein that is worked by the slicing system ranges from 20 to 40 ft. (6 to 12 m.) in width. Preparatory work in this orebody consists of driving sub-levels every 55 ft. (1 6.77 m.) vertically, or in multiples of 11 ft. (3.36 m.) (which is the height of a slice). These levels are usually driven along the hanging wall until the end of the orebody is reached. Crosscuts, at right angles to the strike, 50 ft. (15.24 m.) apart, are then run from wall to wall, or until the lean ore is reached. They are run in the middle of the block, which is 50 ft. in length and the width of the vein. The crosscut on the hanging-wall side is extended in the wall a short distance for a manway and timberway raise. This raise is carried up in the wall to the sub-level above, leaving a pillar about 5 ft. in thickness between it and the vein. Connections are made every 11

Jan 1, 1918

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By D. S. Choi, D. L. McCain

A method of estimating the chain pillar size required to support the wide working faces of longwall or shortwall coal mining is presented. The pillar size is determined through the use of coal strength, entry geometry, panel width, and overburden pressure. Design analysis is focused on a three-entry development system in the Pittsburgh Seam but can be used for other development plans and other seams by substitution of the proper geometric and strength data.

Jan 1, 1981

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By J. M. W. Mackenzie, C. J. Wood

In attempting to describe the size classification performance of a hydrocyclone, most workers have elected to use either an equilibrium orbit theory or an non-equilibrium orbit theory. The equilibrium orbit theory has been used by the majority of workers including Lilge,' Bradley; and Yoshioka and Hotta. In applying this theory, it is argued that particles in the body of a hydrocyclone attain an equilibrium radial position where the drag force on the particle resulting from the inward radial fluid velocity is balanced by the outward centrifugal force caused by the tangential component of fluid flow. When considered over the full height of the hydrocy-clone, attainment of this radial equilibrium orbit results in the particle following a conical equilibrium envelope. It is then argued that if this envelope lies outside the envelope of "zero vertical velocity," the particle will report to the underflow, while if the equilibrium envelope lies inside the envelope of "zero vertical velocity," the particle will report to the overflow or vortex finder product. The d50-sized particle which reports in equal quantities to the underflow and overflow is assumed to correspond to particles whose equilibrium envelope is coincident with the envelope of "zero vertical velocity." In considering the equilibrium orbit theory, it is apparent that the horizontal position of the particles in the feed inlet pipe should have no effect on their ultimate destination on the hydrocyclone. Each particle should attain an equilibrium position which depends on the density, size, and shape of the particle; the density and viscosity of the fluid; and the flow patterns within the hydrocy-clone. The nonequilibrium orbit or unsteady state theory has been largely developed by Rietema4 and Mizrahi.6 Mizrahi has listed four main objections to the equilibrium orbit theory. These objections center on the short residence time in the hydrocyclone, the fact that the experimental classification curve is much less sharp than is theoretically predicted, and the absence of negative efficiency conditions in hydro cyclones operating on a feed material which is much finer in size than d50. Proponents of the nonequilibrium orbit theory argue that for a particle to discharge with the underflow it must have sufficient outward radial velocity to reach the downward-flowing region close to the hydrocyclone wall in which the flow lines are parallel to the wall and the ratio of vertical to radial velocity is constant. It is then postulated that a d50 particle entering the cyclone at the center of the feed inlet will just reach this downward-flowing region as it reaches the apex. Thus for uniform distribution of particles across the feed inlet, half the d50 particles—that is, those injected in the half of the inlet area nearest the cyclone wall —will report to the underflow while those injected in the other half will not reach the downward-flowing region and will be carried inward to the center of the cyclone and thus report in the overflow. The exact thickness of the down-ward-flowing region of fluid adjacent to the outer wall of the hydrocyclone is uncertain but Mizrahi considers it to be equal to the apex radius minus the air core radius. Particles larger than d50 have a greater outward centrifugal force acting on them than the d50 particles and may reach the wall even if injected at a distance from the wall greater than Di/2 (Di is inlet diameter). Conversely, particles smaller than d50 may not reach the wall even if injected at a distance less than Di/2 from the cyclone wall. Since the equations put forward by the proponents of both theories yield approximately the same values of d50, it is not possible to decide between these theories by measurement of d50. It should be possible however to examine the theories by injecting a small stream of solids into the feed inlet of a hydrocyclone running on clear water. If the efficiency or classification curve is measured for various horizontal injection positions, then the curves should be coincident if the equilibrium orbit theory holds. If, however, the unsteady state theory describes the cyclone operation, then the classification curves should show finer d50 sizes for particles injected close to the cyclone wall. Experimental A 6-in.-diam hydrocyclone with geometry as in Figs. 1 and 2 was used. Quartz particles were injected as a 50% by wt pulp via an 1/8-in. steel probe. For each in-

Jan 1, 1971

By D. C. Shelton, C. S. Ek

Corneille S. Ek (Assistant Professor in Ore Dressing, University of Liege, Liege, Belgium) — This is a very valuable paper, in that it shows how it is possible to take care of a multitude of laboratory routine tests, and derive from them successful modifications of flowsheets or of operating methods. The author and the Company appear to be test-minded and this is best seen through the case histories described. There are however some corrections to be made, and questions arise when one studies the paper. If all the equations are to be homogenous, one obviously has to write Eq. 4 On the other hand, it is difficult to accept the definition put on Eq. 7, for that equation, which represents the factor of transformation from tpd of solids to cu ft per min of pulp in Eq. 6, has nothing to do with conditioning. It is evidently assumed here that conditioning means, as Gaudin calls it,' modulation of collection. One would prefer, for Eq. 7, the appel-ation "pulp conversion factor". Eq. 8 and 9, giving the amount of reagent to be fed

Jan 1, 1965

By Donald W. Scott, L. A. Roe, B. J. Sweo

INTRODUCTION THIS paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizers and organic dyes, and 35 parts of water are added to loo parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder' in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the overspray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1947

By Amos P. Brown

PYRITE, the bisulphide of iron, FeS2, is found more or less in all coal-beds: but, as a rule, in certain definite forms. More than any other impurity, it detracts from the commercial value of a coal-deposit, and yet its presence is so universal that it might almost be said that there is no coal entirely free from pyrite. My observation has been confined to the Pennsylvania bituminous and semi-bituminous coals, and to them, therefore, my remarks will be confined. Certain generalizations which I may make, however, will be found of universsl application. The lowest members of the coal-formation, No. XIII. of the Pennsylvania bituminous region, are nearly always pyritiferous, and in many cases highly so. In Cambria county, for instance, coalbed A, the Brookville, is locally known as the " Sulphur seam." The Lower Kittanning, in parts of Clearfield county, is so sulphury as to be almost unmarketable, though otherwise it is a strong locomohive coal. In Mercer county the Pardoe bed, so extensively mined there, carries great quantities of sulphur in the form of pyrite, though usually this can be separated in such a way as to detract little from the market-value of the coal. The other coal-beds of the Lower

Jan 1, 1888

By Marvin P. Barnes

Definition The term mineral inventory is a relatively new designation, born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral Inventory makes no presumptions about the minability of the blocks or their cutoff grade. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral Inventory is an excellent designation for describing mineral value distributron within a deposit's geological setting

Jan 1, 1979

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956

By H. H. Stoek

THE fundamental reasons underlying the choice of a method of mining a coal seam are safety of operation, cheapness of producing the product and the character of the product as a saleable article. From the standpoint of safety, open or strip coal mining is always preferable, as many of the dangers inherent to underground work are absent, such as explosions of gas and dust, falls of roof and coal, and also to a great extent those due to haulage and the use of explosives, thus eliminating three of the chief causes of accident from which about 75 per cent. of the underground accidents in coal mines occur. The conditions under which coal is stripped also make the work much safer than ordinary quarry work, as the depth. of the pit is usually comparatively slight. From the standpoint of low mining cost, there is much misapprehension and many of the costs given are misleading in that they do not take into account such items as the destruction of the surface for future use, the full cost of the removal of the overburden, depreciation, amortization, coal depletion, loss of time through floods and from bad weather in winter, etc. Coal is no doubt often put on the cars at less cost by stripping than by underground mining, but by no means always so, as is too generally assumed. In some cases coal must be obtained by stripping or not at all, due to the small amount of overburden that renders underground mining impossible.

Jan 9, 1917

By David Cornell

Back pressure test data on natural gas wells are short time test data of unsteady state nature. Performance curves from which unsteady state effects have been eliminated, called stabilized performance curves, are necessary for understanding the behavior of gas wells and for scheduling gas fields for periods up to 20 years. A calculation procedure has been developed whereby three day, seven day, 30 day, or other duration stabilized performance curves may be calculated from back pressure test data. Such curves are essential for correct gas deliverability calculations and gas field scheduling. I NTRODUCTION The manner in which a back pressure test is made will affect the slope of the back pressure curve because the radius of drainage changes with the length of time that the well is allowed to flow. The reciprocal of the slope of the back pressure curve is defined as n in Equation 1 and varies from 0.5 to 1.0. If the flow is viscous and the radius of drainage constant, n will have a value of 1.0. Because of turbulence in the formation near the wellbore, the pressure drop is usually greater than the viscous flow pressure drop and the exponent n is frequently less than 1.0. In addition, since the radius of drainage moves away from the well-bore during the test, the gas flows a greater and greater distance as the test proceeds, with a resulting increased pressure drop at the high flow rates, and, again, n for the test tends to be less than 1.O. The effect of the changes in the radius of drainage may be calculated and the results used in preparing stabilized performance curves for fixed values of the radius of drainage. Such curves can be made for a defi- nite time period, such as three day, seven day, or 30 day stabilized performance curves. These cukes will show the effect of turbulence near the wellbore and can be used to predict the performance of the gas well at any flow rate or for any production period. In order to discuss the importance of the radius of drainage quantitatively, it should be defined. Muskat" defines the radius of drainage as follows: "... the radius of drainage gives the distance from the well to which the approximately steady state condition has been established ... it being assumed that no gas is removed from any point until the radius of drainage has passed that uoint." An eauivalent definition of the radius of drainage is that radius at which the extrapolated portion of the steady state portion of the pressure gradient gives a pressure equal to the shut-in reservoir pressure. This definition is also implied in the back pressure equation. The radius of drainage is, then, the distance into the reservoir from which the gas appears to originate at any time. It is, however, only a useful concept and does not actually exist. Fig. 1 illustrates the definition of the radius of drainage. At the end of each flow period the radius of drainage may depend on three factors: (1) the duration of each flow period; (2) the rate of gas production; and (3) the rate and duration of the previous flow periods. In general, back pressure tests are conducted with various lengths of production time and at various flow rates. Each individual back pressure test, therefore, requires an individual analysis. The calculations of the change in the radius of drainage have been made, however, for the case of equal flow periods for all four production rates and several sets of increasing flow rates. Fig. 2 illustrates the results of such calculations made by the method of Cornell and Katz2 for the case of 8, = 50,000 and the flow rate increasing in the ratio 1.0:2.0:3.0:4.0 for each flow period. The increase in the radius of drainage during the test is apparent.

Jan 1, 1956