Search Documents

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C'. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h'b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,' by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K' is the value for the Fe-S binary solution. and the limiting value of K' in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1' that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By Neil Styler

This paper presents an analysis of measurements of inter-burden deformations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock extending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By R. E. Ford, P. Tarassoff, P. H. Jennings

Copper oxide ore may be leached at all sizes from run-of-mine down to pulp, and consideration must be given to all available methods in determining the most economical one. Heap leaching was evaluated in a pilot plant at Gaspe Copper Mines, Ltd. which was designed to simultaneously leach two 1200-ton dumps of ore. The plant was operated for two years, in part under severe winter conditions. Two modes of leaching were investigated: acid leaching in which sulfuric acid was added externally to the leach solution, and pyritic leaching in which pyrite concentrate was added to the dump and acid was generated in situ by bacterial action. The pilot plant operation is described, and the results are compared with laboratory data obtained in 6-in.-diam columns. It is concluded that pyritic leaching offers certain operating advantages over acid leaching when copper is recovered by cementation in that iron buildup in the solution is prevented.

Jan 1, 1974

Anticipating the increasing importance of establishing working conditions on a scientific basis, the Department of Labor created the Working Conditions Service. This service is distinct from that performed by the Mediation and Conciliation branch, which deals with working conditions and industrial relations as controversial issues between employers and employees. The work of the Service is conducted through three coordinated divisions; Division of Industrial Hygiene and Medicine, Division of Labor Administration, and Division of Safety Engineering. The Division of Industrial Hygiene and Medicine will develop standards of sanitation and medical practice in industries. The personnel of this Division is detailed from the United States Public Health Service. The Division of Labor Administration will advise employers as to employment systems and labor management policies, and assist in putting into operation standard policies.

Jan 2, 1919

By R. T. Hukki

BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that [ ] Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate).

Jan 6, 1954

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By E. H. Dix, F. Keller

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By F. Keller, E. H. Dix

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By E. P. Bucklen

Simulation is a tool useful in the evaluation of the probable effect which various changes may have on the performance of time-dependent systems. This is especially true as far as rail transportation in mining is concerned. The VPI-OCR RAILSIM program is a computer program designed specifically for solving a broad range of problems encountered in the design of haulage systems of new mines as well as in the operation of haulage systems in existing mines. This program is one of several computer applications for evaluating mining systems developed at the Virginia Polytechnic Institute and State University under contract with the Office o f Coal Research of the U.S. Dept. of the Interior. The RAILSIM program uses Monte Carlo techniques to introduce variability in the occurrence of events such as would be observed in real systems. Data are required to describe the haulage network, locomotives, stationary facilities, and other miscellaneous parameters. Output from the program lists measures of performance that are useful in assessing the capabilities and limitations of given system configurations. The output information may cover many shifts of operation to indicate the broad range of variation and interaction which can occur as the system responds to varying levels of demand for service. The RAILSIM program was tested extensively in mining operations. The results of some of these tests are used to illustrate the usefulness of this program.

Jan 1, 1972

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

The annual spring excursion of the College of Mines, University of Washington, is being made to the Coeur d?Alene region of northern Idaho. A party of 15 students and, instructors is visiting the Bunker Hill and Sullivan mine, mill and smelter at Kellogg, and several mines and mills in the neighborhood of Wallace and Mullan.

Jan 5, 1917

As a service to its readers, MINING ENGINEERING is publishing the mineral industry portion of the 1957 list of Accredited Undergraduate Engineering Curricula in the United States. This list, revised annually, is issued by the Education Committee of the Engineers Council for Professional Development, and covers all phases of engineering education. The AIME is actively represented on ECPD, which was jointly organized by the Founder Societies and various other groups interested in the professional recognition of engineers. ECPD is merely authorized by its constituent organizations to publish a list of accredited engineering curricula for use as desired by those agencies which require such a list. It has no authority to impose any restrictions or standardizations on schools. (Date following school refers to year of initial accrediting.)

Jan 7, 1958

By H. W. Morse

MANY of our largest copper deposits contain both sulfide and oxidized copper minerals. The large porphyry mines, with a total copper content of from 1.3 to 2.0 per cent., send to their mills ore with an oxide content of from 0.2 to 0.4 per cent. While the recoveries of the sulfide minerals are considered satisfactory, using modern flotation practice, the recovery of the oxi- dized portion of the copper is small; better recoveries of oxidized copper were made before flotation methods were adopted. Beside the ores containing copper mainly as sulfide, with a small amount of oxidized copper,, many of the large porphyry mines have oxide orebodies, in which the propor-tion of non-sulfide minerals is so high that 2 present methods of treatment are ineffi-cient. In some of the well-known ore-bodies in the Miami-Inspiration district the copper occurs about equally in sulfide and oxidized forms; and the mixing of minerals is complete throughout the ore-body. There is no possibility of mining the sulfides and the oxides selectively. At the New Cornelia mine, however, the oxide, and sulfide ores are sharply separated, per-haps by an ancient water level, so that the oxide ore may be mined and treated in a plant built for that purpose, and the under-lying sulfide ore may be left for treatment in another plant. If copper is to be made from an ore having a total content of 1.5 per cent., it must be concentrated or removed from the ore by some. hydrometallurgical method. Flotation is generally successful for the sulfide minerals and flotation after filming with sulfide seems to work in many cases on the pure carbonate minerals. Callow has given an extensive report on the results of "sulfidizing" flotation on the ores of the. Magma mine.1 Where such ?a &apos;method can be applied, it ?may be, the best

Jan 9, 1922

By Dewitt T. Ring

Oil development in 1934 has been largely restricted to drilling offset and lease requirement wells. Practically no effort has been made to discover new fields, chiefly because of price structure and proration allowance. A summary of developments during 1934 of necessity is brief. No state agency is maintained for the collection of data. The State Bureau of Mines issues permits for drilling and inspects the plugging of wells in coal-bearing measures only. Therefore data are not in existence with which to compile tables similar to those in other papers of this symposium. Forty-seven counties in the state produce oil, productive depths ranging from 100 to 5300 ft. Approximately 35 different formations in Ohio have produced either oil or gas. These reservoir rocks occur through a stratigraphic interval ranging in age from the shallow Goose Run sand of the Upper Pennsylvanian in Washington County to the St. Peter sand of Lower Ordovician in Seneca County. However, 75 per cent of these formations are unimportant from the standpoint of real production. Most of the oil and gas in Ohio has been produced from the Clinton, Oriskany, Berea and Big Injun sands and the Trenton Lime. Of these, the Clinton is first and Berea second in importance. Fields The oil and gas-producing territory of the state can be grouped into five fields or districts, made up of a series of "pools" usually separated by nonproductive areas, and is in no sense a belt of continuous production. Trenton Field of northwestern Ohio, is scattered through 15 counties. Development began in 1885. This field reached its peak in 1896 with a production of 20,575,138 bbl. for the year. For 1934, production had declined to 990,000 bbl. The oil is classified as Lima grade. Clinton Field extends from the Ohio River in Lawrence County to Lake Erie in Lorain, Cuyahoga and Ashtabula counties. First Clinton-

Jan 1, 1935

By Howard E. Kremers

Since the discovery of the first-known rare earth elements more than a century ago, these metals have always been of academic interest. It is not so well known, however, that a rather stable, respectably large industry based on rare earths and their related materials has been in operation for more than 60 years. Rare earths, of course, are the elements having atomic numbers 57 through 71--lanthanum through lutetium in the periodic table. The most important commercial members of this group are mixtures of the lower atomic-numbered rare earths, and cerium. Although yttrium is not a rare earth, it occurs with rare earths and its properties are so similar to them that. it must be included in a discussion of these elements. In addition, thorium is important to most producers of rare earths because their ores generally contain this element. Thorium extractive metallurgy and technology is closely related to rare earth chemistry due to the frequent similarity of properties.

Jan 4, 1962

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently pub lished by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so de sirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his ma terials ; by regulating the supplies of air and fuel; by arranging his plant in the most economical manner, arid by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconsiruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, arid yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

By John T. Schamaun

Recent applications of explosives and blasting agents to rubble rock have led to requirements for more elaborate design and analysis methods. In most blasting uses, it is necessary not only to fracture the rock, but also to move the broken rubble in a predictable manner. Many in situ extraction techniques require rubblization to take place in a confined region where rock motion is a predominate factor in creating a permeable broken bed. In this paper, two analytical methods are presented which describe the large rubble motion during blasting. These methods provide the blast designer with a tool for evaluation and further refinement of blasting patterns and timing sequences. In both these methods, the rock medium is represented by a series of discrete, discontinuous regions. The use of discontinuous techniques rather than the classical continuum methods, results in better approximations to the rubble motion. These regions are set in motion by pressure loads from the explosive. The motion of these regions is then calculated numerically using interaction laws between regions in contact. The basis for these models or methods is presented along with the background for selecting explosive pressure loads and rock mass material behavior. Typical examples, including both cratering and bench blasting geometries, are discussed which illustrate the use of these models to predict rubble motion. Such engineering representations appear to provide a practical method for use in predicting rubble motion and a tool for design evaluation of blasting in confined geometries.

Jan 1, 1984