Search Documents

By N. Brown, M. Herman

ORDERING'S effect on the creep strength and other plastic properties of metals is unknown at the present time. Sachs and Weerts' attempted to compare the mechanical properties of the ordered and disordered state by comparing a quenched specimen with one annealed for a long time at a low temperature. This experiment is unsatisfactory because it introduces a possible effect from quenching. Barrett' used a hot impact test, but his method was not sufficiently sensitive to indicate any discontinuity in plastic behavior in the neighborhood of the critical temperature. On the theoretical side, Fisher9 as suggested that short range order would strengthen an alloy, but he gives no conclusions as to the effect of long range order. Cottrell" has discussed the interaction between long range order and dislocations, but does not indicate whether slip in a completely ordered alloy without domain boundaries is appreciably more difficult than slip in the disordered state. Because order exists in so many alloy systems, it is most important to prove experimentally whether long range order weakens or strengthens a metal. This investigation used -brass because: 1) it orders

Jan 1, 1957

By W. M. Clark

OUR interest in the matter of pyrometers and pyrometry is primarily that of a user of considerable quantities of heat-measuring equipment; and while we play be somewhat critical on the subject we have aimed to make the nature of these comments constructive. The glass industry in America dates back to 1609, when Capt. John Smith started a small glass plant near Jamestown, Va., with a few Italian workmen, to manufacture glass beads for trading with the Indians. While the industry has expanded until it has reached a volume of over $200,000,000 per annum, the means of heat determination in Colonial days was the human eye, and in much of the industry the same means is used today. About 15 yr. ago the largest glass-house supply dealers began to sell platinum pyrometers, but as nearly all of these proved un-satisfactory, pyrometers met a temporary rebuff from the old-time glass manufacturers. As their ruggedness of construction, reliability, and stability have been improved, however, pyrometers have gradually won their way into more and more extensive use throughout the glass trade. But there are still many applications where pyrometers are not used, largely because of cost and upkeep considerations. There are two distinct fields in glass works for pyrometry. The first calls for accurate temperature measurement and the second only demands knowledge of relative comparative fluctuations of temperature, to know whether the work is becoming hotter or colder. For example, in a lehr for annealing glassware and removing strain we want accurate temperatures to know that the ware is heated to the critical temperature for rapid removal of strain. On the other hand, in a glass pot furnace nearly 120 ft. (36 m.) in circumference, where the pyrometer couples only project inside the furnace wall for less than 2 in. (50 mm.), it is inconceivable that these few inches represent the accurate temperature at every point of the 120-ft. circumference but the relative readings as to whether the pyrometer shows schedule temperature fluctuations are valuable indications for control. The glass melting in the pots is,

Jan 8, 1919

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By Joseph W. Leonard

The purpose of this paper is to review and discuss some of the less evident and sometimes neglected opportunities for progressive developments in coal research. While a great deal of both promotional and technical information flows from some areas of coal research, output deficiencies in other areas of activity have reached a magnitude where important developments have been, and will increasingly be, unfavorably affected. These areas mainly involve coal mining and preparation. Some recommendations for the intensification of effort in these areas follow: Coal Mining While a huge tonnage of in-the-ground coal is assured, the location and distribution of these tonnages are becoming less favorable. The easy-to-mine coal which is located in or near population centers has been, or is being, mined. The vigor with which the less accessible reserves are recovered by the mining industry depends largely on the condition of the coal market at the time of mining. Hence, during a buyer's market, the commercially oriented mining industry is compelled to mine the easier and less costly reserves. Conversely, during a seller's market, the need to rapidly expand production results in more difficult mining and higher cost coal as few obstacles are encountered in finding markets. Hence, a seller's market tends to enhance the recovery of reserves while a buyer's market does not. One reason for today's fuel supply problems is that the Nation has recently emerged from a long-term coal buyer's market which lasted from about 1950 to 1968. During that period, national policy caused severe production cutbacks which regretably drove the industry to mining only the more accessible and better quality reserves. Often in order to remain in business, many hundreds of millions of tons of more difficult to mine reserves were abandoned and lost behind caved areas. Many of these reserves are close to population areas and would not have been lost in a more stable economic climate. It is difficult to fully account for all the impacts that were caused by the great buyer's market of the 1950s and 1960s. Besides the obvious loss of reserves that were once considered national wealth, the mining of better reserves tended to produce a generation of technically optimistic mining people. Mining people frequently became accustomed to looking at nothing less than outstanding mining conditions as a result of the declining market. Many are now and have long since received a re-education in the other half of mining. Going from many years of mining accessible, select and easy-to-win reserves, to the crash-driving of development entries in reserves that were considered unworthy of mining during 50s and 60s, frequently results in a much higher rate of encounter with in-seam and out-of-seam rock as well as with coal-deficient areas or "washouts." Intensive entry driving activity and compulsory non-selective mining in sometimes lean reserves were brought on by the need to rapidly open up new supplies of coal. Working under these requirements presents a continuing reminder that much more needs to be known about the relatively esoteric art of planning the best direction for driving entries in order to insure that a more consistent and greater supply of coal is available during early mine development. All of the preceding discussion tends to point to a need for a better estimate of those reserves of coal that are likely to be mined in the future. Such estimates should not be limited to the compilation of the amount of coal in the ground; but, where possible, should also include information concerning the capability for producing this coal. After all, a coal seam of ample thickness may have a degree of thickness variability, undulation, bad roof or floor, so as to make what would otherwise appear to be an attractive mining condition untenable. Underlying the problem involving the feasibility of producing known reserves is the need to develop better methods for the characterization of coal seams and associated lithotypes, based on drill core data, once at area is selected for mining. Reserves and their characterization involve aspects of exploration technology that are frequently considered mature. The resulting technological deficiencies may be the main reason why coal exploration frequently does not end with core drilling of a property, as it should, but extends into the mining operation during the driving of development entries. When exploration is extended to the driving of development entries, the near absence of integrated decision-making theory involving mining, geology, mathematics, and economics becomes, once again, all too painfully apparent and frequently results in very costly rationalizations. Hence, by the formal initiation of a concentrated program to combine the cyclical effects of economics with geology and mining, more relevant estimates of reserve distribution, tonnages, and production capability should be forthcoming. Moreover, a similar formal effort is needed to develop a combination of the most advanced concepts of mathematics, geology, and mining to better "see" coal seams as a means to favorably implement many long-range decisions involving mine safety and productivity. Much more applied research needs to be done on coal mining systems for mining in thin seams and/or under bad roof. Current difficulties in both of these areas at recently opened coal mines should provide a sobering glimpse into the future. Full-scale applied research, sponsored by appropriate federal agencies, is urgently needed on a scheme involving a new combination of established mining and preparation elements. The scheme may include: (1) a continuous mining machine remotely operated by a miner stationed at some distance behind the machine using a cord attached control box; (2) hydraulic transport of coal through pipes from the mining machine to a coarse refuse removal grid, crusher, and then on to portable concentrating equipment; (3) the hydraulic transport of clean coal out of the mine in pipes to the surface for thermal dewatering, if neces-

Jan 1, 1974

By M. E. Herrera

The use and effectiveness of sealants in under-ground mines is a recognized and well accepted practice by many people in the mining industry. Their use however in many cases is to correct, or attempt to correct, problems that might have been avoided with sealant use in the early stages of development, and continued thereafter.

Jan 1, 1982

By Milton E. Jennings

On May 11, 1977, the SAMARCO 508-mm (20-in.), 396-km pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO project. This paper presents the background, description, and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1982

By J. V. W. REYNDERS

THE principal manganese deposit of Russia, I one of the four principal sources of the world's supply, lies on the southern slope of the Caucasus Mountains, in what is now the Republic of Georgia, district of Sharopan. Tchiatouri, the principal town, is midway between Tiflis, the capital of Georgia, and Poti, the shipping port on the Black Sea, about 130 " miles distant. The deposit can be most easily visualized by thinking of a nearly horizontal coal seam about 6 ft. thick, outcropping on the slopes about 600 ft. above the Kvirila River. One of the accompanying illustrations shows the river, which nearly bi- sects the district, of approximately 50 sq. miles in area, and with its tributary streams makes the topography rugged, while in the background are the snow-capped peaks of the Caucasus range. Another of the illustrations gives a closer view of the outcrop. The roof and floor of the deposit are good, so the methods of working are quite similar to working a coal seam, especially as most of the mineral is soft enough to be mined with a pick. Little machinery is used, except small cars for underground transportation.

Jan 1, 1926

INTRODUCTION Besides the European export credit agencies covered in Ted Rides' paper in this Chapter, other agencies are also active (see Appendix) but the most notable for mining projects are The Export-Import Bank of the United States ("US Exim") and the Export Development Corporation ("EDC") of Canada. Mexico's Fomex is basically a short-term trade-finance fund administered by the Central Bank. US Exim This independent agency can provide loans, guarantees, and insurance. Like all export-credit agencies, its mandate is to support the export of goods and services from the US as a means of competing against other countries' products. If a piece of mining equipment can only he made in the US, the US Exim may very well not provide any financial assistance. (It is important not to place the order for any item for which export credit is sought because, once ordered, the situation is no longer competitive in US Exim's eyes.) Direct Credits and financial guarantees ("buyer credits") are commonly in amounts greater than 85 million and for terms longer than six years. An example here is the $48.5 million provided to PT International Nickel Indonesia (see Robert de Gavre's paper in Chapter 12). US Exim usually requires a 15% downpayment and, therefore, finances up to 857 of the goods; less if the US content is lower. The dollar funding can he US prime, London Interbank Offered Rate (LIBOR), or other sources. Exim can fund in either or both of the following ways: 1. Under a US bank Letter of Credit ("L/C") 2. Reimbursement to the buyer/borrower via a US bank account. US Exim will, without charge, issue a preliminary commitment. It will, however, need to approve the various credit agreements and prefers to tie other parallel financings into one loan agreement. US Exim's total commitments are large, up to $5R billion in aggregate under various programs. US Exim has been the world's leader in medium-to long-term minerals project financings/ co-financings but suffers from (i) aggressive foreign export-credit competition whereby other nations mix in soft-loans or aid programs ("mixed credits") to increase the percentage financed and lower the interest margin and (ii) an imbalance in its own cost of funds. A common US Exim package would be as follows: 15% Banks under US Exim guarantee, floating rate over prime or LIBOR. 35% US Exim funding, fixed rate 35% Pefco funding, fixed rate 857 Drawn down pro-rata under US bank L/C 15% Cash down payment (may have been financed within a project/corporate credit) 100% Repayment usually begins six months after planned start-up in equal semi-annual instalments, with the banks usually paid out first, Pefco next, and US Exim last. Medium-term credits ("supplier credits") are issued for US equipment exports for terms up to five years, again for 85% of the equipment costs although the exporter is expected to bear at least 10% out of that 857 for its own risk. The buyer is required to be a first-class credit such as some governments or highly credit-worthy companies. Otherwise a bank L/C would be required. (This may be wrapped into an overall project-finance package for a minerals development. The project-finance banks provide an L/C to US Exim instead of funding that portion themselves.) US Exim guarantees 100% of the political risk and either 85% or 95% of the commercial risk for

Jan 1, 1985

By David M. Cregger

The performance of the nation's first geologic repository for Commercial High Level Waste will be evaluated in a variety of ways which will involve the use of the state-of-the-art thermomechanical computer codes. Elastic properties of the host rock and the materials surrounding the repository are required for this numerical modeling effort to assess both near- and far-field effects. Only limited laboratory testing is possible, however, making it extremely beneficial to expand the data base by calculating dynamic elastic properties from available geophysical well logs. Elastic theory dictates that for an isotropic solid there are only two independent variables in addition to mass density, namely the compressional velocity, the shear velocity, and Poisson's Ratio. Compressional velocity and density are readily measured by geophysical well logs or in the lab; the crux of the solution requires measuring or determining either the shear velocity or Poisson's Ratio. Examination of acoustic propagated shear waves measured during confined compression testing demonstrates that Poisson's Ratio is a fundamental lithology-dependent parameter. Once a rock mass is appropriately classified, application of the laboratory derived dynamic Poisson's Ratio will yield a continuous and reasonable in situ modulus from acoustic and density logs. For preliminary characterization and assessment of the mechanical properties of rocks within the subsurface, and for studies of rock quality, this method is sufficiently accurate. The general availability of acoustic and density logs from wells logged for other purposes has made the application of this method desirable.

Jan 1, 1984

By H. G. Botset

ANY information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undis-turbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamina-tion by penetration of drilling water, since this problem has been exten-sively studied by other investigators. 1-3 Furthermore, it was regarded as being outside the scope of the present experiments, which were con-cerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essen-tial and obvious procedure is to vary systematically one factor or condi-tion while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program.

Jan 1, 1939

By Fred C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected.

Jan 5, 1958

By Joseph William Pinder

Every millman engaged in the operations incident to the handling of crushing-rolls knows that in ordinary practice, when fine product is desired, the ore-materials delivered to the machine, divided into four sizes, may be estimated, approximately, as follows : Per cent. Papsing a 4-mesh screen,..40 2- " " ........30 " 3/4-inch-mesh screen,.. 20 Larger,...........10 This estimate refers more particularly to the requirements of medium-sized rolls and fine crushing. But, depending largely on the character of work to be performed, the coarser material is often larger and of a greater percentage, while the bulk is always more or less fine.

Jan 1, 1899

By Howard L. Hartman, Burke O. Trafton

There is a fruitful area of computer competence which has gone virtually unnoticed by the mining industry. This is in the solution of its numerous fluid-flow distribution problems, involving the circulation of air, water and other fluids in conduits through mines. Typical of these is the mine ventilation system, which circulates air through mine openings to the working faces. The networks of interconnected airways in large mines-often resembling a tortuous maze or labyrinth defying representation by schematic, let alone solution-must somehow be resolved and analyzed, if effective and safe control of the ventilation is to be maintained. These are admirably suited to programming for solution by high-speed electronic computer. Not only can direction of flow be determined but quantity and head loss as well. EARLIER EFFORTS AT NETWORK SOLUTION The only prior attempt to solve mine ventilation networks by digital computer methods was made by a Japanese investigator1 in 1958 whose work went unpublished. Unfortunately, he employed a method of network analysis little used in the United States and one which could accommodate a maximum of only 30 airways. While his analysis seems unnecessarily cumbersome and involved, it did suggest that a digital computer approach was feasible.

Jan 9, 1963

By G. A. Vissac

MoIstuRe in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain"). These latter forms of moisture are particularly common in "young" coals (subbituminous and lignites); bloom coals (seam outcrops); fusain; and carbonized products. In our study of coal drying, we shall consider only the removal of free moisture, exclusive from hygroscopic moisture. Dewatering If we reserve the name of drying to the removal of water by evaporation, we must consider the initial phase of the mechanical removal of free moisture as a distinct operation covered by the term dewatering. In all cases the free water carried over the surface of the coal particles or in their interstices, or in their pores, is retained by capillary forces. Dewater-ing is accomplished by breaking or counteracting these capillary forces; removal of as much water as possible by dewatering methods is usually advisable, as the cost of these operations is generally much less than by evaporation. The most common methods of me-chanical dewatering are: 1. "Pressure piling," which reduces the interstitial spaces, accomplished in dewatering bins or over dewatering screens. 2. Or dynamic methods, such as used in centrifuges or over vibrating screens. We shall only mention the " preferential wetting" method, in which surface water can be displaced by hydrocarbons, as offering possibilities, but which, to our knowledge, has not reached yet a practical development. But we must point out that the capillary forces retaining water on the coal surfaces, decrease considerably with increased temperatures. This is the principle used in all modern dishwashing machines; by using very hot water, dishes are extracted almost dry. In line with this development, we favor the type of dryers including a dewatering section; as the coal enters the dryer and is gradually brought up to higher temperatures, its dewatering ability is increased and advantage can be taken of this conditioning, resulting in increased drying efficiencies and reductions in drying costs. Heat Drying In the final phase, the remaining moisture must be evaporated. Coal and water must be brought up to the chosen temperature of evaporation, and heat must be supplied to fill the requirements of the latent heat of evaporation of the water to be removed. Accordingly, drying becomes largely a problem of heat transfer, and drying methods can be classified accordingly, namely: 1. Radiant transfer. 2. Transfer by surface contact and conduction. 3. Transfer by hot gas contact. The first method is not applicable to coal drying; the second method is used in the old type rotary dryer. The third method, the most commonly used in modern coal dryers, will be the only one considered here; and, of course, we shall deal with continuous types of dryers only. The mechanism of complete drying is really very complex-—several phases are involved: 1. The constant rate period. 2. The uniform falling rate period. 3. The varying falling rate period. As most of our practical coal drying problems deal with wet coals (over 6 pct of moisture), and do not require complete drying (under 1.5 pct), we shall deal with the first condition only, namely the constant rate drying. Dryer Calculations Instead of presenting the algebraic formulas, we believe a concrete example will provide a clearer illustration. Assume a feed of wet coal at the rate

Jan 1, 1950

Announcement is made that applications fir the Emmons Memorial Fellowship in Economic. Geology will be considered, and an incumbent appointed prior to the first of June. Applications should be sent to Professor J. F. Kemp of Columbia University not Intel: than May 15. . The holder of this fellowship receives an income of $1,000 and is expected to carry on an investigation in Economic Geology which will add a distinct contribution to the literature. The institution at which the study is pursued will be decided after conference with the members of the Committee of Awards. The character of the investigation will be decided after applications have been passed upon.

Jan 5, 1917

By Horace Pops, L. L. Isaacs

SOLID-STATE transformations at low temperatures are frequently studied by optical metallography. Greninger and ooradian' and Hull and Gar-wood2 have examined the martensitic-type transformations in 0-phase Cu-Zn alloys during continuous cooling below room temperature. The lowest range of temperatures in the apparatus described by these investigators is limited to approximately 110°K. Present studies of reversible first-order phase transitions near liquid-helium temperatures have necessitated the design of a new cold-stage cryo-stat for optical metallography. The features of interest of this instrument are as follows: a) temperatures down to 4.Z°K are obtainable; b) the specimen is always under vacuum, thereby avoiding the condensation of moisture; c) specimens can be rapidly cooled or heated at varying rates, thus permitting studies of transformation hysteresis. Fig. 1 shows the details of the cryostat. All major parts are made of type 304 stainless steel. Both helium and nitrogen cans are Heliarc-welded to the helium filling tube, permitting the use of a common shielding can. Hence, the over-all weight and the area of the evacuated surface are mini- mized. The copper sample holder is screwed into the bottom of the helium can. To assure good thermal contact between the sample holder and the refrigerant, an indium ribbon is placed on the threads

Jan 1, 1964

INTERNATIONAL ENGINEERING CONGRESS This Congress will be held under the auspices of five National Engineering Societies, of whi h the Institute is one. The sessions will be held in 11 sections and the proceedings will be published in 10 volumes of 500 pages each, of which Volume 8 will contain the papers and proceedings on Mining Engineering and Metallurgy. The membership fee of $5 will entitle the holder to the volume of General Proceedings and Index, and, in addition thereto, any other single volume chosen. Other volumes may be subscribed for according to a sliding scale depending upon the number of volumes taken. The Institute will have a meeting in San Francisco during 1915, and it is desirable for our members to join the International Engineering Congress at in early date in order that their support of the enterprise may be given in its early stages, when it is most needed.

Jan 2, 1914

By T. C. Shelton, W. M. Huang

One of the problems arising from the use of modern machines and systems in coal mining is increased emission of explosive gases into the mine passageways. Interest in degasification of coal seams has grown. The authors summarize the results of coal permeability tests done at Virginia Polytechnic Inst. on one of the fundamental aspects of the problem. There are undoubtedly many factors that affect the emission of gas from coal but the permeability of coal to gas flow would seem to be fundamental. However, there is very little information on coal permeability to gas flow available in the U.S. at the present time, despite the fact that such knowledge would appear to be significant in any degasification effort. Studies made recently in the mining engineering laboratories at Virginia Polytechnic Inst. have determined values of permeability on 1-in. cubes of selected coals. COAL PERMEABILITY The permeability values given in this paper are based on adaptations of Darcy's law formulated by Henry Darcy in I856 from experiments with fluid flow in porous media.' Using air as the gaseous fluid, they were obtained by employing similar methods as are used to dete1:mine the permeability of petroleum and gas reservoir rock specimens. Permeability is. a measure of the ease with which fluids flow through a porous substance, and it is governed by the connected pores within a porous medium. If a few large-sized pores, fractures or channels are present within the medium, the medium can have great permcnability without significant porosity. It is reasonable to assume, therefore, that the permeability of coal, due to its structure, is based on fractures connecting the pore space left as the result of some degree of devolatilization or other changes of the substance from which coal was formed. The results of this irvestigation tend to validate this assumption in that the values obtained indicate a close relationship between the rank and permeability of coal. COALS TESTED AND PROCEDURE The coals whose permeability values were determined in this investigation are given in Table I.

Jan 1, 1962

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957