Search Documents

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By William B. Plank

PRESENT enrollment of 182,361 students in the engineering schools of the United States and Canada represents an increase of 6.6 pct over the enrollment in these schools in 1951-52. Thus is brought to a halt the steady decrease in engineering enrollment that began with the close of the 1947-48 academic year, five years ago. The mineral engineering student picture is similarly encouraging. In the United States schools, 9453 students are preparing themselves for positions in the Mineral Industry. This is an increase of 8.3 pct over last year as compared with an increase of 6.6 pct in the total United States engineering enrollment. The rate of recovery for the mineral engineering group is thus more rapid than for the engineers as a whole.

Jan 4, 1953

By John Dasher, M. C. Chang

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to beneficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly -24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant.

Jan 3, 1959

By Malcolm V. Lowry

At Balmat in northern New York State, the St. Joseph Lead Co.'s 2100-tpd zinc mining and milling operation is utilizing a unique thickener in conjunction with conventional crushing, grinding and flotation methods. From 1930 through 1962, zinc concentrates went directly from flotation to the filtering, drying and loading facilities, all of which had to operate 24 hr per day. Wide fluctuations in tonnage also had to be accommodated due to variations in the grade of ore. Many problems were thus encountered in filtering and drying, but the cost of installing a conventional, large diameter thickener could never be justified. In 1963, after thorough investigation, an unconventional thickener that is unusual in several respects was installed at Balmat. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes.

Jan 5, 1966

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By M. D. Cooper

LUCIEN EATON, Ishpeming, Mich.-It is not the custom in the Lake Superior region, as far as I know, to employ shot-firers. Each man, or pair of men (most of the contracts are given to two men) do their own firing; each contractor keeps his powder separately. The general custom is to distribute powder (dynamite only is used) to the mines 2 days a week. The boxes, marked with the contract number and the level, are taken underground and the men take them to their working places. They are kept in boxes, which must not be nearer together than 50 ft. and are usually away from the timber roads or traveling roads. When holes have been drilled, one man usually takes down the machine, and the other man makes up the charge. He cuts the fuse, puts in the caps, etc., at a distance from the powder box. He then carries the powder charges to the working place where both men charge the hole. They do their own firing and warn others coming from any direction that the holes are being fired.

Jan 4, 1917

By Frederic Dewey

BONE-ASH cupels have been used from time immemorial to absorb litharge, and accompanying oxides; in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge 1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at present it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 11, 1917

By W. T. Cardwell

This paper presents a theory for estimating the rate of gravity drainage of a liquid out of a sand column. Account is taken of the variation in permeability to the liquid as the saturation in the upper part of the sand becomes less than 100 pct. The theory is confirmed by previously published experimental data. Introduction Petroleum engineers have expressed the need for 4 theory of gravity drainage. Brunner,' in particular, has pointed out that some type of mathematical theory is necessary to begin the application of laboratory data to field problems. Muskat and his associates2'3-4 have recently made contributions to the theory of gas-drive behavior and have indicated an intention to apply their methods to water-drive systems. No theory of gravity drainage rates has been developed, however, and it seems desirable to formulate one at this time. Differential Equations of Capillary Flow The flow of liquids in partially saturated porous media has been studied by many investigators.6-10 Richards6 presented derivations of fundamental differential equa- tions governing two-phase capillary flow; and used simplified forms of those equations in solving a steady-state problem. Muskat and Meres6 presented and used equations different from those of Richards. Their equations did not explicitly involve capillary pressure gradients; but included, on the other hand, terms expressing the effects of the evolution of gas from the liquid phase during flow. Leverett8 stated in 1940 that "previous work on the flow of fluid mixtures in porous solids [had] failed adequately to account for all of the three influences that cause motion of the fluids: capillarity, gravity, and impressed external pressure differentials." Leverett's basic equations, however, were specialized forms of the general equations of Richards,5 which had actually taken account of the three influences mentioned by Leverett, but had not been used in a problem involving all three. The fact is that our knowledge of capillary flow and our ability to express this knowledge in differential equations exceed our ability to solve the equations except in a few cases. General differential equations have usually been of little more than formal value. In solving practical problems, it has been necessary to develop specific equations, preserving terms that involved the factors important in those problems, and purposefully neglecting other terms that were not of predominating influence. This is the method followed here. It is believed that the solution of the particular problem and the scheme of the solution itself are new.

Jan 1, 1949

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

By F. P. Dewey

Bone-ash cupels have been used from time immemorial to absorb litharge, and accompanying oxides, in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at resent it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 1, 1918

It has been established that molybdenum sesquisulphide, not molybdenite, is in equilibrium with molybdenum metal and sulphur vapor in the vicinity of 1100°C. The S2 pressure for this system has been obtained using the Knudsen orifice method and the standard free energy for the dissociation of S2. THIS work was undertaken to help in determining the thermodynamic properties of the molybdenum sulphide which is in equilibrium with metallic molybdenum and sulphur vapor in the temperature range 1025" to 1150°C. From the results of MontoroL and of Parravano and Malquori' molybdenite would be expected to be in equilibrium with molybdenum metal, while the results of Guichard indicate that a lower sulphide must be in equilibrium with the metal. Thus it was concluded that the problem warranted reconsideration, especially in view of the suspiciously low temperature independent term for the standard free-energy function for the reaction MoS² Mo + S,. The reaction was calculated and duly noted as being low by Richardson and Jeffes,' using the data of Parravano and Malquori.' Experimental Method The general method used in this investigation is that of the Knudsen orifice method for the determination of equilibrium pressure. The apparatus and technique are similar to those described for the determination of the vapor pressure of silver.% owever, a closed-end McDanel tube instead of fused silica was used to maintain the vacuum, a molybdenum effusion cell with a replaceable lid was employed instead of a silica cell, and a titanium getter maintained at run temperature was used to assure that no oxidation of the molybdenum or molybdenum sulphide was taking place. All runs were made at a residual pressure less than 10-5 mm Hg. The data are given in Table I. Runs 1 through 13 were obtained using molybdenite, analyzed 98.5 pct, from the Molybdenum Corp. of America. The remaining runs were done with a sample from the Climax Molybdenum Corp. which was their grade No. 3 and analyzed 59.87 pct Mo. The weight loss of the cell during heating up and cooling down was subtracted from the total weight loss of the cell during the run. Also, when the tem- perature was changed, the Knudsen cell was placed in the vacuum chamber and heated at temperature for several hours in order to allow the sulphide and the metal to adjust their compositions to the equilibrium values, to desorb or adsorb gases into or from the molybdenum cell itself, and to desorb any water from the molybdenum sulphide or molybdenum powder inside the cell. Water may have been adsorbed inside the cell because, after each run, the top of the cell was removed and the material in the cell was stirred to insure that a layer of molybdenum metal would not build up and obstruct the passage of sulphur vapor into the gas phase. It was established that the molybdenum cell alone decreased in weight an inappreciable amount when heated at the highest run temperature for long periods of time. There are two questions to be answered before the data in Table I can be used to calculate thermodynamic functions: 1—Which molybdenum sulphide is in equilibrium with molybdenum metal and sulphur vapor? 2—What sulphur species are present in the vapor phase? It can be assumed safely that no molybdenum is vaporized, since its vapor pressure is almost negligible at these temperatures. It will be shown subsequently that no sulphide of molybdenum is volatile. Question 1 was answered in the following way: The especially purified molybdenite, obtained from the suppliers mentioned previously, was charged

Jan 1, 1956

By Leonard E. Wood, Yeghishe M. Avedissian

Knowledge of the basic properties of rocks-strength, structure, and permeability-is prerequisite for the success of foundation work for masonry dams, large bridge piers, and tunneling as well as for excavation in rock and special underground construction. Strength of engineering materials depends upon texture and structure as well as the environmental conditions to which they have been subjected. Failure in its widest sense implies the transition of a material from elastic to plastic state (yield strength), from continuous to discontinuous state (rupture strength). The compressive strength of a material such as rock is the stress at which a sample, loaded and unconfined at the sides, fails by rupture. Some of the external factors that control strength of rocks are the nature and type of stress, whether uniaxial or triaxial, compression, tension, or torsion. Another important factor is the rate of stressing-whether constant, impact, or gradually increasing. Of the internal factors, the effect of texture upon strength is obvious. Generally, fine-grained rocks have higher compressive strength than coarse-grained prototypes. Among metamorphic and igneous rocks those with better and higher degree of interlocking of their crystals are generally stronger than the ones with poor or lower degree of interlocking. In sedimentary rocks, the degree and type of cementation has a great influence upon their strength. Structurally, the existence of fissures, cracks, and seams of argillaceous or organic materials in a rock specimen will greatly reduce its strength. Because most rocks are characterized by bedding planes, laminations, or foliations, they are anisotropic in their physical properties and hence compressive strength depends on the orientation of the bedding planes to

Jan 1, 1972

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By E. P. Pfleider, W. D. Lacabanne

ROTARY-percussive drilling is a new method of drilling hard rock. Designed to give variations in thrust, revolutions per minute, and torque ranges, these drills combine the high efficiency of the rotary system in soft rocks with an increasing amount of percussive action in rocks more difficult to fragment. Fundamentals of the rotary, percussive, and combination systems have been described in detail in various papers-most recently by C. Fairhurst and W. D. Lacabanne1-but there is still much basic work to be done on the interplay of actions in the rotary-percussive system to enable the drill designer to achieve the highest efficiencies. Whereas the original units struck light blows of only 15 to 30 ft-lb, adequate for medium hard rocks, the present trend is to piston blows of 50 to 65 ft-lb in order to cope with the granites and other rocks having Shore hardnesses of 75 or more.

Jan 7, 1957

By Edward Nichols

These deposits, which are found in James County, Tennessee, differ both in their mode of occurrence and in their chemical constitution from any other ores belonging to the same geological horizon which are known to the writer. Taylor's Ridge, or White Oak Mountain, is a long monoclinal ridge, which starts from a point near the Tennessee River in Meigs County, and, following a southwwt .course, extends unbrokenly into Cherokee County, Alabama, where it finally disappears. It is made up of strata of the Upper Silurian rocks, which dip to the southeast. To the eastward of this ridge, which is generally several hundred feet high, are a series of low foothills or knobs, composed of Clinton shales carrying seams of fossiliferous hematites. In the neighborhoud of the East Tennessee, Virginia, and Georgia Railroad, where it crosses the ridges, considerable ore has been milred from these seams during the pst ten years. Most of the workings have been superficial, and the ores mined, with one exception,,carry a silicious and nod-calcareous gangue, and contain from fifty to sixty per ceut. of iron.

Jan 1, 1882

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model'h nd the fluid mapper technique for the solution of certain problems.' The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

RESEMBLING in some respects the enterprise at R Chuquicamata is that of the New Cornelia Copper Co. at Ajo, Arizona. Controlled from its inception by the Calumet & Arizona Mining Co., New Cornelia became a unit of the Phelps Dodge Corporation when the latter absorbed the Calumet & Arizona company in 1931. Both Ajo and Chuquicamata are situated in low mountains in extremely arid desert country. Both ore deposits consisted-the past tense is used advisedly because the oxidized ore has nearly all been mined at Ajo-of a horizon of leachable oxidized ores overlying sulphide or concentrating ore. The principal technical problem in each case was the development of a method for treating the oxidized ore. In both instances the capping of waste rock was comparatively thin and power-shovel mining in open cuts was the obvious method of exploitation. Nature had smiled on neither place in the matter of climate. Though Ajo does not have the persistent winds for which Chuquicamata is notorious, the comforts of living are largely artificial. And it is only fair to emphasize that at each place the mining companies have achieved remarkable success in providing these comforts. Of course, in point of size New Cornelia must be content with the inferior role. From May, 1917, when production was started, to the middle of June, 1930, the company leached 16,368,000 tons of oxidized ore, thereby virtually exhausting the ores of this class. Up to the same date, about 15,000,000 tons of sulphide ore had been mined, and a rough estimate gives 170,000,000 tons remaining in reserve. The total tonnage does not loom very large in comparison with Chuquicamata's billion tons; but it is exceeded by similar figures for only four of the Porphyry group.

Jan 1, 1933