Search Documents

By BLAllEY STEVENS

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. TEH object of this paper is to show how igneous intrusion is governed by definite mechanical laws. A distinction is made between dikes and fissures, and the various characteristics of intrusions are explained on an exact scientific basis. The modification of rock-stresses by intrusion is then considered and extensive isostress regions are recognized. Finally, a complete classification of intrusions is constructed covering all pos-sible cases. The generalizations of observed data, taken from Geikie's Textbook of Geology, conform to the laws of intrusion herein stated, and the deductions based upon these laws. No authority, however, is quoted for the type which I have named a corrugated intrusion. Its existence is a necessary deduction from the laws of intrusion, and even the entire absence of examples in technical publications cannot disprove its reality. In all probability, corrugated fissures would have remained undiscovered, but for the working of mineral veins. As intrusions of tabular form are seldom worked for commercial purposes, it has been left for theory to anticipate the discovery of corrugated dikes. In the light of these laws of intrusion and the corresponding laws of fissures,1 there seems to be a remarkable uniformity of stress-distribution in rocks at moderate depths. This renders .possible the mathematical calculation which should help us to approximate exact science in this and kindred branches of applied geology.

Jan 1, 1911

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in. the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By S. S. Clarke

LATE in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls Were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1947

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

By Sidney Powers

INTRODUCTION THIS paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Fundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Mines, Mines Branch, Ottawa,1 all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of -Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 min. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grains per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 2, 1916

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard. Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson, It will be noted that the various interests of the iron and steel industry are authoritatively represented on this Committee by producers of raw materials (iron ore, coke, and other fuels, refractories, etc.) and of finished materials, by consumers, consulting metallurgists, and educators. The primary duties of the Committee are to secure important papers on iron and steel, to promote their discussion, to organize lively and fruitful meetings, and otherwise to foster the interests of the large number of members of the Institute connected with the iron and steel industry in its many phases. Its success during the past year has been noteworthy. Through its instrumentality many valuable papers were presented at the Cleveland and New York meetings, followed by animated and productive discussions, while the attendance of iron and steel men at both meetings was remarkably large and representative.

Jan 5, 1913

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By Fred D. DeVaney

DURING the past few years a radically new process for the magnetic roasting of iron ores has been investigated and developed by Pickands Mather & Co. and the Erie Mining Co. in the Erie laboratory at Hibbing, Minn. This process, originally devised by Dr. P. H. Royster of Washington, D. C., involves the use of a roasting technique quite different from older methods. It has now been demonstrated that iron-bearing materials can be roasted as effectively as by any previously known method, and at a much lower cost. The increasing shortage of highgrade iron ores in this country has accelerated the search for new methods that would permit low grade materials to be utilized. The concept of magnetically roasting low grade nonmagnetic ores such as the oxidized taconites and then separating such material magnetically has always had considerable appeal. The magnetic concentration idea is attractive because of the sharpness of the separations and cheapness of the method. Heretofore, however, the equipment and the processes available for the magnetizing-roasting -step have left much to be desired. The customary equipment available for reduction roasting has been: 1-multiple hearth furnaces, 2-rotary kilns, and 3-shaft type kilns. In addition, it is understood that some work has been done in magnetically roasting fine ores by a process using the FluoSolids principle, but little information on this process is available. The multiple hearth kiln has been used the most but first costs and operating costs have been high because of low capacity, high maintenance, and poor gas utilization. Magnetic roasting can be done in a rotary kiln, but the radiation losses are high and the conversion to magnetite is usually unsatisfactory because of poor contact between the gases and the solids. Of the shaft-type furnaces, probably the most efficient yet developed is that designed by E. W. Davis of the Minnesota Mines Experiment Station. This furnace was operated at Cooley, Minn., during 1934-1937 but was abandoned in 1937 because the operation was uneconomic. Heretofore the basic concept behind most magnetic roasting processes has been the idea of heating iron ore to a temperature of 800° to 1100 °F in a strong reducing atmosphere, preferably either carbon monoxide or hydrogen. Temperatures under 800°F were undesirable since excessive roasting time was required. Temperatures over 1100°F were avoided because of the danger of converting part of the iron to ferrous oxide which is nonmagnetic. In the new roasting process, the operation is carried on in a shaft furnace using a controlled atmosphere containing a low percentage of reducing gas. The temperature in the roasting zone is considerably higher than with the usual reducing gas and this speeds up the reduction time. Portions of the spent furnace gases are cooled and recirculated and this together with the good contact between ore and gas makes for high reducing gas utilization. High heat economy is secured by recuperating heat from the roasted ore by passing the cold reducing gases countercurrent to flow of ore. The heat transfer principle is similar to that employed in a pebble stove and to that used in the Erie Mining Co. furnace at Aurora, Minn., for pelletizing fine magnetite concentrates derived from taconite. The theory of controlled atmosphere during the roasting operation can best be appreciated by inspecting the equilibrium diagram of the Fe-C-O system shown in Fig. 1. An inspection of this diagram shows that in certain areas magnetite, Fe3O4, is the only stable form of iron. A further inspection of this table shows that if the proper ratio is maintained between carbon dioxide to carbon monoxide, such a gas will be reducing with respect to hematite, Fe2O3, and will be oxidizing with respect to both ferrous oxide, FeO, and iron, Fe. It should be kept in mind that the formation of ferrous oxide in a roasting operation is harmful, since this oxide is nonmagnetic; if it forms in any quantity, it will cause substantial loss of iron in the ensuing magnetic separation step. If a ratio of approximately three parts carbon dioxide to one of carbon monoxide is maintained, the resulting operation can be carried on at a relatively high temperature without fear of over-reduction. Specifically, most of the tests in the Erie furnace have been made at a temperature of 1500° to 1600°F, with an entrant gas containing approximately 5 pct carbon monoxide and 15 pct carbon dioxide, with the remainder largely nitrogen. It should be remembered that the ratios of carbon monoxide to carbon dioxide shown in Fig. 1 hold even though the bulk of the gas is an inert gas such as nitrogen. It may surprise many to learn that a gas containing as low as 3 pct carbon monoxide, and 12 pct carbon dioxide with the remainder nitrogen is an extremely effective reducing gas in the 1000° to 1600°F temperature range. The reducing gas is not limited to carbon monoxide, and mixtures of hydrogen and carbon monoxide may be used effectively, provided that a similar ratio is maintained between the reducing gases and carbon dioxide and water vapor. For a more detailed explanation of the theory involved, the reader is referred to U. S. patents 2,528,552 and 2,528,553. From a safety standpoint, the weak reducing gas used in the furnace offers an advantage. Its composition is such that it is well below the limits of explosion should air enter a hot furnace. This condition is not true with the usual reducing furnace, in which a gas rich in carbon monoxide or hydrogen is used. The general furnace design and method of operation may best be understood by an inspection of

Jan 1, 1952

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

Electrocarbonization of coal will produce cheap fuel for electric power plants. The complete electrification of industry and domestic power consumption of gas generated as fuel in situ is a worthwhile goal for the coal industry. Production of synthetic oils, gasoline, and coal chemicals from coal gas will create additional new markets for the coal industry. RANKING high in the nation's wealth of natural resources, readily available liquid and gaseous hydrocarbons are nevertheless falling steadily in supply, while industrial requirements for hydrocarbon compounds are greater today than during the peak period of World War 11. Theoretically, several processes will increase the future supply of liquid and gaseous fuels, but the practical application of these methods depends on two controlling factors: 1—that enough carbon-bearing material be available to warrant industrial exploitation, and 2—that the given process be physically, chemically, and economically applicable. With regard to the first factor, the Western Hemisphere is fortunately well supplied, see Table I. Table I not only shows the extensive occurrence of many fuel sources, but also the wide discrepancy among quantities of fuel substances in various materials. Great quantities of potentially available fuel have not been recovered. Many coal seams and other hydrocarbon-bearing deposits are so situated that production is uneconomical by present-day mining or oilwell pumping methods, and even in many exploitable deposits where the most efficient production methods are used a large proportion of material is never recovered. Industrial production of hydrocarbon liquids and gases must be better balanced, and processes must be developed which will convert coals, oil sand, and oil shales into fabricated commodities. Among the techniques employed by scientists and engineers to secure fuel masses not economically available at present are several processes of underground gasification. These are all concerned with converting raw materials into gaseous products by thermal treatment of source substances while they are still in the ground and therefore require that a subsurface heat (fire) zone be induced to affect pervasively the buried raw fuel deposit. This is possible only where sufficiently high temperature exists and where the fuel material is satisfactorily opened or channelized. Also, to compete successfully with common mining or oilfield practices, a given method must be controllable and must not involve greater operational expense than regular methods. Preferably, it should be less expensive. Since the close of World War 11, England has continued field studies of underground gasification methods. Experiments have also been conducted in Sweden, Estonia, France, Belgium, Italy, and Germany. The U. S. Government has sponsored field studies at Gorgas, Ala., and because gasification in situ is vitally important to establishment of the nation's fuel resources, the mining engineering department at the Missouri School of Mines has been actively interested in developing the process of underground electrocarbonization. Research was conceived by Erich Sarapuu, and preliminary experiments in treating bituminous coal were begun at the school in September 1947. The work consisted of laboratory experimentation until June 1948, at which time, through a cooperative agreement with the Sinclair Coal Co. of Missouri, pilot plant studies were instituted at the Tiger mine of the Hume-Sinclair Coal Co. near Hume, Mo., to test the encouraging laboratory findings. This comprehensive field program was pursued continuously until the beginning of 1952."'" The broad term underground electrocarbonization describes a unique gasification process that releases by electricity the desired economic constituents from a raw carbon-bearing material, converting the substance of such deposits into deliverable form and greatly reducing the cost-of-mining factor. Underground electrocarbonization is not subject to the major limitations of many other underground gasifi-

Jan 1, 1955

By AIME AIME

EVEN the weather man joined in a friendly conspiracy to make the fall meeting of the Industrial Minerals Division at Rolla, Mo., Oct. 23-25. the splendid surges that it was. Following weeks of rain, the foliage of the Ozarks was still green, merely enlivened here and there by splashes of autumn coloring. In contrast to the tranquil beauty of the School of Mines campus under smiling Indian summer skies, the pace of the meeting was lively. Registration was larger than at any previous meeting and included an unusual number of prominent names and delegates from all over the country. From 125 to 150 were present throughout the three technical sessions, at the Thursday evening smoker, and also at the banquet on Friday; when students trooped in to the technical sessions the audience was augmented occasionally to over 200.

Jan 1, 1941

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942

By Frank G. Norris, William C. Marshall

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, ' others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By William C. Marshall, Frank G. Norris

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, ' others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By R. S. Archer

IN the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the heat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis; heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while iii others, especially ill those whose grain is unusually fine or in which the final hardening heat, has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters.

Jan 1, 1919

Industrial minerals enjoyed a fairly successful year in 1978, despite the sluggish economy, inflation, and environmental restrictions. A glance at US Bureau of Mines statistics shows that, in general, production of industrial minerals increased from + 1% (salt) to as much as 26% (sulfur, other than Frasch or recovered). A few industrial minerals showed a decline; fluorspar production, for example, registered a 23% decrease in 1978 from 1977 due to the closing of three domestic mines. Bromine, natural sodium sulfate, Frasch sulfur, and vermiculite also had production decreases of 2-6% in 1978.

Jan 5, 1979

By J. Spotts McDowell

Ackowledgments........................... 5 Introduction............................. 5 The Silica Minerals. Stability Relations......................... 6 Optical Properties........................ 9 Density.............................. 10 Melting Points....;..................... 10 Thermal Expansion..................,..... 10 Solubilities............................ 12 Identification of Cristobalite and Tridymite.............. 12. The Silica Refractories. Raw Materia1........................... 13 American Deposits....................... 13 Properties Determining Usability................ 15 Expansion on Heating..................... 16 Texture........................... 17 Silica Brick............................ 17 Manufacture........................... 18 Properties of Silica Brick .................... 19 Analysis ......................... 19 Density......................... 19 Porosity......................... 20 Strength....................... 21 Melting Point....................... 22 Specific Heat....................... 22 Thermal Conductivity................... 23 Expansion........................ 24 Effect of Rapid Temperature Change.........:... 26 Constitution......................... 26

Jan 1, 1918

By A. W. Ashbrook

There are many methods of analysis available for compounds similar to those used in solvent extraction processes. However, the majority of these methods are not directly applicable to the determination of solvent extraction reagents, especially in raffinates. The number which are applicable is further reduced if limited to the more simple methods suitable for process control purposes. Commercial extractants are complex mixtures. The complexity is increased by the addition of diluents and modifiers in two-phase systems containing metals. Raffinates from solvent extraction processes contain the more polar components of the extractants and the products of decomposition. Only a limited amount of information is provided by total organic carbon or spectrophotometric analysis. The complexities of the systems require a combination of methods.

Jan 1, 1978

By Philip B. Bucky

CONTENTS [PACEPACE r. What Is a Rock Burst?2 4. How Can Rock Bursts Be Predicted? . 35 Jack Spalding2Jack Spalding35 A. F. Robertson 2, 5A. F. Robertson35 W. R. Crane 2A. B. Yates and P. J. Shenon. . . . 35 G. S. Rice 2W. R. Crane 35 P. J. Shenon 2G. S. Rice 35 L. C. Graton 2B. F. Tillson 36 2. What Are the Causes of Rock Bursts? 6 5. How Can Rock Bursts Be Controlled?. 36 Jack Spalding6Jack Spalding36 A. B. Yates and P. J. Shenon . 7, 12, 29A. F. Robertson 36 A. F. Robertson 12, 28W. R. Crane37 W. R. Crane 15A. B. Yates and P. J. Shenon. . . . 37 G. S. Rice 15Oscar Weiss38 Oscar Weiss15G. S. Rice37, 42 P. B. Bucky21R. D. Hoffman42, 43 P. H. Bird 21, 26, 28R. D. Hall 42 M. K. Hubbert26R. H. Cromwell42 G. Wheeler 26. J. Shenon 42 B. F. Tillson26, 28P. B. Bucky42, 44 T. T. Read 27B. F. Tillson 42, 44 A. B. Yates 43, 44 3. How Can Rock Bursts Be Prevented? . 30P. H. Bird 43 Jack Spalding. . . . • . • • • • . 306. General Discussion . A. B. Yates and P. J. Shenon. . . . 31Jack Spalding44 A. F. Robertson32R. D. Parker49 W. R. Crane 35C. Baring Horwood 51 G. S. Rice 35P. B. Bucky 52] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942