Search Documents

By Frank Ittner

In this section it is proposed to discuss operating methods considered good practice under the various field conditions commonly encountered. Efficient field direction and types of equipment needed to meet transportation problems are considered only to the extent that the desire to produce the best possible records must sometimes give way to the factor of cost. As in all engineering projects, alternative possible methods of operation must be considered in the light of relative costs as well as of the quality of results obtained, Cost may be in the background of much that is done in the field operations, but only the effect on record quality will be considered here. Record quality at a particular shot point may vary with the various factors of spread character (relative positions of geophones and shot point), shot-hole depth, formations opposite position of shot, size of charge, the effect of repeat shots, surface geology and culture in the immediate vicinity of the geophones, recorder instrument characteristics, particularly filter.

Jan 1, 1940

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

[ ] For President-Elect Leo F. Reinartz has been nominated for the Presidency of AIME in 1954. Mr. Reinartz is now vice-president, special operating development, Armco Steel Corp. He was born in East Liverpool, Ohio, and graduated from the Carnegie Institute of Technology as metallurgical engineer. He joined Armco in 1909 as a chemist and then became open hearth foreman; assistant superintendent, open hearth dept.; superintendent, open hearth dept.; assistant general superintendent; works manager, East works; manager, Middletown div.; and assistant vice-president, successively. Mr. Reinartz has been active in many technical societies and delivered papers before several. He has been the recipient of the Alumni Award from Carnegie and holds life honorary membership in the AIME National Open Hearth Conference. One of the organizers of the National Open Hearth Conference, Mr. Reinartz was Chairman, Executive Committee (1927 to 1946) and is presently Chairman of its Finance Committee. In October 1951 he was an American Conferee at the First World Metallurgical Congress held in Detroit. An AIME member since 1925, Mr. Reinartz has been active on numerous committees of the Institute.

Jan 1, 1952

By J. A. Dresser

The controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec.

Jan 1, 1915

By Sylvain J. Pirson

The question of the interpretation of apparent resistivity curves is still a much disputed subject although the discussion has been going on for several years, mainly since Gish and Rooneyl made their first measurements on the Tidal Basin at Washington, D. C. As a first approximation, they interpreted the depth to a horizontal discontinuity in terms of the electrode spacing at which a maximum or a minimum occurs in the resistivity curve. Later on, Lancaster-Jones2 proposed a closer approximation of depth determination by evaluating the depth to a horizontal discontinuity as the two-thirds of the electrode spacing at which a point of inflection occurs in the resistivity curve. An accurate determination of the depth was recently proposed by Tagg3 for a two-layer problem. It is a graphic solution of the problem by means of charts calculated from the formula of the apparent resistivity based on the theory of electrical images. Tagg's method is theoretically sound but the fact that the layers have been assumed to be homogeneous and isotropic must not be overlooked. Abusive use of the method has been made by geologists who have failed to recognize the fact that nature offers only few cases where the conductivity of the rocks may be assumed to be the same parallel and perpendicular to the bedding plane. Actually the ratio of the two resistivities in those directions may take values ranging from one (isotropic medium) to three for shales. In such conditions Tagg's method leads to disappointments. A method recently advocated by Manhart4 and Tattam6 forces Tagg's method to give a solution where manifestly the case under

Jan 1, 1934

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By Freeman Bishop

The House Ways and Means Committee recently heard a bitter dispute over whether gasoline with lead is a worse pollutant than gasoline without lead. The lead industry is also squarely in the middle of this dispute for obvious reasons. Lead used in gasoline amounts to 270,000 tpy, or more than 254 of the annual total mined in the U.S. Few industries can face the loss of such a market without wondering how they are to stay in business. The lead industry picked up unexpected support in this dispute, however, when the AFL-CIO stepped up with outright opposition to the President's proposal to tax lead in gasoline.

Jan 1, 1970

By Leo F. Reinartz

The history of steelmaking in the United States is a fascinating story of determination, sudden tragedy, exploitation, and inventive genius rolled into one gigantic plot. Mr. Reinartz' flowing interpretation of the progress made in the last one hundred years is being presented in a series of four articles. THIS is the Age of Steel. We live in a mechanized era. Our everyday lives--everything we see or do-are organized and influenced by this versatile metal. Our industries, our farms, our homes, and our transportation-yes, our vocations and avocations, or luxuries and necessities-all are dependent upon smelting iron and making steel. Take away iron and steel and soon our vaunted civilization would revert to a primitive existence. These metals, often in crude forms, have been known for thousands of years. Down through the ages, until about one hundred years ago, steel was made laboriously, and at high est, in small batches. During those years, methods of manufacture did not change very much. Over long periods of time only warriors, royalty, and wealthy people could afford to use articles made of iron or steel. History has recorded that the nations which were expert in iron and steel manufacture, and had access to rich iron-ore deposits, were the leaders in war or in peaceful pursuits. At the end of the 18th century, thirteen struggling American colonies had broken not only the political shackles that bound them to Great Britain, but also many of the economic bonds. They had showed their skill, Yankee ingenuity, and energy by making iron and steel articles for their own use. After the Revolutionary War, more and more hardy American pioneers pushed westward through the Allegheny Mountain passes and down the rivers into the fertile Ohio River and Kentucky country. Demands for articles made of iron increased. The iron industry on the east coast grew and prospered. As this trend continued, iron industrialists moved their plants westward to be near the large deposits of high-grade coal in western Pennsylvania, eastern Ohio, and nothern West Virginia. They also desired to use the local iron ores and water resources of those areas. Blast furnaces and ironworks were built in the Pittsburgh, Youngstown, southern Ohio, and northern West Virginia districts. In 1810, the United States produced 53,908 gross tons of cast iron and 917 tons of steel. Iron ore discovery A white man first discovered large deposits of iron ore in the northern Michigan and Lake Superior country in 1844. One year later, the Sault

Jan 1, 1961

By Ancel St. John

At the New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,' in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papcrs which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangc-mcnts were therefore made to present that evidence at this meeting. Material Examined The material exalllined was high-ernission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. Scope of the Investigation The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of t.horia detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

By W. A. Boyer

Edward Thomas (U.S. Bureau of Mines, Washington, D. C.)—This excellent article on an ingenious and successful installation of wooden rock bolts loses much of its effectiveness through an attempt by the authors to establish the general adaptability of this type of support. Possibly because they have only local experience as a guide, they imply erroneously in the first paragraph that the Bureau of Mines has been opposed to wooden bolting, although later in the article reference is made to a Bureau publication on the subject. In 1947 the Bureau of Mines decided to sponsor experiments in roof bolting in coal mines because the experience of the St. Joseph Lead Co. had indicated that this type of roof support appeared to be a roof-fall accident-prevention measure that might be adopted and also effect economies in operating cost. Justification for this belief has been borne out, particularly in coal mining. This program has been carried out under the following general program: 1—The Roof Control Section of the Bureau of Mines has advocated and initiated underground experiments under controlled conditions with many different ideas related to rock bolting since 1947. In no instance has cooperation in developing an idea been refused, no matter how ridiculous it may have seemed at first glance, if it has been requested by a mining company. 2—The Bureau of Mines has no police powers over the selection of roof-support devices and seeks none. 3—At the request of an operator, the Bureau of Mines will make comparative tests on various types of bolts underground and will submit resultant data for the operator's consideration. 4—Wherever possible, the Bureau publicizes successful installations, so that others may benefit from this experience; however, it is careful not to discriminate between manufacturers of bolts or bolt-installation equipment. Unsuccessful experiments probably should also be publicized, but from a practical standpoint it is usually not feasible. In other words, the role of the Roof Control Section of the Bureau is in line with the original purpose for which the Bureau was first organized: to serve industry through gathering, analyzing, and disseminating factual data. It would seem to be logical that the starting point for any experimentation on roof bolts in coal mines should be the time-proved practice of the

Jan 1, 1955

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

By K. J. Anusavice, R. T. DeHoff, H. Oikawa, J. J. Pinajian

STUDIES of nickel self-diffusion and impurity diffusion in pure metals and alloys have, for the past two decades, employed predominantly the nickel radio-However, because of the low energy of the emitted particle, careful and time-consuming techniques must be used to obtain reproducible measurements. In our studies of nickel diffusion into copper, we have recently used Ni66 [Td1/2: 55 hr; : 0.20 Mev (100 pet)] which decays to it much more suitable as a tracer because of the presence of the high-energy y radiation from the cu66 daughter. Although the half-life of Ni66 is appreciably shorter than that of Ni63, the useful working lifetime of a small quantity, " 10 mc, is about 1 month. preparation bf Ni66. he Nis6 radioisotope was produced at Oak Ridge National Laboratory by means of a double (n,y) reaction:

Jan 1, 1969

By Paul T. Allsman

Recently the U.S. Bureau of Mines completed organizational changes that, for the first time since the beginning of World War 11,. re-emphasize mining research as an important part of its responsibilities. A progress report follows on the Bureau's improved program for mining research. During World War II the Bureau's mining research lapsed in favor of short-range, more urgent activities. Since the end of the war mining has grad- ually returned to an economy where reduced costs and increased efficiency are essential to a vigorous industry, and demand for improvement through expanded research is again pre-eminent. In recognizing this situation, the Bureau is again emphasizing mining technology and has reinstituted some of its earlier mining research activities. Recent research, however, follows a more scientific approach in solving mining problems because new technology, particularly new instrumentation, has developed rapidly during the past decade.

Jan 7, 1960

By G. Adel, J. Richard Lucas, C. Haycocks

This paper describes over sixteen computer programs developed at Virginia Polytechnic Institute and State University during the past twenty years to assist in the design of coal operations. Overall development concepts in the construction of the programs are outlined, commencing with those used in the exploration phase of mining and extending through economic analysis and into the design of specific engineering systems such as belt, rail and power networks, scheduling, rock mechanics problems and simulation of face systems. Summarized information is given for the use of the major programs including user restrictions, input data, typical output and industrial applications and case studies. Analysis has been made of the programs' applications by industry throughout the world. Such analysis is facilitating development of new programs as well as a refinement of existing ones. To date programs have been constructed in four categories: exploration, ground control, economic and simulation. Face production simulations are stochastic in nature and require the use of time study data obtained at sites underground. Future programming efforts currently under development are aimed at interactive programs for use with minicomputers and, where advantageous, with graphical displays.

Jan 1, 1983

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By AIME

J. B. Haffner, or "Barney" as he is known to his wide circle of friends, was born at Landskrona, Sweden, on Christmas Day, 1886. He attended grade and preparatory schools there and then went to the Royal Technical Institute at Stockholm from which he graduated as a mining engineer in 1910. During these school years he gained practical experience in his summer vacations by working in various mines in Sweden and other European countries. Upon graduation he set forth for the land of opportunity, the United States. Upon arrival in this country he found people everywhere talking about the fabulous gold fields in Alaska and thereupon set sail for Nome, to take part in placer gold mining operations. Returning to the States, Barney worked in Illinois coal mines for a time and then carried on some construction work in Oklahoma. In 1913 he accepted employment with the Ray Consolidated Copper Co. in Arizona and soon found himself in positions of responsibility in the operating and

Jan 1, 1948

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By R. B. Lincoln

THE function of a pyrometer protecting tube is to maintain an atmosphere about the thermocouple most favorable to its continued accuracy and long life, and at the same time permit the weld of the couple to attain the full temperature of the area or object being measured. In addition to protecting the thermocouple from the chemical or alloying effects of the products of combustion or bath being measured, the tube must also protect the couple from mechanical injury. The conditions met in practice vary so much that no one material is suitable for all applications. The usefulness as well as the expense of maintenance of a pyrometer system are influenced greatly by a choice of the most suitable protecting tube. The tube must protect the couple without itself becoming too great an expense item. The protecting tube should have the following qualities: (1) A melting point well above the highest temperature to be encountered. (2) Sufficient strength through the entire range of temperatures to hold up its own weight and resist such shock and jar as are unavoidable. (3) It must be impervious to the atmosphere or bath to which it will be subject. (4) It must not give off any vapor injurious to the couple. (5) It must not form any oxides fusible below the highest temperature to be measured. The proper location of the tube in the furnace is almost as important as the choice of material. The tube must be placed as near to the work to be heated .as possible. It must be kept out of the direct path of flame, both because that would give too high temperature readings and because partly burned fuel will destroy the tube faster than the quiet products of combustion.

Jan 9, 1919

1. What Is a Rock Burst? . . . . 569 Jack Spalding . . 569 A. F. Robertson . 569 W. R. Crane . 569 G. S. Rice......569 P. J. Shenon........... 569 L. C. Graton........... 569 2. What Are the Causes of Rock Bursts? 573 Jack Spalding..........573 A. B. Yates and P. J. Shenon 574, 578, 592, 596 A. F. Robertson . . . . . 575, 595 W. R. Crane. ... 579 G. S. Rice.........582 Oscar Weiss .........582 P. B. Bucky..........582 P. H. Bird.....588, 592, 593, 595 M. K. Hubbert.........593 G. Wheeler.......... .593 B. F. Tillson........593, 595 T. T. Read............594 3. How Can Rock Bursts Be Prevented?. 597 Jack Spalding..........597 A. B. Yates and P. J. Shenon ... 598 A. F. Robertson.......599 W. R. Crane....... .602 G. S. Rice............602 Page 4. How Can Rock Bursts Be Predicted?. 602 Jack Spalding.........602 A. F. Robertson.......602, 603 A. B. Yates and P. J. Shenon ... 602 W. R. Crane......602 G. S. Rice......602 B. F. Tillson...........603 5. How Can Rock Bursts Be Controlled? 603 Jack Spalding..........603 A. F. Robertson.......603 W. R. Crane...........604 A. B. Yates and P. J. Shenon 604 Oscar Weiss........605 G. S. Rice......- 604, 609 R.D.Hoffman..609, 610 R. D. Hall..........609 R. H. Cromwell . . 609 P. J. Shenon...........609 P. B. Bucky......609, 611 B. F. Tillson.........609, 611 A. B. Yates...610, 611 P. H. Bird.......610 6. General Discussion........ 611 Jack Spalding.......... 611 R. D. Parker....... . 616 C. Baring Horwood........ 618 P. B. Bucky........... 619 Foreword This symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge, which, if successfully met and overcome,

Jan 1, 1946

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972