Search Documents

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By T. N. Rhodin

There can be two types of films on solids, those which are stable in mono-layers and those which tend to aggregate into three dimensional structures. A great number of metal films formed by condensation onto a solid base are unstable in the sense that they will aggregate into crystals providing the atoms possess sufficient surface mobility. The crystalline structure of the film is strongly influenced by the base in many systems and, in some cases, a single orientation prevails when the force fields around the atoms in the supporting crystal are sufficiently strong.' Relatively little is available in the literature about the nature of these forces and the role they play in promoting a preferred orientation of the atoms arriving at the substrate surface. An understanding of their periodicity and magnitude relative to the surface forces characteristic of the film itself should provide insight into the critical dependence of film orientation on the nature and temperature of the substrate. In addition, this effect may be very useful in preparing samples for surface studies. The study of the physical and chemical characteristics of pure metal surfaces has been severely handicapped by the presence of strongly adherent foreign films. Furthermore, the randomness of the surface orientation has obscured interpretation of experimental results. Evaporation of metals in high vacuum onto carefully selected substrates under ideal conditions for preferred orientation appears suited to the preparation of flat, oxide-free, oriented films for surface reaction studies. Many factors influence their structure and some understanding of the mechanism of their formation is a necessary prerequisite for obtaining satisfactory surfaces for study. The dominant factors in defining film structure are film thickness and growth rate and the nature, condition, and temperature of the substrate. GENERAL ASSEMBLY The system was enclosed in an 18 in. bell jar which rested on an L-shaped neoprene gasket on a ground steel plate as indicated in Fig 1. Rapid evacuation of the system to 10-6 mm mercury was facilitated by a 4 in. manifold, 2 in. packless valve, and an extra large diffusion pump. Suitable arrangement of valves on a secondary manifold readily permitted introduction of purified gases

Jan 1, 1950

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood' suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener's mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh's5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

By A. J. Brown

I herewith send to the Institute a sample of Pancake coal. It is rather early yet to make any estimate of the future value of the discovery; but it is certainly the most promising vein of coal yet discovered in the State of Nevada, and, I believe, the first true coal found west of the Rocky Mountains, or perhaps west of the Missouri River, unless some of the Utah coals belong to the coal measures of the Carboniferous age. The Pancake vein certainly belongs * Since the above paper was read before the Institute, some modifications in the description of the machine have been made in order that recent improvements may be embraced.—U. S. A.

By S. G. Cupschalk, J. J. Wert, R. A. Buchanan

The uniaxial deformation of thermally ordered and disordered polycrystalline Cu3Pt was studied by means of the X-ray line - broadening analysis according to Warren and Averbach and the extension of this analysis to ordered fcc materials by Mikkola and Cohen. Because of the heat treatment history, extinction had a pronounced effect on the X-ray spectra of ordered and disordered C%Pt at small plastic strains. After an appropriate correction for extinction, the long-range order in thermally ordered ChPt was found to decrease at a slow constant rate with plastic strain. Furthermore, the antiphase domain probability increased at a constant rate to 17.5 pct strain. The effective particle size behavior indicated that the stacking fault energy is lower in ordered than in disordered Cu3Pt. Analysis of the stress-strain curves shouled that ordered Cuzt has a slightly lower yield Point but a much higher work-hardening rate than disordered Cu3Pt. THE presence of long-range order in a solid-solution alloy has a marked effect on its mechanical properties. While this effect has been known qualitatively for many years, it was not until recently that detailed investigations have been performed to determine the exact role long-range order plays in this strengthening mechanism. The development of an advanced, quantitative. X-ray diffraction analysis by Warren and Averbachl and the extension of this analysis to the L1, type super lattice by Mikkola and cohen2 have greatly accelerated research in this field. The research reported in this paper consisted of two primary phases. The first phase was to determine the effect of long-range order on the tensile properties of polycrystalline Cu3Pt. This objective was accomplished by comparing the stress-strain behavior of thermally ordered CusPt to that of thermally disordered CusPt. The second phase of the research was to determine the difference between the atomic arrangements in thermally ordered and thermally disordered Cu3Pt as a function of uniaxial deformation and thereby gain a deeper insight into the mechanism by which long-range order affects the tensile properties. This second objective was accomplished by applying the Warren-Averbach method of peak profile analysis to the X-ray diffraction patterns obtained from ordered and disordered Cu3Pt after given amounts of uniaxial deformation. EXPERIMENTAL PROCEDURE The Cu3Pt was prepared by vacuum melting and casting. After a homogenization anneal, the ingot was cold-rolled to sheet form. Two tensile specimens with gage sections of 2.50 by 0.500 by 0.115 in. were carefully machined from the sheet. The specimens were polished with a final step of 600-grit paper to insure smooth diffracting surfaces. Finally, one specimen was heat-treated to yield an average grain diameter of 0.016 mm and an initial degree of long-range order, S, of 0.825. The other specimen was water-quenched from above the critical temperature, 645"C, to yield an average grain diameter of 0.017 mm and zero long-range order. The heat treatment history of each specimen is shown in Table I. The tensile tests were performed utilizing a Research Incorporated Model 900.95 Materials Testing System. This unit employs a closed-loop feedback system which maintains a constant strain rate through an extensometer clipped to the gage section of the tensile specimen. A strain rate of 1.32 i0.02 x 10"4 sec-' was employed in testing both specimens. In the X-ray diffraction analysis, a General Electric XRD-5 diffractometer equipped with a pulse-height analyzer set for 90 pct efficiency was employed. The goniometer speed selected was 0.2 deg, 20, per min. Filtered Cu radiation was used for all peaks and all peaks were chart-recorded. Because of nonuni-form grain size. it was necessary to spin the specimens during X-ray analysis in order to obtain reproducible integrated intensities. The spinning rate was 2000 i100 rpm. The application of the Warren-Averbach method of peak broadening analysis to a diffraction pattern is very time consuming if done manually. In this research, the calculations involved were performed with the aid of a computer program by wagner.3 As reported by Wagner, the program is written in Fortran TV computer language. It was modified to Fortran I1 so as to be handled by the IBM 7072 computer at Van-derbilt University. In the X-ray diffraction analysis of uniaxially deformed Cu3Pt, the 100, 200. 400. 111, and 222 reflections were recorded from the initially ordered sample after 'plastic strains of 3.0, 6.0, 9.0, 12.0,

Jan 1, 1970

By J. Parker

As a practicing mining engineer, I face many rock mechanics' problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert's suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast's results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground. are often at least as large as the vertical stresses. Visual observation of the deformation of roof and pillars (including failure due to horizontal compres- sion) also demonstrates that the horizontal stresses are often most important: Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic.

Jan 1, 1967

J. D. Fast and J. L. Meijering (Philips Research Laboratories, N. V. Philips' Gloeilampenfabrieken, Eindhoven, Netherlands)— After the departure of our friend Dijkstra to the United States, investigations on the effect of alloying elements on the behavior of nitrogen in a iron were continued in Eindhoven. We too found internal friction curves with two separate peaks for iron containing nitrogen in addition to 0.5 atomic pct V or 0.5 atomic pct Mo. Our first publication on these investigations" appeared almost simultaneously with the paper now under discussion. At first sight our experimental results seem to be in harmony with their conclusions, but a closer examination reveals that in the case of the Fe-V-N alloy the abnormal peak is not controlled by one time of relaxation only. Whereas iron containing 0.5 atomic pct Mn or Mo absorbs an amount of nitrogen of about the same magnitude as that absorbed by pure iron under identical conditions, iron containing vanadium absorbs in addition one nitrogen atom for every vanadium atom. This last amount, far exceeding the first amount in the case under consideration, combines chemically with the vanadium and causes no internal friction. The "free" nitrogen in the vanadium alloy gives rise not only to a damping peak corresponding to that in pure iron but— due to the presence of VN particles in the metal—also to the abnormal peak at higher temperatures. The VN particles create interstitial sites around themselves where the free nitrogen atoms are bound much tighter than in the normal interstices. These abnormal interstices, therefore, will capture free nitrogen atoms rapidly, whereupon these give rise to the abnormal damping. The binding energy in the abnormal interstices is not the same for all, and with coarsening of the VN precipitate the distribution of these energies is displaced toward the side of stronger binding. This is deduced from a shift of the summit of the second peak toward higher temperatures (from 80" to 88°C in our experiments) caused by prolonged heating at 950°C. From the intermediate state where they cause the abnormal damping, the nitrogen atoms pass over rather rapidly into the fully precipitated state (iron

Jan 1, 1954

By C. C. McDermond, Others, B. N. Zavoico

Production of crude oil in Venezuela for the year 1937 was 186,653,-916 bbl., as compared with 155,228,982 bbl. produced in 1936, an increase of almost 31,500,000 bbl. The oil-field strike, which started on Dec. 14, 1936, lasted until Jan. 25, 1937, when a total of 10,000,000 bbl. of production was estimated to have been lost (5,750,000 bbl. in 1936 and the remainder in 1937). Of the total of 186,653,916 bbl. produced in 1937, the Lagunillas field contributed 45.6 per cent, a drop of approximately 10 per cent under 1936 figures; Tia Juana, 14.3 per cent; Quiriquire field, 14.0 per cent; La Rosa area, 13.3 per cent and the Mene Grande field, 7.6 per cent, these being the five leading contributors of the year's production. Detailed production figures by fields and by companies are shown on Table 1. Of the total production of Venezuela the following four major companies accounted for the greater proportion: Standard of Venezuela and Lago Petroleum Corporation together, 48.3 per cent; Shell, 37.4 per cent and Venezuela Gulf, 14.0 per cent. At the end of the year, 2491 wells were producing, of which number 1291 wells were pumpers, or about 52 per cent. Production The accompanying statistics of production record of Venezuela oil fields from its inception to Dec. 31, 1937, shown on Table 2, indicates that the cumulative production reached 1,503,283,228 bbl. In order of importance, Lagunillas leads all the fields, having accounted for about 50 per cent of Venezuelan production, followed by La Rosa area, which produced about 21 per cent; Mene Grande, which produced about 13 per cent, and Quiriquire, which produced 6.5 per cent. Table 3 shows the age of each field. Mene Grande is the oldest, having produced for 24 years; Tarra is next, 21 1/2 years old, and El Mene third, 171/2 years. The gravity of the crude from the various fields, also shown on Table 3, remained unchanged, the only addition being the new Tia Juana field, which averages 15.6' A.P.I. Table 4 shows the method of production by fields as of Jan. 1, 1938; at the end of the year 2491 wells were producing, compared with 2005 wells producing at the beginning of 1937, or an increase of 486 wells. The completions for the year reached 512. Of the 2491 wells producing crude oil, 1291 wells, or approximately 52 per cent, were pumping, 925 (approximately 37 per cent) were flowing naturally and 275 (11 per cent) were on

Jan 1, 1938

By Walter Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphi-cal determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the litera-ture. In this paper, for simplification of exposition, the change in pres-sure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of cal-culating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small-scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would he used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute.

Jan 1, 1938

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936

By Alden B. Greninger

Twinned metal crystals are usually designated as either deformation twins or annealing twins. If twins are to be classified according to the treatment the metal has undergone just prior to the observation of the twins, there are two other possible groups: (1) solidification twins,† when observed in the as-solidified or as-cast condition, and (2) transformation twins,† when observed in a metal which has been cooled from above an allotropic transformation temperature. McKeehan has demonstrated that ferrite does, occasionally at least, contain twinned structures2. The twins, which he studied by optical methods, were obtained during the preparation of iron single crystals by very slow cooling through A3. He proved that the twin relation was actually that which previous investigators had predicted; namely, twinning along three planes of the form (112). Since McKeehan's discovery, little or no attention has been given to this transformation twinning of alpha iron, or to the possibility that it might occur at all speeds of cooling from above A3 instead of merely during the preparation of single crystals. McKeehan's twins were evidently regarded as interesting only in proving that a body-centered cubic metal could form twinned structures—at least under certain conditions. It is generally believed that iron seldom if ever forms annealing twins. Certainly the straight-line banding which is so abundant in annealed face-centered cubic metals is characteristically absent in iron annealed below A3. However, O'Neil13 has studied "twin-like" crystals in annealed alpha iron and concludes that the specimen he studied actually contailled a few annealing twins. Tamura4 as reported "twin-like" crystals both in wrought iron and mild steel; specimens of the latter were annealed above and below A3 and showed "twin-like" crystals after both kinds of treatments.

Jan 1, 1936

Jan 1, 1935

Carlisle: This is April 19, 1961. My good friend Dave Irwin is sitting on the other side of the tape recorder. We are at Rose Dhu Island, Savannah, Ga. Now, let's begin with your first job, where and what was that? Irwin: I started out to Arizona, looking for a job and wound up in Morenci. The next morning I applied at the mine office and was put on as a sampler. I worked as a sampler and as an assistant to Frank Pelton, the geologist, for a year, after which I went back to New Haven to take my last year of postgraduate work. After getting my degree, I went back to the Southwest with W. Rowland Cox and Staff, supposedly as a geologist. Q: But that was not when he was with Spurr? Irwin: That was after he had left Spurr. Henry Smith was with the Spurr end of the outfit and I happened to drop into the W. Rowland Cox end. My first job with him was to do some work on a prospect above Metcalf, Ariz., and from there I would go out on short reconnaissance trips in Arizona, New Mexico and old Mexico.

Jan 6, 1964

By L. G. Huntley

THE only oil produced in Colombia during the past year has been that from the Tropical Oil Co. concession, operated by the International Petroleum Co. This has been about the same in amount as that of 1923, or approximately half a-million barrels gross, which has been used to supply the domestic requirements of the republic and for the company's own use, in about equal proportions. The Tropical Oil Co.'s field at Infantas has 17 producing wells, for the most part shut in. The company claims an average initial production of about 1000 bbl. each for these wells, which would represent a total potential production of 10,000 bbl. However, the area already outlined by this work is considerable, as drilling has apparently been carried on with the idea in mind of blocking out the field, rather than developing the greatest possible production. Therefore, whether or not the pipeline of the Andian National Corpn. is being built to take care of the amount of crude production admitted by the Tropical Oil Co., or a greater prospective amount, it is certain that this production could be quickly increased if desired.

Jan 3, 1925

By J. M. Johns

INTRODUCTION The Climax Mine is located on the continen¬tal divide, on Fremont Pass, about 145 Km south west of Denver, Colorado. Molybdenum, along with the by products, tungsten, tin, and pyrite are produced from both the open pit and under¬ground operations. The underground operation utilizes a panel caving mining system, and produces in excess of 27,000 mt per day. In the mid 1930's, the Climax mine began changing from a grizzly level layout to the slusher drift system which is still in use to¬ day. Over the years, the slusher drift layout has been refined to correct, improve, and sim¬plify minor operational problems. In common with most older hardrock mines, the development equipment used at Climax was the standard rail mounted, pneumatic mining machinery. This type of equipment remained in use, at least to some degree, until about four years ago. For production, 112 Kw electric slushers were used, while mine traffic was rail with trolley locomotives. Beginning about ten years ago, Climax began

Jan 1, 1981

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

THE solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels from well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approximately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and after some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sections are easily reworked, (4) low cost. CONSTRUCTION It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following procedure for those who contemplate the construction of such a model: I. Determination of the Scale.-Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to be used. 2. Construction of the Base.-A satisfactory base may be constructed by using two pieces of three-ply wood separated by strips of i by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Construction of the Frame (Fig. I).-In the construction of the frame the use of 1/2-in. o.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least I in. higher than the

Jan 1, 1941

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By H. Biloni

A metallographic study of solute segregation produced during controlled solidification of Sn-Pb alloys has previously been reported.' It was found that the growth conditions which produced well-developed cellular substructures led to severe segregation, and even at solute concentrations of 0.2 wt pct Pb regions of a lead-rich phase were formed at the junctions of cell boundaries (nodes). Similar sample preparation and etching techniques have now been applied to several tin alloys at more dilute concentrations. The crystals were solidified uni-directionally under less-severe growth conditions so that the predominant interface structure was composed of two-dimensional cells.* Binary alloys with lead, using 9.999 pct Sn as a solvent, and ternary alloys with lead and bismuth or lead and antimony, using zone-refined tin as a solvent, were examined. The liquid was decanted from the growing crystals in all cases to reveal the interface structure and ensure that two-dimensional cells were being formed. However, since interference may arise from a liquid layer that clings to the interface during decanting,3 an examination of the segregation pattern was always made behind the interface. In all cases, the structure within the bulk of a crystal at greater than 1 cm behind the decanted interface was substantially the same as that nearer the interface. Representative photomicrographs of the dilute Sn-Pb alloy are shown in Figs. 1, 2, and 3. Most observations are similar to those of the previous investigation. For example, the solute concentration at the cell walls is higher than in the intercellular regions; where cell boundaries meet, the segregation is enhanced; the macromosaic or stria-tion substructure and grain boundaries show enhanced segregation; there is also a depletion of solute at cell walls near a striation boundary, as Spittle et a1.4 have observed at decanted interfaces. Not all these observations can be seen in the photos shown since attention has been focused on a special feature; as evident in the photomicrographs, cer-

Jan 1, 1965

By Edgar L. Collis

NO industry or group of industries is more deeply interested in the influence exerted by atmospheric dust than that concerned with the getting of coal and of metalliferous ores. The coal miner in the past has mainly been interested on account of the part played by coal dust in the occurrence of explosions; but investigation is revealing that coal miners experience, at least on certain coal fields, unduly high mortality ascribed to lung diseases, some part of which may reasonably be attributed to dust inhalation, and that a small group of men employed in sinking shafts and driving roads through sandstone rocks experience troubles identical with those that afflict many metalliferous miners. Coal Mining The Registrar General for England and Wales issues information every 10 years concerning the mortality experienced in various industries. The records dealing with coal mining are of particular interest, since they are given separately for each of the largest fields. When examined they exhibit the coal miner with a favorable death rate on the whole when compared with all other occupied males; but they reveal great differences on the different fields; thus the Lancashire miner in 1900-2 had a comparative mortality from all causes of 1006 as against a figure of 675 for the Nottinghamshire and Derbyshire miners, and in 1910-12 of 941 as against 570 for Nottinghamshire. When mortalities due to four only of the great causes of death are subtracted from the total the differences are greatly reduced; these four causes are phthisis, pneumonia, bronchitis and accidents. Thus for 1910-12 more than one-half of the mortality in Lancashire, 478 out of 941, is so accounted for, but less than one-third of the mortality in Nottinghamshire, 184 out of 570; the latter fraction compares with that for all males, 293 out of 790. Exactly why the accident mortality varies thus with those for the lung diseases has not been determined; the fact, however, points to an interesting association between health and so-called "accidental" occurrences.

Jan 1, 1927

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983