Search Documents

By Harold Powers

THIS paper presents geophysical and subsurface data observed in the vicinity of Shafts No. 1 and and 5 of the National Lead Co. lead mines at Fredericktown, Madison County, Missouri, see Fig. 1. The area selected is an excellent example to illustrate the close correlation between geophysical data and geological facts as revealed by drilling and mining. Such close correlations make geophysical applications appropriate to the development of known ore-bodies as well as the exploration for new orebodies.

Jan 3, 1953

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By Henry Leidheiser, Melvin C. Jr. Hobson

The rate of formation of the intermetallic compound, indium antimonide, at the interface between iudium and antimony at 100°C is greatly increased when a composite electrode of indium electrode -posited on antimony is made the cathode in an electrolytic cell. The amount of indium antimonide formed during electrolytic treatment at constant potential appeared to he proportional to the square root of time, but the scatter of the data, particularly at long times, makes it impossible to state this conclzlsi1:ely. The rate constant for the electrochemical synthesis was estimated to he 1.5 x 10-12 sq cm per sec. A similar- set of experiments was conducted in the absence of an applied potential but under otherwise similar conditions. The rate constant lor the thermal synthesis was less than 2 x 10-14 sq cm per, sec, at least two orders of magnitude less than obtained during electrolytic treatment. In a series of electrochemical studies it was observed that intermetallic compounds formed on the surface of polarized electrodes.1'2 The possibility of using this technique for the electrochemical preparation of intermetallic compounds was investigated and subsequently applied to the synthesis of the semiconducting III-V compounds. Gallium antimonide, indium arsenide. indium antimonide, and indium bismuthide were successfully formed by electrodepositing the Group III element from a boiling acid solution onto an electrode made of the Group V element. The following kinetic studies were undertaken on indium antimonide to obtain quantitative information on the rate of formation of this representative III-V compound under a potential gradient. EXPERIMENTAL The electrolytic cell for these experiments was a modified, three-neck, round-bottom, 500-ml distillation flask. Sealed into the side of the flask was a Luggin probe which monitored the surface of the working electrode and extended out of the flask to a small reservoir containing a saturated calomel electrode. The counter electrode was platinum. The three electrodes were connected to a Wenking po-tentiostat which maintained a preselected constant potential near the surface of the working electrode with reference to a saturated calomel electrode. All potentials noted in this paper are with reference to a saturated calomel electrode at 45° ± 5°C. The potential and the current were both monitored using Sargent Model MR recorders. The antimony electrodes were cast in graphite molds to form spheres about 15 mm in diameter with a shank 6 mm in diameter and 10 mm long. A heavy copper wire (12B & S gage) was soldered to this shank. Collodion was applied for protection to the shank and the connecting part of the copper lead. A snug-fitting O-ring was slipped over the shank and the electrode was then fitted into a teflon holder such that only the spherical portion was exposed. The electrode surfaces were cleaned and chemically polished prior to assembly and introduction into the electrolyte by etching in a modified CP-4 solution (50 parts glacial acetic acid, 10 parts concentrated nitric acid, 2 parts 48 pct hydrofluoric acid). The electrolyte was 10-2 M In+3 in 1 MH2So4 and its temperature was held constant by refluxing. The reflux condenser was open to the atmosphere and no temperature correction was made for changes in barometric pressure. The indium concentration in the electrolyte was checked from time to time by the analytical method outlined below for the determination of the amount of indium antimonide formed electrochemically. A schematic of the recorded potential is shown in Fig. 1. At point A the antimony electrode was introduced into the cell and the open-circuit potential recorded. At point B the potentiostat, preset at the desired potential, was switched on. It was switched off at point C and the potential fell to the open-circuit value of the electrodeposited indium. The

Jan 1, 1965

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

Would you briefly describe how you chose the minerals industry and reflect upon some of your earliest experiences? I wish that I could say that I had a well-formulated career plan early in life and that mining engineering was always foremost in it, but I cannot, In fact, I was quite indecisive before I finally chose my life's vocation. But in another respect, I am glad my career unfolded in the manner it did because it gave me a better insight into advising others on career opportunities. Probably the greatest problem confronting our youth, and the one I find preys upon their minds the most, is their inability to select a career path early in life. This indecision frequently has a deep psychological effect upon them and they become down on themselves. Therefore, it fortifies them somewhat to learn that others who have become successful in their careers had difficulties choosing a career path early in life. However, while assuring young people that an early choice is not absolutely essential for success, I caution them to work toward as early a decision as possible.

Jan 3, 1979

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By David P. Hale, Guy W. Jordan

HIGH-IRON cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to freezing and thawing, and increases the resistance of the cement to sea or sulphate waters. During the past few years the construction of numerous dams throughout the Southeast by the Tennessee Valley Authority has stimulated the production of high-iron cements. At present a great number of specifications call for an iron cement, and the industry is supplying this demand with a Portland cement carrying approximately 5 per cent iron oxide. Several manufacturers are now making practically all of their cement of this type and a number of others manufacture it as a special cement over short periods to meet demands from the Tennessee Valley Authority and other buyers. The recent increase in the use of iron in Portland cement has created a market for iron products that previously was nonexistent. The chief sources of supply for the cement manufacturers at present are iron sand, iron sinter and slag, and ocher. The Copperhill mining district, Tennessee, supplies both iron sinter and slag for use in cement. The Cartersville district supplies iron sand, ocher, and some iron resulting from the magnetic separation of iron from barite. The advantages of these products vary according to the chemical properties of the raw materials and the methods of handling used by the different manufacturers. Where the iron is to be handled by conveying belts and in hopper cars, the iron

Jan 1, 1939

By D. R. Hay, E. Scala

STUDIES of structure-sensitive properties, especially mechanical behavior, have shown that grain and subgrain structure play an important role. The mechanical properties of tungsten, in particular, are sensitive to the nature of the intergranular structure. Substructure and dislocation networks in single-crystal and polycrystalline tungsten have been studied by Nakayama et al.' Various orders of substructure were observed ranging from a microscopic first order (grain diameter: 2 to 8 mm) to a microscopic second order (grain diameter: 50 to 300 p), and, within the latter, dislocation networks forming an even smaller order of substructure. In their single crystals, grown by arc fusion, the degree of misorientation in each order was small: 16'3OU, -11, and -10" for the first-, second-, and third-order substructure, respectively. To study the properties of polycrystalline tungsten, powder metallurgy tungsten is generally used. However, in a mechanical property investigation, the zone-melted or arc-fusion crystals are more desirable than the powder metallurgy product due to their higher purity and absence of porosity and other defects inherent in consolidation by powder metallurgy. Grain boundaries can also be produced in melted stock by working and recrystallizing. However, material with subgrain mis orientations of the order of several degrees (high-angle substructure) has not been reported previously and is the subject of this communication. Crystals were grown by electron-beam, floating-zone melting. The starting material, Sylvania Pure-tung welding rod, was given one zone pass at a traversal rate of -2 mm per min. Through control of the zone temperature, it was possible to influence the degree of crystal perfection. By maintaining the zone at a high degree of superheat, high-perfection crystals could be grown. However, at temperatures only slightly above the melting point, the zone-melted crystals contained a high-angle substructure. A sensitive control of the zone temperature was not possible due to the difficulty of estimating the temperature of the zone and of providing a constant supply of power to the sample. Therefore, an empirical method, using the shape of the molten zone as a criterion, was adopted as an indication of temperature. At high degrees of superheat, the surface tension of the molten zone decreases and a neck forms at the top of the zone, whereas at low zone temperatures the diameter of the zone remains reasonably uniform. Although it was not possible to obtain a continuous variation of misfit angle, the conditions could be directed toward the growth of either high- or low-angle substructure by maintaining only a slight neck in the zone (sufficient to establish that it was molten) or a well-necked zone, respectively. Mass spectrographic analyses of both types of material revealed no significant differences in the concentrations of their impurities. The degree of misorientation at high angles was obtained by measuring the angular spread of spots corresponding to a single reflection on a Laue back-reflection photograph. Fig. 1 shows a typical Laue back-reflection photograph of a crystal with a 3-deg spread. By measuring the angular deviation of the spots corresponding to a single reflection from the mean center of the spots around which constant angular deviation contours were drawn, an average angular spread of misfit could be calculated. The angular average was weighted by the number of spots observed in each angular interval. At angles greater than 5 to 6 deg the spots from different reflections begin to overlap, and cannot be associated with a particular reflection. Laue back-reflection photographs taken at different locations on samples .with approximately 3-deg spreads showed only a small difference in angular misorientation, less than 8' of arc, within individual specimens. The microstructure was examined using Berg-Barrett X-ray extinction contrast microscopy. Berg-Barrett photographs taken directly on the as-grown surface, Fig. 2, show an essentially equiaxed subgrain structure of -0.1 mm in average grain diameter in both high- and low-angle crystals. Fig. 2(a) is a photograph of a sample with a low misfit angle and Fig.

Jan 1, 1968

By George W. Goetz

As is well known, the general use of natural gas in Pittsburgh and vicinity for domestic and industrial purposes has shown the great advantages and benefits to be derived by the use of a gaseous fuel. In order to ascertain and bring together all the facts relating to a large and economical production, purification, distribution, and consumption of fuel-gas made out of coal, the Fuel-Gas and Electric Engineering Company, Ltd., was organized, under the presidency of George westinghouse, Jr.

Jan 1, 1890

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

The solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels irom well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approxi-mately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and aiter some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sec-tions are easily reworked, (4) low cost. Construction It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following pro-cedure for those who contemplate the construction of such a model: 1. Determilzatiolz of the Scale.—Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to he used. 2. Construction of the Base.—A satisfac-tory base may be constructed by using two pieces of three-ply wood separated by strips of I by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Constructiolt of the Frame (Fig. I).—In the construction of the frame the use of %-in. 0.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least r in. higher than the

Jan 1, 1941

By G. Sachs, L. J. Ebert, W. F. Brown

INTRODUCTION ISOTHERMAL transformation, or "austempering," of a carbon-containing austenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.1 Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4-5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.6-7 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels.8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140). The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1948

By F. R. Hensel

The present study was made to determine the laws governing the formation of the primary? crystal structure during solidification. Most of the experiments were carried out on chill castings, but from the resiilts it will be possible to draw certain conclusions as far as sand castings are concerned. It is necessary to discuss first a number of theories, which are generally adopted for explaining the structure of an ingot. Usually, the structure of an ingot consists of the following three zones (Fig. 1): (1) a chill layer of small at-random oriented crystals; (2) a layer of columnar crystals; (3) a zone of equiaxed crystals. The tensile properties of the chill layer and the equiaxed range are usually much better than in the columnar range, particularly the planes that are formed by the columnar crystals growing from two sides at right angles have low tensile properties. This is one of the reasons why columnar crystals in ingot structures are undesirable.

Jan 1, 1937

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By T. M. Williams

DURING the year just ended we have had three great fires in the mines in the Wilkes-Barre district. One at the Empire Colliery, one at the Prospect shaft, and the other at the Baltimore old mine. It is proposed in this paper to give a brief history of the fire at the Empire Colliery, and the methods employed in extinguishing it. The fire was first discovered breaking out in the air-stack, alongside what is known as the " Kidder Plane," about one o&apos;clock on the morning of December 31st, 1873. Subsequently it was ascertained that the fire originated in the return airway somewhere near the steam boiler, located inside the mine, near the head of No. 5 slope. The coal from this slope was hoisted to the shaft gangway, at a point nearly four thousand feet distant from the foot of the shaft. As there were from four to five hundred mine cars hoisted per day from this slope the steam boilers were located at this place. The mines being of considerable extent required a large volume of pure air for ventilation, and no fan having been erected at this slope at the time, the heat from the boiler was made use of to assist ventilation, by conveying the return air from No. 5 slope into the large airway made from these boilers to the surface through the old "Kidder slope" to the stack where the fire was first discovered. The length of this slope or airway was about one thousand feet, with a sectional area of about sixty feet. The quantity of air passing through it must have been over sixty thousand cubic feet per minute

Jan 1, 1875

By Henry J. Welge

Laboortory apparatus has been devised which permits study of the displacement of oil from cores by water and by gas. The cores used contained interstitial brine as well as oil. Experiments were run to determine the comparative effect of varying the properties of the fluids used. No great effect was noted on the maximum displacement achieved. This observation made it unnecessary in initial work to use fluids in their exact reservoir conditions. Consequently, the displacements were run at near-atmospheric pressure in Pyrex glass equipment, using stripped crude oils. Introduction and Theory The chief object of this work has been to determine the efficiency of gas and water as primary agents for displacing oil from reservoir rock under laboratory conditions in which capillary phenomena were predominant. To this end the maximum displacement of oil from cores has been ascertained. This maximum displacement may not be equal to the maximum displacement from a reservoir; but it will be a close approxirnation to it sometimes, and other times the laboratory information will be useful in reservoir engineering predictions. It is] believed that the laboratory experimental maximum represents the upper limit for the reservoir recovery. The experiments were carried out by obtaining cores of interest from the reservoir, and filling the pores with interstitial brine and oil with the restored state tech- nique.1 Then the oil was displaced from the core as described later, either by brine from below, or by gas from above. The former type of displacement suggests analogy to production by water drive, but not to water flooding, for reasons discussed below. The latter type of displacement is believed to simulate production by gas cap displacement. The displacements were performed by what may be termed the capillary-pressure method. The cores are placed in capillary contact with an oil-wetted membrane which has very small pores (about I micron in diameter). Pores of this size will transmit oil but Prevent the Passage of gas or water, unless the Pressures used are higher than the capillary Pressures employed in this work. Accordingly, use of the membrane makes it possible to apply a capillary pressure differential between the displacing phase and the oil in the core. AS in the displacement of brine toward that condition of oil and water distribution existing originally in the reservoir,&apos; it may not always be desirable to reduce the oil saturation in this experiment to an absolute minimum. With reservoirs having small productive closure, it is preferable to evaluate and use a displacing pressure no higher than the capillary pressure, Ap, which will ultimately become available for displacement in the reservoir. This pressure may be calculated from a knowledge of the density of the oil-in-place, do, the density of the displacing phase, dl, and Ah, the vertical distance between the section of the

Jan 1, 1949

By M. D. Hassiallis

The claim is made in a number of patents1&apos;2&apos;3&apos;4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S2-R&apos; (where x = 1,2, . . . ), with the restriction that if the aromatic radicals R, R&apos; contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using diphenyl sulphide, ditolyl disulphide and dinapthyl disul-phide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed. was that of Moses, Hess, and Perkins. A sample of ore weighing 500 • grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65-mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a a-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8:I. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of I2:I. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. Contact-angle Tests In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcodte, chalco-pyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R&apos; contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943