Search Documents

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By E. Topuz, G. Faulkner, M. Karmis, C. Haycocks

The Appalachian coal region of Virginia, southern West Virginia and Kentucky and the extreme eastern portion of Tennessee constitutes a unique area of surface coal mining activities. The area contains a number of contiguously placed coal seams, up to a total of fourteen in some places, which vary in thickness from a few centimeters to 2,5 meters. Much of this coal is of high quality, some being the highest grade metallurgical coal found anywhere in the world. The region may be broadly characterized physiologically as a dissected plateau with a relief above the valley floors of up to 500 meters and a dendritic drainage pattern. Up to six seams may outcrop in the hillsides above drainage, many of which have been subjected to contour stripping operations. Prior to the passage of the surface mining reclamation act, little effort was made to reclaim stripped areas. The passage of the strip mining act, including the controversial requirement for returning the land to its approximate original contour, has forced intensive recla¬mation efforts from the mining industry. The wisdom of this original contour requirement has been the subject of considerable debate and litigation, mainly because of its cost, inconvenience, and value of the land after it has been reclaimed. Regardless of whether recla¬mation is carried out, under current practices slope failures do occur. This in effect circumvents the intent of the law and can expose large unvegetated spoil areas, and contribute to hillside erosion and stream silting. Such failures must be eliminated if further costly reclamation efforts are to be avoided.

Jan 1, 1983

By Ernest M. Spokes, Martin A. Thieme

A simulation model developed to analyze scraper-pusher utilization in open pit mining systems is described. The mining simulator discussed was developed as a tool to aid management in evaluating alternative open pit haulage schemes and to reduce the risk involved in the selection of equipment.

Jan 1, 1973

The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the 11on and Steel Division. The following mere the Howe lectures and lectures for the years indicated: 1924 What, is Steel? By Albert Sauveu

Jan 1, 1944

By AIME AIME

IN RESPONSE to a request from the president- elect of the Institution of Civil Engineers of Great Britain, Mr. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, prepared a brief history of the joint activities of engineering societies in the United States, from which we have taken the following facts. National Societies Our first joint activities were in collection with the celebration of the eightieth birthday of "Uncle John" Fritz in 1902, and it is of interest to note that two of the members of the original celebration committee, Messrk. . Ambrose Swasey and Jesse Merrick Smith, will be members of the official deputation to England in June. Mr. Rice, also,' was .a member, of the original committee.

Jan 1, 1921

The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and out standing attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur.

Jan 1, 1934

By Paul Soros

The cost of shipping British coal by water to domestic and ex- port users has been expensive. The traditional transportation system functioned as follows: coal in up to 50 different grades was accumulated in railway cars at several loading ports; on the arrival of a vessel, cars were dumped in the desired order to produce the required blend. It was a direct rail- road-to-water interface. Railroad freight was high because of the poor utilization of the large number of small (14, 18 or maximum 28-ton capacity) hopper cars required. Ocean freight was high because the ships were small, mostly on the order of 1500-3000 dwt and even these took a long time to load. Assembling and loading larger cargo presented a challenge in logistics to the ports, the railways and the coal washeries. The accommodation of larger bulk carriers was hampered by a tidal range of up to 24 ft which led to the development of impounded harbors, with locks that limit the size of vessels.

Jan 12, 1973

By C. W. Ryan

THIS paper contains a brief sketch of the geology of soapstone in the Piedmont section of Virginia, in the southern portion of Nelson County; also a description of methods of prospecting, developing quarries, quarrying and and milling methods in that section. The paper is intended for those who have little information regarding soapstone; undoubtedly men of practical experience will find many points for criticism.

Jan 1, 1929

An overland belt conveyor system installed at Simco-Peabody's mine near Coshocton, Ohio, is presently carrying coal three miles at an estimated cost of 4.499 per ton-mile. Installed by Link-Belt Co. in late 1961, this system transports coal from open pit and underground mining operations to the Conesville Power Plant. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. In 1960 the power plant completed plans to enlarge by adding a third boiler. As a result, Simco-Peabody was required to provide means to produce and handle more coal. The haulage equipment, which consisted of one 90-ton, five 60-ton and one 50-ton off- highway trucks, was too small to handle the increasing daily coal demands. Annual tonnage was approaching a million tons and in a few years would be well over that figure.

Jan 4, 1963

Howe Memorial Lecture The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and -practice of iron and steel metallurgy- or-metallography, chosen -by-the Board-of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated 1924 What is Steel'., By Albert Sauveur.

Jan 1, 1938

Featured at the 1977 SME-AIME Fall Meeting in St. Louis is a Lead-Zinc Update, organized to complement the 1970 AIME World Symposium on Mining and Metallurgy of Lead and Zinc, also held in St. Louis. The 21 papers comprising the Update are to be presented during four technical sessions at the Fall Meeting; in addition, the papers have been collected in a bound book available at meeting time.

Jan 9, 1977

THE CHAIRMAN.-Thank you. Since the papers are rather closely related, I think rather than taking them one at a time we will entertain discussion on any of these problems at this time. W. A. REICH.*-We, of course, quite a while ago got the yellow light that Mr. Cole spoke of, and like everyone else immediately started to study silicon bronzes and brasses. We were interested in the silicon bronzes and brasses because we felt that in order to replace gun metal which makes up a large part of our use we needed something with an elastic limit at least equal to that of gun metal. That means at least 12,000 lb. per sq. in. This study was aimed only at tin conservation. Then we dropped the study of silicon bronzes because high purity copper which is needed in their manufacture became a scarce item. To make a long story short we have recommended to our designing engineers that they use 85-5-5-5 wherever possible because 85-5-5-5 we understand can be made entirely from scrap with little or no tin addition. 85-5-5-5 has a lower elastic limit than 88-8-4, so we felt that we would need another substitute material, a structural alloy with an elastic limit equal to that of 88-8-4, and we immediately turned to the manganese bronze type of alloy. The poor foundry properties of standard manganese bronzes were mentioned by Mr. Thieme and since we feel that high zinc content is largely responsible for this difficulty, our development is directed along the lines of uncovering a material with a lower zinc content and which gains its elastic strength from the addition of other alloying elements, such as, aluminum, manganese and iron. It must be possible to make this alloy entirely from scrap with no additions of scarce high purity material. I would appreciate an expression of opinion on how low we can go in zinc content with this type of alloy without seriously impairing the availability, and how high we can go in aluminum content without making use of aluminum restricted for that use. We assume that the maximum lead content must be placed at 1 ½ per cent to insure good availability and we feel that about I per cent of tin in the alloy would improve salt water corrosion resistance similar to the effect of tin in Admiralty Metal. Has anyone here had experience with the effect of tin and lead on the weldability of such an alloy? C. S. COLE.-What percentage of lead and tin? W. A. REICH.-About 1 per cent of lead and 1 per cent of tin. We are studying the weldability of the alloy but perhaps someone already has the answer. (Pause, no answer) The claim has been made that 1 per cent of lead can be added to certain silicon bronzes without impairing their properties. A silicon bronze with a low zinc content requires high purity copper in its manufacture but if say the 15 per cent zinc, 44 silicon balance copper alloy could be made, with a I per cent lead content, some quantity could be made from scrap. We do not know whether the aforementioned is

Jan 1, 1943

AS we contemplate the bestowal of the John Fritz medal year after year on men of wide-world dis-tinction in the various fields of engineering, men who in one way or another have given impulse and direction to the progress of mankind, the question becomes inter-esting as to what manner of man was John Fritz and what were the qualities that singled out his name to be so conspicuously associated with the world's great scientific and industrial achievements. If, as Lowell said, it is the duty of the nation to pro-duce great men, our country surely rose to her oppor-tunity when she guided and guarded the career of John Fritz. Starting life as a blacksmith with no advantages of education, without influential friends or the favor-ing accidents of fortune, he advanced steadily in use-fulness, power and respect of his fellowmen until by common consent he occupied the first place in the domain of the steel industry of this, country. The numerous honorary scientific memberships conferred upon him in this country and abroad attest the esteem in which he is held by his fellow engineers. Twenty years after his retirement from active business at the age of seventy, he lived to enjoy, as few men have been permitted to do, the fame and the friendships which he had so amply earned. His sterner qualities of industry, integrity and sterling character were re-lieved by unfailing human sympathy, humor and spon-taneous good-will toward his fellowmen. To all who

Jan 3, 1928

By Horace C. Knerr

It has been shown that the resistance to corrosion of duralumin sheet is greatly influenced by the quenching medium used in heat treatment, or, more specifically, by the rate of cooling during quenching. The severity of corrosive attack after exposure to salt-water spray increases in .the following order: The tensile strength, yield point and elongation are only slightly affected by the quenching medium, as shown in Table 1. Tensile test requirements: yield stress, 25,000 lb. per sq. in. minimum; ultimate stress, 55,000 lb. per sq. in. minimum; elongation in 2 in., 18 per cent. minimum.

Jan 1, 1931

By Howard B. Gundersen

CURRENTLY the mining industry faces the twin tasks of producing metals in the largest possible amounts and doing it with a dwindling and less experienced labor supply. A manpower shortage during this emergency appears inescapable. It therefore becomes necessary to develop the highest possible efficiency. Employee training is a concomitant of economical, high production. Training keeps employee morale high, reduces waste, improves skills, and increases production without speed-up or overload of workmen or supervisors.

Jan 9, 1951

Works Manager or General Superintendent.-Technical graduate, for position with a company whose works consist of a large machine shop and foundry. This company manufactures well-known power plant equipment. Location, Pennsylvania. Salary, $5000-$8000 per year. R-871. Motion Study Engineer with extensive experience in shop operation and motion study. Must have sufficient technical experience to recognize inefficiency and waste in plant. Salary, $175-$200 per month. Location, New Jersey. R-876. Metallurgical Engineer.-Technical graduate with at least 2 or 3 years' practical experience in the operation of zinc smelters. Duties will be to take charge, under the guidance of -the superintendent of the smelter, of the operating end of the furnaces, and the roasting kilns, as well as the mix room and ore crusher. Man desired should not be over 30 years of age and should be progressive and able to handle men. Salary, $250 per month. Location, Oklahoma. R-877. Private Secretary to Vice-president in charge of development department and laboratories of large manufacturing plant; must be technical man of good personality, and A-1 in every respect, as position is an important and responsible one. Location, Ohio. R-896. Sales. Engineer familiar with his local territory, particularly with the fanning trade. Should have had at least 2 years' experience in selling tractors; and in any event, must have had at least 5 years' experience in selling machinery. High grade, energetic, and capable; man who is not satisfied with less than $3000 per year and who can earn up to $7000. Location, Iowa. R-897.

Jan 8, 1919

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

On Feb. 16, 1948, the Board of Directors of AIME authorized the publishing of "Technical Notes" in METALS TECHNOLOGY. The purpose is to provide prompt publication of wry short items of the following general types: 1. Results of short investigations which do not warrant a paper. 2. The conclusions of extensive investigations of insufficient general interest to justify a regular paper. 3. Conclusions arising in the course of an investigation, which, because of interest to others in the field, the author wishes to present prior to completion of the investigation. 4. Pertinent factual comment (not mere argument) on the subject matter of previous "Notes." Such Notes will be subject to the approval of the Auxiliary and AIME Publications Committees, but can be handled more promptly than regular papers because they need not be referred to readers. The recommended maxi- mum length is 500 words; notes in excess of 1,000 words will not be considered for this type of publication. A graph or photograph may be included as part of the note when particularly illustrative. As with regular papers, contributions to the new section should be submitted to the Secretary of the AIME.

Jan 1, 1948

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939