Search Documents

By Rafael Errazuriz

About eighty miles north of the city of Antofagasta, Chile, located just below the Tropic of Capricorn, there spreads a wide desert area where copper oxide outcrops can be seen with the naked eye. Numerous old mining works and dump heaps with the green of atacamite and chrisocolla shining in the blazing sun, attest to the work done by miners in the beginning of this century. The dry desert air preserves the footstep marks, paths and trails of old cartwheels from years back. The mining area known as Michilla and Panizos Blancos, is located on the high plateau at 3000 ft above sea level. Around 1920 a Bleichert ropeway was built, which carried ores from the best known mine to a wharf at the Michilla bay. High grade silicious ores were shipped to the Gatico Smelter further north or to smelters in the United States or Japan.

Jan 8, 1973

By Thomas V. Falkie, Robert Stefanko

Higher education is in serious trouble in the United States. With increasing costs threatening to create a taxpayer's revolt, serious thought must be given to determining whether or not we can continue to afford our present educational policies. Disinterested students with little aptitude are pushed into over- crowded universities by well-meaning parents, but they lack real objectives beyond achieving that great status symbol-the degree. Advanced degrees are heaped upon the baccalaureate degree, and the pursuit of the pure and social sciences continues at the expense of engineering and technology.

Jan 1, 1971

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By George W. Lower, Robert B. Booth

The use of cyanides in the extraction of gold and silver is well known1 Such extractions employ concentrations of cyanide in the range of 0.02-0.25% sodium cyanide equivalent in leaching cycles of 24-48 hr and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold.2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure.

Jan 11, 1965

Bellows Connector Fabricated of chemically inert Teflon, the new bellows type connector has many pipe line applications where vibration, expansion and electrolysis exist in the handling of corrosive liquids or gases and solvents. The new connector is electrically non-conductive, flexible even at 94°F and as strong as 480°F as at 70°F, according to the manufacturer. This bellows connector serves as a [ ] vibration dampener as well as an expansion joint and connects misaligned couplings and insulates flanges electrically. End flanges of the joint are French-type envelope gaskets made integral with the joint for easy assembly between companion flanges and a tight, leak-proof seal on installation. Circle No. 1

Jan 1, 1952

In introducing last year's Industrial Minerals Review, Stan Lefond accurately predicted that the 1974- 75 period would be quite difficult and frustrating. Although 1974 demand and prices for most industrial minerals were exceptionally strong, operating costs also rose rapidly-while shortages of supplies and equipment, symptomatic of an overheated economy, occurred from coast to coast. Thus, at the end of 1974 recessionary forces were accelerating-and the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken, the high-volume, low-prices industrial minerals will incur sharply increased unit costs. To maintain adequate profit margins under these conditions will require cautious and perceptive management.

Jan 2, 1975

By C. W. Carpenter, P. T. Bail, J. E. Bobek

This paper presents the results of model studies made to demonstrate the validity of applying the "basic" waterflooding scaling relationships of Rapoport1 to water-wet reservoirs composed of communicating strata of different permeability. Results demonstrate that these relationships can be validly applied, and also show the combined effect of variables on recovery. This demonstration was needed to confirm that the sizable effects of communicating strata on waterflood behavior, observed in model studies, were actually representative of field behavior. INTRODUCTION Rapoport1 Collins2 and others have presented scaling laws for modeling water-oil displacements. The validity of these laws has been experimentally demonstrated for homogeneous systems only. Recently, however, several investigators have presented the results of multilayer model studies made to determine the effects of viscous, capillary and gravitational forces on oil recovery in systems composed of communicating layers of different permeability. Dyes and Braun,3 using miscible displacements to simulate water flooding, showed that vertical communication adversely affects recovery at unfavorable viscosity ratios in the absence of capillarity. Ogandzhanyants and Egorova, 4 Gaucher and Lindley,5 and Richardson and Perkins6 modeled water-oil displacements in layered systems using immiscible fluids with capillary forces present. These investigators found more efficient behavior than in the miscible system of Dyes and Braun. However, since the scaling laws had not been verified for heterogeneous systems prior to or during these tests, it was necessary to assume that the results were representative of field behavior. This report presents the results of model studies made at Jersey Production Research Co. to find out if the waterflooding scaling relationships are valid when applied to water-oil displacements in heterogeneous reservoirs with vertical communication. Data obtained in the study show the combined effects of viscous, capillary and gravitational forces on oil-recovery behavior. The studies were performed in strongly water-wet systems where strong imbibition forces were present. For systems of different wettability, the effects of capillary imbibition would be somewhat different than those presented. APPROACH The scaling laws studied were those developed by Rapoport1 and designated by him as "basic" scaling laws. These relationships require that the model be scaled to the geometry of the prototype, and that the model and prototype be operated at the same viscosity ratio and have identical relative permeability curves, contact angles and boundary conditions. It is also necessary that the groups** be identical in the two systems, although any of the parameters making up the groups may be different. Finally, the capillary pressure of one system must be directly proportional to that of the second. Studies were conducted in two four-layer models, representing quadrants of five-spots, which were geometrically similar and which had the same glass-bead packing. The fluids used assured the same wettability in both models. Thus, the contact angles and relative permeabilities of comparative sand layers in the two models were identical and the capillary pressures were directly proportional. However, one model had a characteristic length three times that of the other. To make the scaling groups equal and to check the scaling laws, it was necessary to adjust the rate, water-viscosity level, interfacial tension and water-oil density difference to compensate for the difference in model sizes.

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

* A loan, perhaps as great as $100 million, from American insurance companies is about negotiated for development of Labrador iron ore properties. The program will call for a total expenditure of up to $200 million, including, as well as all mine development work, the power facilities, housing for mining personnel, and auxiliary equipment. * Mobile air compressors and a water tank, mounted on a 30-ton rubber-tired trailer and towed right up to the drilling crews, eliminates the need for expensive underground water and air pipe lines in the experimental oil shale mine operated by the Bureau of Mines near Rifle, Colo.

Jan 11, 1950

The thirty-ninth meeting of the Boston Section was held at the Engi- neers? Club on Monday evening, Dec. 4, 1916. Thirty-three members and guests sat down to dinner; There were present as section guests; Dr. L. D. Ricketts, and Prof. Bradley Stoughton, President and Secretary of the parent society, and each was called upon to speak. Mr. Stoughton spoke of the growth of the Institute during the past year and described the very numerous and important activities, of which the junction of the American Society of Civil Engineers with the other three societies is perhaps the most important. Dr. Ricketts, the advertised speaker of the evening, spoke on Recent Progress in Mining and Metallurgy of Copper Ores. In discussing the improvements in mining, he traced the mining methods from square- set mining to the modified Ohio System now so successfully used at Inspiration: In metallurgy, he described the growth of reverberatory-smelting ant1 allied problems such as the utilization of the waste heat for generating steam. He laid stress on the importance of sampling and bedding of

Jan 6, 1917

By John W. Stevenson

In gassy coal mines, abandoned worked-out areas are natural reservoirs that may contain air- methane mixtures. The quantity of such mixtures is continuously increasing or decreasing as atmospheric pressure falls or rises. This is in accordance with Boyle's Gas Law, which states that the volume of a perfect gas varies inversely with the absolute pressure. In large, open gob areas without a bleeder ventilation system, atmospheric pressure is a static force acting in all directions. Changes in atmospheric pressure may occur rapidly or slowly, but any change will result in a change in the quantity of gob air-methane mixtures.

Jan 6, 1968

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

IN NOVEMBER 1933 I had the pleasure of receiving an autographed copy of a small brochure entitled "Birth of the Porphyry Coppers." The author, James Colquhoun, a distinguished British mining engineer, had been the dominant figure in the Arizona Copper Company, Limited, which, until its acquisition by the Phelps Dodge Corporation in 1921, had been the principal producer of copper in the Morenci district. In addition to the highly productive Humboldt and Longfellow mines it owned the Clay property, which, of course, has now become Arizona's No. 1 copper mine. Except for Utah Copper it is the premier Porphyry copper enterprise in the United States. Mr. Colquhoun's little volume was inspired by THE PORPHYRY COPPERS which had appeared early that year. In a most courteous and friendly way he adduces data to show that "we (Arizona Copper Company Limited) were successfully treating low-grade porphyry ores in quantity for at least four years (1901 to 19W) before the Utah Copper Company did anything at all." This last remark is based on the figures in THE PORPHYRY COPPERS showing that Utah's first production came from the Copperton pilot plant in 1905. Mr. Colquhoun traces the story of Morenci beginning in 1883 when he first arrived there. He tells how the rich self-fluxing ores (containing lime- stone, silica, and iron in proportion to permit direct smelting to produce black copper) were gradually exhausted. High-grade siliceous ore could be mixed in limited quantity with the self-fluxing ores; and oxidized ores were leached to contribute substantially to the production of the district. But

Jan 1, 1957

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By A. Wahab Khair

This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally con- fined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage.

Jan 1, 1984

By Oliver U. Bradley

The conditions affecting the supply of casinghead gas, the different degrees of productivity, the difficulty of determining the quantities utilized, and the evaluation of the gas in casinghead-gasoline units and related data, having an economic bearing on the industry as a whole, are important questions and offer an interesting field for study. Casinghead-gas data have been gathered in some of the oil fields of Oklahoma where testing work has been done regularly and the volumes of casinghead gas were available. The area covered embraces 219 scattered leases in 29 townships, with a total of 18,039 acres and 1921 wells. The accompanying table gives specific locations of the areas under consideration, number of leases, range depth of wells, average age of production, sand depths and oil production data. The results of this investigation are set forth in the accompanying charts, showing volumes of casinghead gas in 6-month periods from Jan. 1, 1918, to June 30, 1921, when full record was available, production of casinghead gasoline, average productivity of the gas in gallons per thousand cubic feet, average price of the gas and the market price of the casinghead gasoline. The cases enumerated in the table and the data shown in the graphs do not represent the greater part of oil or casinghead gas production from any one township, nor are the leases contiguous. The properties in each township, however, may be considered as typical of general conditions, such as the date of completion of wells, depth, character, and thickness of oil sand, time of pumping, present oil production, Vacuum carried on wells, and usual operating practices. It was deemed advisable to subdivide the time into 6-mo. periods, as it was impracticable to make the tests more frequently, furthermore 6 mo. is probably the minimum period within which there would occur a noticeable increase in the productivity of the gas. It must be remembered that the figures on volumes are subject to the usual irregularities and relative inaccuracies of meter measurenlents of gas under varying degrees

Jan 1, 1924

The opening session was held on Tuesday evening, June 28th. Mr. F. S. Witherbee, of Port Henry, a member of the Local Committee, welcomed the Institute as follows: Mr. President and Gentlemen and (if I my also add) Ladies of the Institute: In the absence of the Chairman of our Local Committee it is my pleasant duty to give you a cordial welcome once more to the shores of Lake Champlain. I think some fourteen years have passed by since we last had the pleasure of receiving you at a meeting in this vicinity ; but the pleasure of that meeting still lingers in our memory; and the profit which we derived from your discussions and from your presence with us has made us heartily desirous to have you here again. If the truth must be known, we were for a time much embarrassed by the difficulty of providing adeqriate and comfortable shelter for the large number of friends whom we hoped (and, as this assembly indicates, had good reason for hoping) to receive. But the liberality and zealous co-operation of the Delaware & Hudson Canal Company and its hotel manager, in offering to open Hotel Champlain, at no little inconvenience, before the usual time, presented a solution of this difficulty, provided the date originally proposed for the meeting could be changed to a week later. This change was duly authorized; .and I think you will all agree with us that it was wise.. At all events, I am sure, I now need offer no apologies for the roof which covers yau. During the fourteen years which have elapsed since your last visit to us, great strides have been made in the industrial development of this country. The meetings of the Institute, held from one end of the land to the other, have permitted you to witness the transformation of small hamlets? like Birmingham, Ala., into populous and thriving industrial centers. You have seen the Minnesota and the

Jan 1, 1893

The Committee appointed by your Board of Directors to nominate Officers for the Institute for the year 1915 invites the participation of all members in the nominations. The suggestion of names for the various offices will be appreciated and given full consideration when making the selection of candidates which this Committee will recommend. The officers to be elected at the annual meeting in February, 1915, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows:

Jan 6, 1914

By ir. H. Eraly

At the Zolder mine a S/7 computer is used for two purposes : - to monitor production at the coal face - to monitor the distribution of mine cars. By using sensors attached to equipment at the coal face and at the loading points, the computer provides realtime information and also summarized reports, which help management to control production better. The computer will display this information to the control room, where two operators monitor all production events and the availability of the right numbers of mine cars at every production face. All benefits obtained from the system are described.

Jan 1, 1977

By John A. Bonucci

AMAX Base Metals R&D, Inc. has developed technology for extracting and recovering platinum and palladium from spent automobile exhaust emission control catalyst. Our most promising route is a chloride-based hydrometallurgical flowsheet in which catalyst pellets or crushed monoliths are leached in HC1 with an oxidant at 95°C without agitation. Alumina co-dissolution can be limited by thermal pre-treatment of the catalyst. The leach solutions are treated by one of several precious metals recovery techniques to produce a high grade PGM concentrate. For the new generation of three-way catalytic converters which contain rhodium, an H2S04 preleach could selectively extract much of the rhodium while leaving the platinum and palladium behind. Capital and operating costs will be discussed.

Jan 1, 1984