Search Documents

By S. S. Cole, D. L. Armant

The smelting of titaniferous ores for the past hundred years has not been successful because of thickening of the slags in the furnaces. The interest in the utilization of these iron bearing materials has been due to the extensive deposits which have been found in various parts of the world.1 The literature contains references2 to the use of titaniferous ores in blast furnaces. None of these attempts has met with success due to the lack of sufficient information as to the cause of failures and to economic considerations. Evaluation of the published information, as to the probable cause of failure in various attempts, has indicated that the presence of lower valence titanium oxide and formation of titanium carbide contributed to the failure. It was apparent that severe reducing conditions which are present in a blast furnace had been one of the factors for such failures. The previous smelting operations had as a primary objective the recovery of iron from these ores. Under these conditions the highest recovery of iron could only occur with severe reducing conditions. Application of Melting Point Data The application of the melting point data, from the system CaO-MgO-Al2O3-TiO2 reported in another paper,3 to the smelting of titaniferous ores required an extrapolation of these melting points due to the presence of other impurities from the ores. Likewise, a study of the effect of varying FeO and reduced titanium content of the slag was necessary before the data could be fully applied. The melting point data under oxidizing conditions had clearly indicated that a fluid slag with a melting point in the temperature range of 1370°C could be obtained. The smelting of a titaniferous ore had as a primary objective the production of a high titanium slag which was fluid and substantially free of iron and low in trivalent titanium. Since production of a high titanium slag was of primary importance, rather than the recovery of iron from these ores, the smelting concept could be altered to a marked degree. The ferrous oxide could be maintained at higher levels than is the normal practice in iron ores slags without being detrimental to the slags, although a loss in iron recovery resulted. During the reduction of the molten mixtures of ferrous iron and titanium, carbon acts as the reductant for changing the valence of the titanium and iron. The reaction can go further than in the case of the reduction which occurs in iron-titanium solutions. The formation of metallic iron removes iron from the system, so that the titanium oxide can be reduced to trivalent and divalent titanium oxides and also form titanium carbide which removes the titanium from the slags as a soluble constituent. The problem, therefore, resolves itself into maintaining the proper amount of ferrous iron in the slag thereby avoiding the formation of appreciable amounts of trivalent titanium and no divalent titanium oxide or titanium carbide. The latter two have been found in the viscous

Jan 1, 1950

By T. P. Clendenin

THE northerly two thirds of Mexico falls into five main physiographic divisions, illustrated on the accompanying map. In form, these divisions are a series of strips, paralleling the northwest-southeast axis of the country.

Jan 10, 1951

John Malcolm Fraser became Prime Minister in December 1975 when Australian voters gave him the biggest landslide victory in the history of the Federation. From the previous administration, Mr. Fraser has inherited an atrocious economic mess: a staggering budget deficit, an unrealistically overvalued currency, a 14% annual rate of inflation, mounting unemployment, and a demoralized business community. He has already tackled some of these problems with some measure of success; but he has been in power for barely a year, and it's too soon to see a turn-around.

Jan 1, 1977

A. Scott Reid, London, Eng. (communication to the Secretary*) :—As a constructor of several glass mine-models, .I have read with much interest the description of the model of the Montana-Toriopah mine-workings by Edmund D. North.

Jan 1, 1910

By G. K. Zaharlev

With a productive output growing at an annual rate of 8%, the Soviet mining industry should emerge as the world's leader in total mineral output during the 1980's. (The Soviet Union's share in the world's total mineral output in 1973 was estimated at 22 to 23%.) According to estimates by Soviet mining experts, the mineral potential of the Soviet Union will sustain the current 8% annual growth rate in the future.

Jan 12, 1974

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By AIME AIME

WHEN the War Production Board issued its order which will end the use of iron and steel in more than 400 familiar civilian articles, the list of those products formed a fascinating and homeric catalogue of the things we use. Articles for which iron and steel may not be used after a 90-day "tapering-off" period are as workaday as office machinery and as frivolous as cocktail shakers. Mostly they are smaller items-the smallest probably are phonograph needles but in the aggregate they will save tremendous quantities of the metal most needed to win the war. In total war there are no trifles. Interesting proof of this lies in the fact that by eliminating manufacture of blackhead squeezers we shall save 110,000 lb. of steel a year. Out of this steel we might have made four 155-mm. field pieces. We might have made a thousand 3-in. trench mortars, 4400 0.30-caliber machine guns, 55 16-in. shells, 110 200-lb. aerial bombs, or three 15-ton tanks with something left over to arm them.

Jan 1, 1942

By Carl Scholz

FROM the engineer's standpoint, labor organizations are of interest in so far as they 'affect efficiency, maximum production and unit cost, and in this respect the earlier labor organizations' which existed in the age of the Guilds were ideal, inasmuch as they stood ' for competency of the apprentice and close cooperation ' between employers and employees. In later years the tendencies of the labor organizations have gone in the opposite direction and, instead of cooperating 'with the engineer, they usually oppose him on the mistaken theory, that labor-saving devices reduce forces, and costs; in this respect, the united Mine Workers of America have been particularly active and, to a very great extent, successful.

Jan 1, 1921

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976

By James Howard

ON Aug. 25, 1911, a rail failed on the Lehigh Valley Railroad, causing a disastrous wreck. The surface of the fracture was in a plane at right angles to the length of the rail. There was a dark-colored, oval spot on this surface, located on the gage side of the head, representing the part of the rail which was the first to fracture. The nucleus of this spot showed that the fracture had an interior origin. Other fractures of this kind, the peripheries of which had not reached the surface of-the rail, presented surfaces having a silvery luster. The darkened surface of the present fracture was caused, doubtless, by the air having had access to it. This fracture was recognized as a fatigue fracture, of a modified type, its interior origin having been due to a component in the rail which is not usually present in cases of fatigue fractures. The metal next the running surface of the head of the rail was in a state of internal compression, this being the component not commonly met with in other cases, and which caused the fracture to have its interior origin. For the purpose of giving this modified type of fatigue fracture a specific name, for identification, the term "transverse fissure" was applied. No mystery was thought to attach to its formation, or to its development. The explanation of its occurrence was obvious in the light of common knowledge upon the behavior of steel under repeated alternate stresses. By reason of the state of internal compression at the running surface, the maximum tensile stresses in the head, under bending loads, were along an interior element. Here the tensile strains were higher than in the fibers more remote from .the neutral axis. Under such conditions the fracture of the rail would be expected to have an' interior origin. A discussion of the subject of transverse fissures essentially becomes a discussion of fatigue fractures, since they are identical. The descriptive term employed, merely for the identification of this type of fatigue fracture, had the appearance of creating alarm. Apprehensions arose that a new phenomenon in the physical properties of steel had presented itself, the explanation of which was sought in every

Jan 11, 1917

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe's laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor's occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe's laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor's occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By R. F. Decker, J. R. Mihalisin

Phase transformations in a series of relatively pure nickel-titanium-aluminum binary and ternary alloys were studied. The purpose was to clarify age-hardening mechanisms, especially in predominantly titanium-hardened compositions. The micro-structures, as determined on a tirne-temperature-transformation basis by light and electron microscopy and X-ray diffraction, were correlated with room temperature and hot hardnesses. The stability of the ? phase under nonequilibrium conditions was shown to be important in this system. MANY of the alloys designed for service in the temperature range of 1200oF (649°C) to 1800°F (980°C) are austenitic iron-.nickel base alloys hardened by titanium and aluminum. The control of high-temperature properties of these alloys has been advanced by the knowledge of microstructures provided by the equilibrium diagrams of Taylor and Floyd1 and Taylor.2, 3 However, there have been notable instances in the predominantly titanium-hardened alloys where the correlation of properties with microstructure and the equilibrium diagrams has been unsuccessful. Mihalisin and carrol14 have noted in electron microscope studies of commercial alloys of this type that a fee phase precipitates and transforms to 71 (hep Ni3Ti) in stress-rupture tests. Bieber5 found that this fee phase remained in nickel-chromium-titanium alloys even when aluminum was excluded. Age hardening in iron-nickel base alloys has been attributed to 71 by Craver, Aggen, and Dyrkacz,6 ? (fee phase based on Ni3Al) by Beattie and Hagel7 and both phases by Lena,8 Yet, on the basis of the nickel-titanium-aluminum equilibrium diagram of Taylor and Floyd shown in Fig. 1, it has been difficult to understand the presence of ? in low aluminum alloys. Furthermore, the characteristic coarse dispersion of 71 has not been commensurate with the marked aging response. Also there have been anomalous grain boundary transformations in the iron-nickel base alloys which have markedly reduced notched stress rupture properties.9 These have been related to boron content and residual cold work. Recently, Golubtsova and Mashkovich,10 Buckle and Manene11 and Bogaryatskii and Tyapkin12 have noted a transition fee Ni3Ti in titanium-hardened nickel-base alloys. It was apparent from the latter studies that a transition phase was important in the nickel-titanium-aluminum system. The purpose of this study was to identify this phase, measure its transformation characteristics and kinetics, and attempt to correlate these findings with age hardening. It was believed that time-temperature-transformation studies, because of their adaptability to transition phases, would be of most value for this investigation. Accordingly, this method of study was undertaken on relatively pure nickel-titanium-aluminum alloys with controlled variations in boron content and residual cold work. EXPERIMENTAL PROCEDURES Compositions were selected from the nickel-titanium-aluminum isothermal section of Taylor and Floyd.' These compositions are plotted in Fig. 1 and were selected to obtain equal aging potential of approximately 15 pet by volume of the equilibrium precipitate. The materials were vacuum melted from

Jan 1, 1961

By T. M. Broderick

InveStIgations into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attracting increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minnesota (which spends about $80,000 annually on problems of the iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.' Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was outlined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert. About 85 per cent of the iron and steel produced in the United States comes from ores of the Lake Superior district. The reserves of direct

Jan 1, 1935

By T. M. Broderick

InveStIgations into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attracting increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minnesota (which spends about $80,000 annually on problems of the iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.' Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was outlined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert. About 85 per cent of the iron and steel produced in the United States comes from ores of the Lake Superior district. The reserves of direct

Jan 1, 1935

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By T. M. Broderick

INVESTIGATIONS into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attract-ing increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minne-sota (which spends about $80,000 annually on problems of the 'iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.1 Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was out-lined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert.

Jan 1, 1933

By M. O. Holowaty, C. M. Squarcy

Bituminous coal furnaces give way to coke, and by 1880, the American iron and steel industry was growing at a tremendous rate. In the twentieth century, the number of operating blast furnaces was cut in half while pig iron capacity more than doubled. Bituminous coal furnaces Attempts to relieve the shortage of charcoal by the use of bituminous coal in American furnaces began quite early. Use of bituminous coal in the blast furnace was restricted to areas lacking anthracite deposits but rich in deposits of bituminous coaL The largest concentration of bituminous coal furnaces was in Western Pennsylvania, West Virginia and Western New York state. Other areas included Kentucky and southern portions of the states of Indiana and Illinois. The first trials were made in Pennsylvania around 1780. Gradually several more furnaces began charging coal with their burdens as a partial substitution for charcoal. These so called cheaters were numerous, especially in Western Pennsylvania, which around 1810 began to expand its ironmaking capacity to catch up with the Lehigh Valley and the Schuylkill According to the existing references, complete bituminous coal burdens began to be used in this area only around 1840 when the ironmakers hastily adopted the hot blast apparatus introduced from England. The majority of these furnaces were built, however, after 1844 when an extensive experimental program, carried out at the Shenango Steam and Water Hot Blast Charcoal, Coke and Raw-Coal Furnace produced favorable results, with coal containing up to 35 pct volatile matter. The furnace was located near the Shenango River on the Lackawannok Run, five miles northwest of Mercer, Pennsylvania. It was built, owned, and operated by David Hogeland of Mercer. The first furnace was built in 1836 or 1837 as a charcoal furnace. Soon, however,

Jan 1, 1961

By M. Cohen, D. Caplan

The scaling characteristics of three Fe-Cr alloys have been investigated by determining their weight gain vs. time curves at 1600° to 2000° F. The scales formed thereby have been examined using the techniques of X-ray diffraction and spectrographic and metal-lographic analyses in an attempt to explain the discontinuities in the curves and to elucidate the mechanism of scaling. DESPITE the considerable number of investigations that have been carried out on heat resistant alloys, the characteristics of the scales formed at high temperatures are not fully known. The research reported here was undertaken in an attempt to ascertain the mechanism of scaling of the stainless steels. Scaling experiments were carried out first, the weight increase of the specimens being followed continuously with time. It was observed that, as well as showing the expected decrease in oxidation rate with time, the oxidation curves showed breaks corresponding to intermediate periods of accelerated oxidation, after which protectiveness again increased. This phenomenon was observed with austenitic stainless steels (types 302, 309, and 330) and with Fe-Cr alloys (types 410, 430, and 446), but only the latter are treated in this report. An examination of the scales was made using the techniques of X-ray diffraction and spectrographic and metallographic analyses in an attempt to obtain a correlation between the nature of the scales and the oxidation curves. A search through the literature revealed only a very few previous reports of such periods of accelerated oxidation. Dunn' found breaks in the oxidation-time curves of some Cu-Si alloys but saw no rational explanation of the phenomenon. Heindlhofer and Larsen2 attributed a discontinuity in the weight gain-time curve of iron at 1290°F to the formation of blisters, the subsequent cracking of which exposed an unprotected surface and permitted rapid oxidation until a new protective scale had been reestablished. They advanced no explanation, however, for what they termed the peculiar behavior of a 27 pct Fe-Cr alloy at 2000°F which gained weight very rapidly in between two periods of very slow weight gain. Portevin, Pretet, and Jolivet3 in describing breaks in the weight gain-time curves of Fe-A1 alloys suggested that they might be associated with the occurrence of localized and deeply oxidized areas on the specimens. Bandel4 in a general discussion of oxidation curves of heat resistant alloys considered that the discontinuities were due to a local disruption of the protective layer by the growth of iron-rich oxides. Day and Smith" in their report on the scaling of a large number of iron alloys noted but did not explain occasional relatively rapid changes in oxidation rate at higher temperatures. Chevenard and Wache6 found breaks, often two per specimen, in the oxidation curves of an 18-8 type alloy. They suggested that the cause might be a depletion in chromium of the surface layer of metal due to its selective oxidation, the resultant high concentration of iron and nickel in the scale leading to a poorly protective scale. McCullough, Fontana, and Beck' explained the breaks in the oxidation curves of types 304, 430, and 410 alloys as due to mechanical ruptures. Experimental Work Table I lists the chemical compositions of the materials used. Cylindrical specimens 1/4 in. in diam and 11/2 in. long were machined from cold rolled % in. rod. After a fine finish cut with a sharp tool, the specimens were abraded while still mounted on the lathe with Nos. 2, 1, 0, and 00 metallographic grade emery papers. A 3/64 in. hole was drilled at a distance of 1/8 in. from one end to permit suspension in the furnace. Specimen Nos. 1, 2, and 3 were tested with this surface preparation. All others, after being similarly prepared, were electropolished in a perchloric-acetic electrolyte, electrical contact being made by pressing a tapered platinum hook into the drilled hole. The specimens were then washed in hot water, rinsed with distilled water, rinsed with methanol, dried at 120°F, and weighed. Thereafter,

Jan 1, 1953