Search Documents

By W.G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By W. G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By C. E. Dobbin

THE identification of rock formations by a study of certain physical characteristics of burned samples was introduced in Wyoming in 1,926, when W. G. Buckles, superintendent. of the brick department of the Parco Development Co., reported to officials of the Producers & Refiners Corpn. that shales from the Cretaceous and older formations exposed between Parco and Rawlins exhibited distinctive coloration and textural features when burned in a standard brick kiln at temperatures ranging between 1000° and 3000° F. In collaboration with Elfred Beck, chief geologist of the Producers & Refiners Corpn., Buckles later burned cuttings and cores from several Wyoming wildcat wells in a standard kiln and successfully identified certain subsurface formations which had not been satisfactorily identified by other means. The results of their investigations were outlined in papers presented by Beck before the American Association of Petroleum Geologists at San Francisco in March, 1928, and by Buckles at. a joint meeting of the Rocky Mountain Oil and Gas Association and the Production Division of the American Petroleum Institute at Casper in November, 1928. These papers have not been published. The investigations set forth in this paper were carried out for. the purpose of determining the value of certain ceramic tests in assisting the petroleum engineers of the U. S. Geological Survey to identify well cuttings that represent Cretaceous shales penetrated beneath unconformable Tertiary formations in central, and eastern Wyoming, but that yield neither lithologic nor paleontologic criteria for satisfactory correlations with distinctive weathered outcrops. The investigations were made in the chemical laboratories of the Geological Survey at- Midwest, Wyo., and consisted of studying certain physical characteristics of burned bricks from representative outcrop samples of unweathered Cretaceous shales and of similarly burned cuttings of the same shales collected from wells in the Salt Creek oil field.

Jan 1, 1931

By John D. Wiebmer

There are those in the Colstrip, Mont., area who can still remember the opening of the Rosebud mine in 1923. For 35 years it was a steady employer of 80 or 90 residents who produced coal for the railroad. In 1958, though, mining ceased as diesel locomotives supplanted steam engines. The mine was purchased in 1959 by Montana Power, the parent of Western Energy Co., and production resumed in 1968. Long Construction Co. was chosen as operator of the mine equipment. At that time, reserves appeared virtually unlimited. The thick Rosebud seam coursed through alternate sections of railroad holdings and federal land-then came the federal moratorium on coal leasing in 1971. About the time Western Energy completed the special leasing procedure to extend reserves from an existing mine, a new federal monkey wrench was thrown into the works with passage of the Surface Mining Control and Reclamation Act of 1977.

Jan 12, 1979

By G. R. Green, R. C. McDonald

The International Nickel Co., Ontario Div. mines, faced with rising production requirements, short labor supply, and ever increasing labor costs turned to mechanized mining for a solution to its problems. The degree of mechanization of ore removal has increased from 1966 with the purchase of the first diesel-powered load-haul-dump (LHD) machine to the present, with over 53% of all underground production handled by these units. Keeping pace with mechanized ore removal, there has been a parallel development of drilling equipment to complement the mucking units. This paper deals with the applications and economic advantages of mechanized drilling at the underground mines of Inco, Ontario Div. It covers the use of various types of mechanized drills in such mining methods as cut-and-fill, induced block caving, and sublevel caving. The economics of raise boring are also discussed.

Jan 1, 1974

Curlisle: We're sitting in Don McLaughlin's office overlooking Sun Francisco Bay, and he's going to be good enough to talk about early days in California, maybe about his college years in Berkeley, maybe about his first jobs in mining. Now, Don, would you be good enough to start it off by saying something about George Hearst. I know he died before you were born, but you know a lot about the family, and you no doubt know a lot about him. Certainly, nobody in those days matched his record in getting hold of good mines. McLaughlin: George Hearst died, actually, in the very year that I was born, but as I more or less grew up in the home of Mrs. Phoebe Hearst, who was his widow, I heard a great deal about the mines and the people that made the great fortune she inherited and used so wisely. But I don't think I really had an appreciation of George Hearst until 1 became active in the mining world and realized how many major mines he had picked in the early days and how much he had to do with their development into successful properties. He started in the California gold fields, but it was on the Comstock that he made his first big stake out of his substantial share in the Ophir mine. I believe at that time he was on his own. Then, later, he became associated with Ben Ali Haggin and Lloyd Tevis in San Francisco, and scoured the West for them. They made a little money in Eureka, Nevada, and other places, but the first important property that he obtained for them was the famous Ontario Mine in Park City, which became one of the great silver lead producers of the Continent. Then later he acquired the Homestake.

Jan 6, 1965

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By L. E. Young

THE progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. INTRODUCTORY STATEMENT AND SIGNIFICANT POINTS IN PROGRESS Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: I. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods and the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, considering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for the mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics, petroleum engineering, petroleum technology, ceramics and so forth. 7. There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1947

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company's initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company's holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By H. W. Schadler

Single crystals of tungsten, which were grown by electron bombardment floating zone refining, were strained 2 pet in tension and bending at 298°, 77°, and 20°K to determine the modes and crystallography of the plastic deformation of these temperatures. At 77° and 20°K plastic deformation occurs by slip on systems of the type (011) [111] and by twinning on (112)-type planes. For crystals strained at 298°K, deformation occurs by slip in [111] directions on either (Oil)- or (112)-type planes. CURRENT models for the initiation of brittle fracture in crystalline materials are based on a knowledge of the details of their plastic deformation.1 Body-centered cubic tungsten exhibits brittle failure at temperatures below about 500 °K yet the modes and crystallography of its plastic deformation have not been studied below 1000°K. In 1924, Goucher2 reported that tungsten single crystals with a total impurity content of less than 0.01 wt pet deformed by slip on the (112) [111] system in the temperature range 1000° to 3000°K. He also observed (001) [010] slip in one crystal which was constrained by the presence of a large fissure. According to Barrett3 tungsten also deforms by twinning on the (112) plane in the [111] direction, but he gives no details on the tendency for twin formation or the temperature range in which twinning occurs. Therefore, as a necessary part of a study of the factors influencing the brittle fracture of tungsten, the modes and crystallography of the plastic deformation were determined at 298°, 77°, and 20°K. Tungsten single crystals, grown using the electron-bombardment zone-refining technique first described by Calverly,4 were deformed to between 1 and 2 pet plastic strain in tension and bending. The surface offset resulting from slip or twinning was observed with an optical microscope to determine the crystallography of the deformation. The existence of twins was proven by the standard polishing and etching technique; and the crystallography of dislocation motion was followed using the dislocation etchant described by Wolff.5 Some observations on the fracture characteristics of tungsten single crystals are included. EXPERIMENTAL TECHNIQUES Growth, Purity, and Perfection of the Crystals-Several years ago Calverly, Davis, and Lever4 dem-onstrated the feasibility of growing tungsten single crystals by the electron-bombardment floating zone-refining technique, and Carlson6 showed that crystals produced in this way had a high degree of purity and were ductile at room temperature. Tungsten single crystals produced by this technique in equipment similar to that described by Carlson were used in this study. The starting material, a powder metallurgy product, was obtained in the form of a swaged 1/8-in. rod from the General Electric Wire Plant in Cleveland, Ohio. The crystals were grown from this material in a vacuum of 10"4 mm of Hg by passing a molten zone 1/8 in. long down the rod twice at a speed of 3 mm per min. At this zone speed

Jan 1, 1961

By G. H. Shefelbine

DISCOVERED during the time of the Spaniards, the Namiquipa silver-lead-zinc mines in Chihuahua, Mexico, remained idle until 1916, when mining claims were first denounced. About 1922 a Japanese company, the Santo Domingo Mining Co., was formed to mine the oxide silver ore. The company built a 75-tpd cyanide plant and mined in the area for a number of years. Because of an error in surveying in one of the company's mines situated in another district, mining was carried over into a claim owned by General Marcel Caraveo, at that time governor of Chihuahua. Santo Domingo Mining Co. lost the resulting lawsuit and consequently had no capital to continue operating at Namiquipa. Later, Ray Brown and Eugenio Caballero formed a company to operate the mine, shipping crude ore to the American Smelting and Refining Co. smelter at Avalos, Chihuahua. The cyanide plant was changed to flotation with a capacity of 75 tons per 24 hr. In 1936 the property was again closed owing to labor trouble, a drop in the price of silver, and increased water in the mine.

Jan 10, 1957

Bethlehem Steel Co. has just brought an all-new iron ore mine into production at Marmora, Canada, about 120 miles east of Toronto. High grade pellets produced at the mine from open-pit magnetite ore travel 64 miles by rail to the port at Picton, then go by Lake boat to help supply Bethlehem's Lackawanna, N. Y., plant. At full production about half a million tons of pellets a year will be shipped, and mining will be at a scale of more than a million tons per year of ore. Aeromagnetic surveys carried out in 1949 by the Ontario Dept. of Mines and the Canadian Geological Survey revealed an anomaly that interested Bethlehem geologists. By 1951 the company had put down some 40 diamond drillholes ranging from 460 to 1800 ft to block out the magnetite replacement deposit which lies in pre-Cambrian limestone below about 130 ft of Paleozoic limestone. The orebody, roughly 2100 ft long and up to 400 ft wide, averages about 37 pct iron, too low for direct shipment. Not only construction of concentrating and pelletizing facilities, but 20 million tons of stripping lay ahead before production could start

Jul 1, 1955

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By William Fink

APPROXIMATELY two years ago the authors obtained data that indi-cated that initial precipitation could not be detected by change of lattice parameter in the aluminum-rich aluminum-magnesium alloys. Some of these data were first published in a brief note in MINING AND METAL-LURGY1. Cast specimens were used at that time and they showed initial precipitation relatively sooner than sheet material of the sane composi-tion. For this reason a more thorough investigation has been carried out using a homogenized aluminum-magnesium sheet containing approxi-mately 10 per cent magnesium. Materials.-The aluminum used in the preparation of the aluminum-magnesium alloy was of high purity, containing less than 0.01 per cent each of iron, silicon and copper. The magnesium was high-purity sub-limed magnesium. Preparation of Alloy.-Approximately 4 kg. of the aluminum was melted in a plumbago crucible in an electric furnace and the magnesium was added. The melt was thoroughly stirred with a graphite rod and fluxed with chlorine gas before casting. The alloy was cast in the form of a sheet ingot in a cold iron tilting mold (approximately 200 by 165 by 40 min.) and into small chill-cast, slabs for chemical analysis (75 by 40 by 5 mm.). The chemical analyses were made upon drillings from the analysis slabs. The analytical methods were those described in "Chemical Analysis of Aluminum," published by the Aluminum Company of Amer-ica. The composition of the alloy was found to be: magnesium 10.30, silicon 0.013, iron 0.008 and copper 0.005 per cent.

Jan 1, 1936

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By W. H. Bassett

IN their paper on the directional properties in cold-rolled and annealed commercial bronze,1 Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45° ears" and "90° ears. " Fig. 1 shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45° ears, while that annealed at 950° C. showed FIG. 1.-CUPRONICKEL, 0.032-in. GAGE, CAST WITH MAGNESIUM. ANNEALED AT TEMPERATURES INDICATED (DEGREES CENTIGRADE) AND CUPPED. long "90° ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be.

Jan 1, 1932