Search Documents

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By W. O. Philbrook

ALTHOUGH the actual output of about 89 million tons fell a little short of the hopes and more optimistic predictions of the beginning of 1943, the American iron and steel industry last year produced the record tonnage of its history. It was sufficient to catch up somewhat on the crucial needs for prosecution of the war though an excess of demand over available supply of steel still persists in most categories. It will be necessary during the coming year for the operators to continue to devote all of their efforts and ingenuity to obtaining the utmost tonnage both from existing units and from new facilities still to be brought into production.

Jan 1, 1944

After the explosion in the Black Heath pit, that company sent to England for some experienced miners to reopen the mine. The results of their work in this vicinity are mentioned in an advertisement for pit hands by the Mid-Lothian Co., as follows: "PIT HANDS WANTED.-In consequence of reports having been circulated of the insecurity of hirelings in the Mid-Lothian Mines, the Company deem it proper to make known, that the mines have recently been opened, and that not the slightest explosion from gas has occurred; the workings were laid out and are now progressing, ° under a plan furnished by Messieurs Foster & Hall, .two distinguished English Colliers, sent over from England to reclaim the Pits of the Black Heath Company after the recent explosion of gas-and the present under ground operations are now conducted under the management of one of the English foremen left here by these gentlemen, and supervised by Mr. Wm. Hall, who has under his superintendence the Black Heath Company's Works at present. The skill and capacity of those gentlemen, is fully evinced in their skilful reclamation of the Black Heath Mines, and their present successful working of said Pits; and their confidence in the safety of the hands in the Mid-Lothian Mines, will be seen, by reference to the annexed extract from the Plan left by Messrs. Foster & Hall for laying out and working the Mid-Lothian Mines, and from the Certificate of Mr. William Hall, as to the manner in which that plan is carried into effect. This publication has been deemed proper, as the Company are now in want of some ten or fifteen additional able-bodied, active Pit-hands, on hire by the year, for which they will give the most liberal hire. The Company have not hitherto spared any labor or expense, deemed necessary to secure the absolute safety and comfort of the hands in their mines; nor is it designed in future to omit any thing that can add to the security of their own hands, or the hired laborers of other persons-indeed they can, with great propriety, say, as far as they have progressed, that no mines in this country exhibit stronger, if as strong, evidence of general safety. The Company will receive on hire, no hands who do not voluntarily enter their service -and they request of those having hands to hire out, to remember that they will want upon hire, successively, at intervals of every ninety days, some additional four or five hirelings during the year, or to purchase, progressively, that number of healthy, able-bodied young men. "Owners of slaves at a distance from the Coal Mines, would do well to give some attention to the subject. There is no place in this country where slave labor commands as much, where their general health is better, and where the treatment and contentment of the slaves are surpassed. It is true that within the last few years several disastrous accidents have occurred, but from the scientific and practical skill attracted to the mines, these accidents will be of rare occurrence, it is to be hoped. A. S. WOOLDRIDGE, President, at the Mines in Chesterfield County.

Jan 1, 1942

By Bieniawski, Z. T.

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years. These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today.

Jan 1, 1972

IF you wish to make the acid that is vulgarly called common aqua fortis,* for parting gold from silver, you must first provide as many cucurbits and alembics, receivers, and materials as you wish, and then make a furnace that is long and conveniently wide for holding three or four pairs of cucurbits or as many as you wish. If you have to make this by art in order to work a large quantity, you could make several small furnaces for it seems that not more than three or four pairs are suitable for one. Prepare the places where the cucurbits are to stand with bottoms or covers made of potter's clay or tiles that are half round like the bottoms of the cucurbits and have a little rim around the top so that they can be built in. Proceed to build these in in pairs, one by the other with convenient spaces between, placing an iron support across to make this place stronger and more secure. In every corner and also in the middle a hole must be made as a vent for the smoke, as is done in all furnaces. You will see the form of this somewhat roughly drawn here. [Figure 25] Near this prepare a number of cucurbits which are made of glass, as clear and uniform as possible and very well formed. There must be no bubbles or other indentations in these, for they would be dangerous and uncertain for your work. Lute these with lutum sapientiae up to within three dita or less from where the neck narrows. This lute must be spread out well all over to the thickness of two threads or a little more. Then cover and make them strong with this well-made plaster, and finally dry it, taking care that there are no clefts or cracks such as clays are often prone to make even though they be well prepared. For greater security choose among these [64v] a clay that is lean and then mix it with at least a fourth part or more of wool-clloth clippings and about an eighth part of wash

Jan 1, 1942

By John B. Hastings

THE occurrence of such a large amount of gold in the Hartsel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of magmatic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities graunitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of San Juao de Chapado, Brazil, described by Derby :1 (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the. diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition." (P. 143) "The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists. . . . The recent studies . . . seem to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says ". . . veins or dikes-it is an open question which is the more correct term-are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters. . . . In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 5, 1908

By N. K. Chen, R. Maddin

Single crystals of molybdenum were extended at temperatures from 1300° to 2500°C. It was found that with increasing temperatures, the yield becomes more pronounced and the number of slip bands for equal amounts of elongation decreases. Slip at high temperatures fragments the structure. OTHER than the investigations on sodium and potassium by Andrade and Tsien,&apos; the researches of Steijn and Brick&apos; on a iron single crystals at low temperatures are about the only studies of the influence of temperature on glide of body-centered cubic single crystals. The effect of test temperature on glide has been rather widely investigated with hexagonal crystals" and less widely with face-centered cubic crystals. ~~ a result of these studies it can be said that, in general, the onset of plastic flow as measured by the initial rate of strain hardening becomes more abrupt with increasing temperature, and the value of the yield decreases with increasing temperature. Strain hardening, however, is markedly affected by changes in temperature except at very low and very high temperatures where the strain hardening rate becames constant. In the present investigation it is shown that temperature affects the glide of molybdenum single crystals in much the same manner as crystals of other classes, it., for comparable strains the number of slip bands decreases with increasing temperature; shear along the slip bands increases with increasing temperature; the yield becomes more pronounced with increasing temperature of test; and the strain hardening approaches a constant at very high temperatures. In addition, it is shown that, in agreement with the work of Tsien and Chow, Qlip occurs on (110) planes in <Ill> directions. It is further shown that slip at high temperatures fragments the structure into either irregular sized cells or bent atomic planes which are roughly aligned in crystallographic directions. Experimental Procedure Single crystals 3 mm in diameter by about 25 mm long were prepared using the technique previously described.&apos; The furnace in which the crystals were grown served as the extension apparatus for the tension tests. It consisted of a 4 in. water-cooled brass tube 20 in. long which was continuously evacuated at the bottom. Two water-cooled copper electrodes held the specimen by means of spherical collets secured in place in the electrodes by set screws. These electrodes served also to transmit power and stress to the specimen. The lower electrode was clamped to a stand, while the upper electrode was fastened to one side of a lever arm flexibly supported at the top through a slightly offset pinion. A metal bellows operating elastically was attached to the upper electrode to affect a vacuum seal and allow freedom of motion. The level of the arm was adjusted by rotating a graduated nut. Rotation of the electrode was prevented by a key fitted into a groove. After the specimen was mounted and the vacuum secured, the lever arm was adjusted so that the bellows was at its relaxed position. This insured that the total weight of the specimen, the upper electrode, and the downpull of the vacuum were balanced by the horizontal beam. Since the specimen was heated by its own resistance, expansion of the specimen proceeded freely by this arrangement. During the time of heating the specimen, the beam was maintained in a horizontal position by turning the nut at the top. By graduating the lever arm and using a known dead weight on the lever arm to supply a tensile stress, the graduated nut could be read to 0.0001 in. extension. Since

Jan 1, 1955

By AIME AIME

ALL 32 of the Local Sections of the Institute in the continental United States and practically all of the Divisions as well, had representatives present at the Conferences of Local Section and Division Delegates at the Annual Meeting. Three sessions were held, two on Monday and one on Thursday, both the incoming and outgoing Presidents of the Institute being on hand to con- duct the meetings. H. J. Brown was called to the chair during a portion of the last session, President Fulton having to leave early. Complete minutes of the meetings have ,been sent to all delegates. In general, the Local Sections appeared, from their reports, to have risen to the wartime demands made upon them with their usual resourcefulness. Apparently more difficulty has arisen in the last year in arranging attractive programs and securing acceptable speakers, this being perhaps attributable to the fact that most technical men have been extremely busy. Careful planning ahead .has usually brought good results, however. Another wartime difficulty has been the matter of transportation to meetings, gasoline rationing and congestion on the railroads and buses being a handicap to attendance. Sharing cars has proved practical as a method of meeting this issue, this again requiring planning. Suitable meeting places and a supply of food have been another difficulty for some local groups.

Jan 1, 1944

By John Jermain Porter

(San Francisco Meeting, October, 1911.) THE value of any particular ore, coke, or limestone, for iron-making, depends upon its effect, first, upon the quality or value of the resultant product; and second, upon the cost of smelting. The factors under the first head are the percentages of phosphorus, manganese, and other elements, which remain in the pig-iron ; while those under the second head are the percentages of iron, carbon, or lime, the slag-forming constituents, which must be fluxed, and any other ingredients which give rise to variations in cost of fuel and flux. The first of these criteria of value is perhaps not capable of being reduced to a general formula embracing all cases, since it must vary to a great extent with market-fluctuations. For example, Bessemer pig is worth sometimes more and sometimes less than foundry-pig ; and the premium paid for high manganese varies within wide limits. The second, or smelting-value, however, can be expressed numerically with a fair degree of accuracy; and it is with this phase of valuation that the present paper is concerned. The utility of a means of comparing numerically the relative smelting-values of different ores, cokes, and limestones, is self-evident, although it may not have importance in Northern practice, where materials are largely standardized. On the other hand, there are, especially in the South, many furnace-managers who must use a great variety of materials of widely varying grade; and it is with special reference to this district, and in connection with the efficiency-methods which I have elsewhere proposed,1 that the methods herein described were devised.

Mar 1, 1912

By O. Hall, V. P. Row

Diamond drilling has become a very important factor in mining. It is the most satisfactory method of obtaining proof of the existence of an orebody and of determining the character and extent of the body in measures where a core can be made. Large investments are based on the information obtained. The method of development, the mine and reduction plants, and subsidiary essentials established are often without other information. The Mond Nickel Co. has drilled about 50,000 ft. (15,240 m.) per yr. for sevéral years and has given considerable study to the question of improving the methods and of overcoming the limitations of this means of securing information. One of the main limitations of the diamond drill has been its inability to drill a straight hole. To depths of 1000 ft. (304 m.) the deflection is often not large but all holes tend to curve and take somewhat erratic courses. A hole running at a small angle to a fissure plane tends to run along the fissure. If the hole is at a large angle, the tendency is to penetrate the fissure plane at right angles. The face of the bit having one side in solid formation beyond the fissure, the other in the selvage of the fissure, tends to turn, the rods curving to the extent of their clearance in the hole. Usually rock measures have somewhat regular fissuring or strata and holes take somewhat similar courses, usually at right angles to the fissuring or strata. Excessive pressure or short or worn core barrels increase curvature. Slow speeds, correct feeds, sharp bits, and core barrels the full size of the bit, tend to decrease curvature but do not prevent it Curvature once started increases rapidly. The disappointments from crooked holes have been numerous. Discoveries have later been found to be on the properties of others. One Canadian company had a hole, supposedly discovering ore 300 ft. (91 m.) from old workings, unexpectedly turn in 8 ft. (2.4 m.) of wooden core from a timber in the old workings. In many cases the information secured by a curved hole is satisfactory, if it can be accurately surveyed. The inclination of the hole at any point

Jan 1, 1920

By William P. Dyrenforth

The principle of electrostatic separation is discussed and elaborated on by dividing into the three main mechanisms of electrification as applied to separation of solid substances, i.e., (1) contact electrification, (2) electrification by conductive induction, (3) electrification by ion bombardment. Types of equipment used for electrostatic processing are described and the effects of humidity mentioned. Processing of iron ore, titanium minerals, rare earths and cassiterite is discussed and some existing plants are described.

Jan 1, 1978

By W. C. Snow

The plant of the Electrolytic Zinc Company of Australasia Limited, situated at Risdon on the estuary of the River Derwent, near Hobart, was designed and erected primarily to produce high-grade zinc from zinc concentrates produced by the mines of Broken Hill, N. S. W. Consequently the metallurgy of the process has been influenced in its development by the peculiar characteristics of the Broken Hill concentrate, which on treatment gives into solution relatively large amounts of cobalt, manganese and silica. The Risdon works (Fig. 1) produces high-grade electrolytic zinc, leaded electrolytic zinc, zinc dust, cadmium, sulphuric acid and superphosphate. This paper, however, is concerned only with the zinc plant and process. Roasting The roasting of raw concentrate is not a major feature of Risdon&apos;s process, and in this respect practice is unlike that of most zinc plants. The roasting is mostly done on the Australian mainland at centers where the sulphuric acid made from the roaster gases can be used for superphosphate manufacture. A small amount, approximately 40 tons per day, is roasted at Risdon, acid being manufactured from the gases. The amount that can be roasted there is limited by the acid requirements of the zinc plant and of the superphosphate plant. Roasting is not carried to completion at the mainland plants, and the product, known as preroast calcine, largely constitutes the raw material for the Risdon zinc plant. It contains about 6 per cent of sulphur as sulphide. Roasting is completed at Risdon for reasons that are set out later in this paper. The zinc plant proper is divided into four main divisions: (1) final roasting division, (2) leaching and purification division, (3) electrolytic division, (4) melting and casting division. There are two subsidiary divisions—the cadmium division and the preroast, acid and superphosphate division.

Jan 1, 1937

Jan 1, 1971

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

By Samuel L. Hoyt

This paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use. The samples used were 5 to 6 mils thick and about 1 in. square. They were placed between iron blocks and set in the hot zone of a nichrome furnace which had been brought to the desired temperature Time was taken from the moment the samples reached the furnace

Jan 1, 1929