Search Documents

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower. Local tipped drill steel was adopted for all mine drilling in November 1951. Since then drilling costs per foot have been sharply reduced and footage drilled per manshift has increased markedly. Experience at Flin Flon has shown that production of satisfactory carbide tipped drill steel is not difficult and that highly skilled labor and costly equipment are not required. As long as wise selection of brazing materials is made and certain simple precautions are rigidly maintained, there is no reason why small mines with relatively unskilled labor cannot produce a satisfactory product. The following description outlines the technique used at Flin Flon for making carbide tipped drill steel and discusses characteristics of the brazing process that make special precautions necessary. Drill steel is forged to four-wing shape in a conventional steel sharpening forge. Standard steel dies are modified to minimize forging cracks around the central waterhole and to forge a blunt bithead on the steel. The steel is preheated to 1500°F and held at this temperature for at least 2 min. When the temperature has equalized throughout the steel section, the drill steel is transferred to the forging furnace and heated rapidly with a reducing flame up to 2000°F. This two-stage method of heating minimizes the grain growth and decarburization of the steel while ensuring that the steel temperature does not vary greatly throughout the forging zone. After forging the steel is allowed to cool in air to about 1600°F before being annealed in a bath of vermiculite. Despite the high hardenability of the 3 pct Ni-Cr-Mo drill steel used, this simple treatment anneals the drill steel sufficiently for milling. The forged and annealed drill steel is slotted on a plain horizontal milling machine that is equipped with a quick opening chuck and a slot depth stop. The full depth of the slot is milled in a single pass of the 3-in. milling cutter which is fed at 33/4 in. per min across the crown of each bit wing. The slots are cut to a width of 0.342 to 0.344 in. Maintenance of this slot width is necessary to ensure that the optimum brazing clearance of 0.002 in. will result after assembling of shims and carbide in the slot. Prior to March 1953, when the milling machine was installed, drill steel was slotted on a small manually fed ¾ hp milling attachment mounted on the bed of a lathe. Over 16,000 drill steels were slotted on this unit, and in view of its small size and low cost it gave excellent service. Brazing of Tipped Steel Drill steel that has been milled and cleaned in carbon tetrachloride is mounted in a rotating cradle holding six drill steels, the length of which may be from 2 to 12 ft. The slots in the drill steel, the shims, and the tungsten carbide inserts are thoroughly fluxed with a fluoride flux and assembled as shown in Fig. 1. Fig. 2 shows the brazing equipment in use. As the ring burner is lowered over the bithead a spring valve opens the gas lines, and the gas mixture, preset to give a slightly reducing flame, is fed to the ring burner where it is lit from a pilot flame. The ring burner heats the drill steel over a zone about 1 to 2 in. below the bithead, which becomes heated by conduction through the steel. By this means the bithead is heated rapidly and evenly, and contamination of the brazing joint with soot from the flame is avoided. The bithead is heated to the melting temperature of the brazing alloy within 1 min. This rapid heating minimizes the disadvantage of a non-eutectic brazing alloy. The brazing alloy, a nickel-bearing quaternary alloy, is placed at the bottom of the slot below the carbide insert, as shown in Fig. 1. As the brazing alloy melts it is drawn by displacement by the carbide and by capillary action into all parts of the joint to displace liquid flux from metal surfaces. As soon as the brazing alloy melts, each insert in turn is wiped by being moved back and forth along the slot. This action assists wetting of the carbide by the brazing alloy and assists in displacing molten flux from the joint. After continuous heating for about 75 sec, when the bithead has reached a temperature of about 1500°F, the ring burner is raised and the gas supply is shut off automatically by the spring valve. As soon as heating is stopped a hand press is placed on the bithead and the inserts are squeezed down firmly. This action minimizes the clearance between the bottom of the insert and the slot. Correctly brazed steel should maintain a clearance at the bottom of the slot of 0.001 to 0.002 in. After six steels have been brazed they are removed from the cradle and allowed to cool in air. As soon as each drill steel is cool it is dressed on a grinding wheel to remove excess flux and braze and is ground to the gage appropriate to the length of the drill steel.

Jan 1, 1955

By J. B. Cheatham, J. G. Yarbrough

Although adequate removal of cuttings from beneath a drill bit is important for efficient drilling operations, very little basic data are available relative to the fundamentals of chip removal by hydraulic jets. A discussion is presented in this paper of an experimental investigation of the jetting action of hydraulic jets in removing loose particles from the bottom of a cylindrical hole. Conditions for which the jet is no longer capable of removing chips from the bottom of the hole are determined. This situation represents equilibrium between the chip removal force and chip Bolddown forces such as gravity and pressure. In most of the tests loose particles were jetted with water or a water-glycerine mixture to determine the dependence of chip removal on hole size, jet size, height of jet off bottom of hole, flow rate, particle density and fluid viscosity. ,A test with a pressurized mud system indicated that relatively low pressures can completely overcome the removal action of a hydraulic jet. Although the system studied herein is not directly applicable to a rotary drill bit, the work with such simplified systems can provide a better understanding of the chip removal action of jets, and with logical extensions it may provide a reasonable basis for the best use of fluid jets in drilling. INTRODUCTION The primary deterrent to maximum drilling rates is the inability of the drilling system to remove rock cuttings efficiently enough to prevent interference with the drilling action.1-2 The objective of chip removal studies is to permit predicting and controlling removal forces under downhole drilling conditions. Conditions at the bottom of a hole during rotary drilling are exceedingly complex and are not likely to be described in a quantitative way by investigations in terms of the total drilling action until a better understanding is developed of the simplified components of the problem.3 The present study is concerned with the elementary condition of removal of chips by a single central jet. Even this relatively simple model provides mathematical difficulties because of the turbulent nature of the flow from the jet and because of the shape of the bottom of the hole beneath the jet. Theoretical and experimental studies have been made of turbulent jets impinging normally on an infinite body and deductions based on analytical solutions to simplified problems can give some insight into the problem of cutting removal by a jet. However, because of the present lack of understanding of the behavior of the interaction between the fluid jet and the chips being removed, an experimental approach was chosen for the present study. Methods have been developed for maximizing hydraulic horsepower, impact force and jet velocity; but whether maximizing these parameters maximizes chip removal with present drilling bits has not been demonstrated. Simplifying the problem of chip removal may make it possible to develop some understanding of the manner in which the jet velocity is dissipated. Better understanding of a simple case should materially assist in extending analysis to more complicated cases. Thus, we are not concerned in the present study with the rock fracturing process itself but only with the removal of the debris from the bottom of the hole. A problem which is quite similar to the chip removal problem is the suspension of solids in stirred vessels. This problem has been studied by the chemical industry and correlations have been obtained by dimensional analysis which permit the design of mixing vats7 An approach similar to that used in the mixing vat problem is used in the analysis of the jetting data in the present paper. EXPERIMENTAL PROCEDURE The test equipment arrangement shown sche-matically in Fig. 1 allows the jetting action to remove particles until an equilibrium height is attained for each combination of hole size, jet size and flow rate.*** Equilibrium conditions require that the removal force is unable to remove additional particles. This balance between holddown and removal forces implies a relationship between the two forces which is constant for the particular system. When the holddown forces are constant,

Jan 1, 1965

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919

By Charles H. Fulton

(Cleveland Meeting, October, 1912.) I. INTRODUCTION. THERE are comparatively few accurate data on the melting-or the freezing-point temperature of metallurgical slays, or on related physical phenomena, such as fluidity near the melting-point, specific heat, latent heat, etc. With the exception of the work of H. 0. Hoffman,1 and some older work by R. Akerman, P. Gredt, and H. M. Howe, no information is available that is of direct interest to the metallurgist. Hofman's valuable work is the only one that refers to slags produced in the metallurgy of copper and lead. The classic work of J. H. L. Vogt,2 who views slays from the standpoint of physical mixtures (solutions in which the entities are minerals), has opened up a. new field in the study of slags, and has placed the investigation of such properties as melting-temperatures, etc., on a rational basis. The recent work of A. L. Day, E. T. Allen, and W. P. White, of the Carnegie Institution, at Washington, and of European investigators 3 on certain systems of silicate minerals confirms the value of the investigation of silicate series from this standpoint, and it is my aim to apply this method to metallurgical slaws, in order to gain exact data of value in metallurgy. The work recorded in the present paper is the result of an investigation of reverberatory-furnace slags made for a Western smelting company to determine exactly the influence of change in composition, within comparatively narrow limits, on the melting-point. For a general discussion concerning the mineralogical character of slaws and the principles on which this investigation is based, reference should be made to other work,4 for the subject is too large to be stated in this paper, except very briefly in the following outline 1 Trans., xxix., 682 (1899). 2 Die Silikatschmelzlösungen; I. Ueber die Mineralbildung in Silikatschmelzlösungen; II Ueber die Schmelzpunkt-Erniedrigung der Silikatschmelzlösungen (Christiania, 1903-04). 3 Doelter, Handbuch der Mlineralehevu:e (1911) 4 C. H. Fulton, Principles (of Metallurgy. Chapter viii., on Slags, p. 24.5 (1910).

Dec 1, 1912

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

Organization Place Date 1919 American Electrochemical Society New York, N. Y. Apr. 3-5 American Chemical Society Buffalo, N. Y. Apr. 8-11 National Foreign Trade Council : Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y: May American Institute of Electrical Engineers Lake Placid, N. Y. June 23-27 American Society for Testing Materials..: Atlantic City, N. J. June 24-27 American Railway Bridge and Building Association Cleveland, O. Oct. 21-23

Jan 4, 1919

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

CONTENTS PAGE GEISMER, H. S.-Coal Washing Practice in Alabama. Discussed by William Kelly, H. S. Geismer, H. D. Pallister, L. E. Bryant, Milton H. Fies, Elmer F. Harris, James A. Barr, George G. Crawford, E. C. Wright, George S. Rice, R. V. Norris 1 MILLER, F. W.-Byproduct Coking in Alabama. Discussed by Theodore Swann 4 FIES, MILTON H.-Alabama Coal Mining Practice. Discussed by Milton 11. Fies, R. V. Norris, R. D. Hall, L. E. Bryant, George S. Rice, H. S. Geismer 5 MUSSEY, H. E.-Blast-furnace Practice in Alabama. Discussed by C. A. Meissner, Franklin H. Crockard, H. E. Mussey, W. H. Oldham 14 Coal Washing Practice in Alabama Discussion of paper of H. S. GEISMER, presented at the Birmingham Meeting, October 1924, and issued, as Paper No. 1363-C, with MINING AND METALLURGY, September, 1924. WILLIAM KELLY, Iron Mountain, Mich.-Is the dry-cleaning method used? H. S. GEISMER.-Neither the dry-cleaning process nor the Chance sand-liquid method has been tested in Alabama; but all other methods used for cleaning bituminous coal have been largely brought to perfection in this state. H. D. PALLISTER, Tuscaloosa, Ala.-Have you the results from the recent work on the tables with reference to fine coal? H. S. GEISMER.-None of the iron-producing companies has adopted the tables, though three commercial operators have installed tables within the last six months. I tried to learn the results, but they were not willing to release the data just now. At the mines producing domestic coal, fines present a difficult problem; until within the past six months all the fine coal was wasted. The operators are trying to recover some of it on the table. L. E. BRYANT, Rockwood, Tenn.-Is there any connection between the sulfur content of the sludge and the effect of the sludge on vegetation?

Jan 7, 1925

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) The position of converter blower at a side-blow Bessemer steel casting plant is vacant. The State Legislature of Utah has provided for the establishment of a metallurgical research department at the State School of Mines, Salt Lake City. Applications will be received for, the position of head of this laboratory, and further details may be obtained by applying to Prof. Joseph F. Merrill, Director, University of Utah, Salt Lake City. An engineering company owning patents for improvements in steel manufacture which have been adopted at many works in America, desires. to secure the services of a technical iron and steel metallurgist as assistant to its chief metallurgical engineer.

Jan 6, 1913

By A. Szirmae, Hsun Hu

The early stages of recrystallization in a 70 pct cold-rolled Si-Fe crystal of the (110) (0011) orientation were studied with a Siemens electron microscope. Orientation studies based on electron-diffractzotz. patterns confirm the results of previous texture analysis. The driving energy for recrystallizatior and the critical radius for growth were calculated from the dislocation energy and the energy of the subgrain bourzdaries, and it was found consistent with the observed size of the recrystallized grains. The recrystallization characteristics of crystals with different initial orientations are discussed. The recrystallization of cold-rolled (110)[001] crystals of Si-Fe has been widely studied by various investigators.1-4 Their results on both deformation and annealing textures are in good agreement. The rolling texture after 70 pct reduction consists mainly of two crystallographically equivalent (111) [112] type textures and a minor component of the (100) [011] type. The latter is derived from the deformation twins, or Neumann bands, which are formed during the early stages of deformation and later rotate to the (100) [011] orientation upon further rolling reduction. Between the two main (111) [112] type textures, there is some orientation spread, because of which very low intensity areas appear in the pole figure. If these very low intensity areas are considered to be a very weak component in the texture, then a (110) [ 001 ] orientation may be assigned to them. When this rolled crystal is annealed at a sufficiently high temperature for recrystallization, the texture returns to a simple (110) [001]. The purpose of the present investigation was primarily to seek a better understanding of the recrystallization process by using the electron transmission technique. The (110) [0011 type of crystal was selected because orientation data for it are well known from previous studies with conventional techniques. Direct observations on the recrystallization of such a crystal have also been made by using a hot-stage inside the electron microscope, and the results will be reported in another paper. MATERIAL AND METHOD A single-crystal strip of the (110) [001] orientation was prepared from a commercial grade 3 pct Si-Fe alloy by the strain-anneal technique.= The strip was approximately 0.014 in. thick, and was rolled 70 pct at room temperature to a thickness of 0.004 in. Specimens were cut from the rolled strip and were annealed in a purified hydrogen or argon atmosphere. They were then electrolytically polished in a chromic-acetic acid solution to very thin foils. Best results were found by polishing first between two narrowly spaced flat cathodes with the specimen edges coated with acid-resisting paint, followed by polishing between two pointed electrodes until a hole appeared in the center as described by Bollmann.6 It was found that a thin transparent film always formed along the thin edges of the polished specimen. This film was then removed by rinsing the specimen very briefly in a solution of alcohol with a few drops of HF or HCl. RESULTS AND DISCUSSION 1) The Deformed Crystal. From the electron-diffraction patterns taken at various areas of an as-rolled specimen, the texture components as deduced - from ordinary pole-figure analysis were confirmed. Over most of the areas where orientation was examined, a (111) pattern with a [112] direction parallel to the rolling direction was obtained. This corresponds to the main deformation texture of the (111) [112] type. In a few areas the diffraction pattern was (100) [Oil], corresponding to the minor-texture component derived from the Neumann bands. The (110) [001] orientation, which corresponds to the very weak intensity area in the pole figure, was found infrequently. A typical example of the deformed matrix having the (111) type main texture is shown in Fig. 1, where (a) is the microstructure and (b) is the diffraction pattern taken from that area. It was also frequently observed that in other areas more or less continuous rings of weaker intensity were superimposed on the simple (111) diffraction pattern, suggesting the presence of a wide range of additional orientations. Other evidence indicated that the recrystallization characteristics are different in these two different types of areas. The hot-stage observations which provide this evidence will be discussed in another paper. AS shown in Fig. l(a), numerous dislocation-free areas of very small size are embedded in the "clouds" of high-dislocation density. This indicates that the deformation of a single crystal, even after a rolling reduction of 70 pct, is far from uniform on a micro-

Jan 1, 1962

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position in sales department is open for a mining engineer with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions. No. 2. A large company manufacturing mining machinery has an opening in one of its Western agencies for a young mechanical engineer who has had some experience in designing along general machine shop lines, and who is familiar with cost systems. No. 3. A large university desires to secure a prominent metallurgist for a vacant professorship in metallurgy. No. 4. Opening at a mine in New Jersey for a technical graduate to begin work as chairman on the surveying squad. Salary $50 per month to start. No. 5.

Jan 11, 1913

By L. G. Austin, R. R. Klimpel

This article demonstrates that the Gilvarry and Klimpel-Austin equations for the random fracture of solids are incorrect by deriving intuitively correct expressions for simple cases and showing that the foregoing equations do not reduce to right answers. It is the purpose of this article to point out serious errors in some existing treatments of the random fracture of solids. Gilvarry ' gives the equation where B(y,x) is the cumulative fraction by weight of particles which fall below size y when particles of size x are broken. The constants i, j, k contain shape factors and densities of flaws leading to propagating fracture surfaces. The authors believe this equation to be incorrect. Klimpel and usttin' give where r~ is the number of fracture planes originating from edge flaws (per L where L is the edge length of the original particle), rs is the number of fracture planes originating from flaws on the particle surface (per S where S is the surface of the original particle) and rv is the number of fracture planes originating from flaws within the particle volume. This equation is also incorrect. The failures of these equations will be demonstrated by deriving intuitively correct expressions for simple cases and showing that the Eqs. 1 and 2 do not reduce to the correct answer. In this process, the flaws in statistical reasoning inherent in the derivations of Eqs. 1 and 2 become apparent. THE KLIMPEL-AUSTIN EQUATION Eq. 2 was derived by considering a set number of fracture planes occurring spatially at random within a given particle. This case will be treated here in its simplest form: a line with 1, 2, 3, etc., fractures occurring at random. This is illustrated in Fig. 1, with the original length of the line as Vo. The breakage of a long, thin, brittle fiber is a corresponding physical case, with the volume of a fragment proportional to its length. Assuming independence of the occurrence of the fractures, the probability of any one fracture occurring in length dV is dV/V0. The probability of the first fracture occurring at a length V to V + dV is dV/Vo. For the case of only one fracture per particle, formation of a number-size distribution of the left-

Jan 1, 1969

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By D. W. Mitchell

INE operators have a choice of several classi- fications of mechanical loaders. Within each classification there are many types and makes available. Table I lists loaders on which manufacturing data as to operating characteristics are available. This paper discusses the conditions met in a mine as they affect these characteristics. It is assumed that management will provide satisfactory engineering, supervision, power, maintenance, loader service within a concentration of workings, and a balanced working cycle served by balanced production equipment. These are factors which affect the optimum operational efficiency of a loader. The conditions which determine loader choice are: Height of Vein—The main limitation to the use of a loading machine is the height to which the vein is mined; i.e. a loader cannot be higher than the place in which it is to work unless rock is taken. Since there are several low vein loaders being developed and successfully applied, this does not appear to be a requisite of an efficient mining operation. The maximum useable height of a loader should be equal to the working seam thickness less a working clearance for travel and operation. A—Working seam thickness = B—Artificial roof support thickness = C—Safe headroom below support = (generally about 6 in.) D—Height of roadway = E—Total of B + C f D =_______________________ A—E = maximum loader height F—Distance from top of roadway to bottom of roof support = G—-Height of loader's coal or ore line (see Table I) = H—Difference between F and G = Size of largest broken particle + a safety factor of 2 to 3 in. H is a loadability factor and is important because the clearance over the top of the conveyor chain to the roof or roof support must be greater than the largest broken particle or else the particle and/or the conveyor chain may be broken. From this standpoint it might be desirable to use a lower height machine even though it may have a smaller capacity, though this is warranted only when increased lump realization offsets lower man-day and machine pro- duction rates. Ivan Given has stated, "Loading should not be handicapped by securing lump only to grind it in the breaker." Width of Working Place—The width of a working place is the greatest width a place may be safely driven. The working place includes not only the face but the roads the loader must tram when mucking out more than one face. The width is limited by the system of placing props with sufficient room between them for the machine runner (about 2 ft). Maximum width of place in which the loader will operate at maximum efficiency is determined by the type of mounting. With track-mounted loaders, maximum width of place is determined by maximum angular swing of the loading head and proximity of track to the face. The use of double track leads to added expense and operational complexities. Several mines that have used double-track systems have found that a substantial saving is made by the use of machines that load out wider places. Trackless loaders may work in rooms of any maximum width. Minimum width of place in which a loader will operate is determined by width of the loader plus a safe movement area for the operator. Often a barodynamic study of the mine will show that either an increase in room width and/or a change in the system of propping may be made by using roof bolting, full or part-width room timbers, removable aluminum I-beams at the face, etc. Increasing the width of a working place will, in general, increase loader operating efficiency by providing more material per fall and by decreasing the preparation and moving time per ton. A change in the system of propping that would increase the minimum width might permit the use of a higher capacity loader with safer working conditions. Proper face tirnbering is necessary to insure safety from roof falls and because the speed of preparation and loading generally increases since the men work with greater assurance and there is less chance of kicking out posts. Maximum Room Length—With the exception of the scraper and the duckbill, the limit to room

Jan 1, 1952

By Rex B. McLellan

A simple model for dilute interslitial solid solutions is set up which enables a solubility equation for the equilibrium between the solid solution and the gaseous solute to be deduced. This solubility equation is used to estimate the partial thermody -namic functions of Ag-O and Fe-N dilute interstitial solid solutions from the measured equilibrium between these solutions and the gas phase. It is shown that the partial excess entropy of the solute atom in solution is a vibrational entropy which is due Principally to the oscillation of the interstitial atom and does not arise from electronic or elastic interaction between the solute atoms and solvent matrix. In this work measurements of the equilibrium between dilute solid interstitial solutions and a gaseous phase are used to deduce the important thermody-namic functions of the solid solution with the aid of a theoretical solubility equation formulated from a knowledge of the thermodynamic functions of the gas and a simple model for the solid solution. The quantity of principal interest which is deduced from the equilibrium data is the change in vibrational entropy occurring when a solute atom (u) is placed in an interstial site in the solvent (u) lattice. This paper forms part of a more general study in which the properties of condensed phases are deduced from measurements of the equilibrium between the condensed phase and a gas. Previous investigations have dealt with the equilibrium between krypton and liquid metals,' a pure metal and its vapor,' and dilute substitutional alloys and the vapor,3 and the subject has been popularly reviewed by McLellan.4 In the latter investigation3 the vapor pressures of very dilute Cu-Ag and Cu-Au alloys were measured with a Knudsen cell technique over a large range of temperatures and the analysis of the vapor-pressure data showed that the relative partial excess entropies were large and positive [ds= -Sudk = 30 for Au-Ag alloys and 150 for Cu-Au alloys; these values should be compared to unity, the value assumed for these exponentials in the quasi-chemical theory of solutions]. For many interstitial solutions experimental data is available for the equilibrium between the solution and a gaseous phase, and this can be used to deduce the vibrational entropies of the solute atoms in solution. The general method employed is to calculate the chemical potential of the solute atoms in the gas and equate this to pi, the chemical potential of solute atoms in the solid, which is deduced from a simple model set up for the dilute interstitial solution (in which the solute atoms act as bound oscillators in interstitial sites). This enables a theoretical solubility equation to be set up. In the case of Ag-O and Fe-N solid solutions the solubility c, is found to vary with temperature according to a relation of the type, where PU2 is the pressure of the O2 or Np molecules. Essentially, the theoretical solubility equation enables the parameter A(T), which gives the vibration entropy, and the parameter AH, which gives the energy of solution of a solute atom, to be estimated from the measured variation of solubility with temperature. The solutions treated are dilute enough to enable solute-solute interactions to be neglected so that the partial energy and excess entropy of solution E, and GS are not functions of composition and the configurational entropy is that of a random solution. Large positive values have been found for sxSu this quantity has not been given sufficient consideration in recent work on interstitial solutions and it is felt that the partial thermodynamic quantities of very dilute solutions should be understood before the thermodynamics of concentrated solutions can be fully appreciated. EXPERIMENTAL DATA 1) The Silver-Oxygen System. The measurements of Steacie and Johnson,= using silver foils, indicate that there is a pronounced minimum in the solubility vs temperature curve for O-Ag solutions. Eichenauer and Miiller6 have recently redetermined the solubility of oxygen in silver using a method developed in the investigation of metal-hydrogen systems.7 The solubility determinations were carried out on compact specimens of differing shapes and sizes and the results indicate a much lower solubility than was obtained by Steacie and Johnson with no minimum at 400°C. Subsidiary experiments showed that the erroneous results of Steacie and

Jan 1, 1964

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identi-fied with our modern "Age of Steel" is a relatively brief interval com-pared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the fore-runner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By W. F. Brace, James D. Byerlee

Although prediction of failure of rocks may be ultimately possible without knowing in detail how failure occurs, understanding of this process is certainly of fundamental interest in rock mechanics. Of the various failure mechanisms, probably brittle fracture is of greatest interest. Recent reviews have brought this subject nearly up to date (Hock,1 Price,2 and Jaeger 3) and here, we summarize certain recent developments. As our understanding of brittle fracture is derived almost solely from laboratory studies this will amount to a review of certain laboratory experiments. New studies in four areas are pertinent; these concern 1) the volume changes which accompany brittle fracture, 2) the propagation of cracks in compression, 3) certain frictional characteristics of rocks and minerals at high pressure, and 4) the law of effective stress for crystalline rocks. Our objective here is less to present an entirely consistent, complete picture of how a rock fractures than it is to emphasize gaps in our understanding and, thus, suggest areas that need further study. Progress is still painfully slow in this field and perhaps this approach will stimulate new work. OBSERVATIONS Although the behavior of large rock masses is most often the concern in rock mechanics, the number of large-scale experimental tests is still vanishingly small. Our experimental observations arc, by and large, still made on small, relatively flaw-free, rock samples. Here also we report the behavior of small samples.

Jan 1, 1967

Jan 1, 1961