Search Documents

By R. H. Wightman

THE following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. GEOLOGY The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50º. The bed is approximately 1700 ft. long, 270 ft. thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. MINING METHODS The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. With a hard, tough rock like our limestone, it was found that some alterations in the development and control of draw in caving were necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development I. The fringes of the 800-ft. manway level are driven to confirm the diamond drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1944

By Robert Anderson Cook

AS the margin of profit in the manufacture of iron continues to decrease, attention is called more and more to economies in every department. Beginning at the bottom, in the preparation of the ore at the mine, me notice a general tendency is towards the shipment of richer ores, securing to the mine-owner a better price per ton, which the purchaser is glad to pay by reason of the saving in freight of iron, and in the cost of reduction, which depends so largely upon the amount of fuel and flux, and the productive capacity of the plant. In other words, the difference in value between rich and poor ores is much greater than their relative percentages of iron indicates; because the barren material in a lean ore is not merely worthless, it is a positive source of expense, requiring transportation, handling, fluxing, smelting, and its due share of general expenses; in return for which it yields nothing and decreases the available capacity of a given plant and capital for profitable work. The enriching of the ore is done in most places by hand-picking, and in a few by wet concentration; but the managers of several magnetite mines in Sweden have been practically successful in doing it by machinery. The only magnetic separating machine which has actually taken the place of hand-picking was designed and patented by Mr. Jonas Wenström of Örebrö, Sweden. In this machine, which is illustrated in Figs. 1 and 2, Mr. Wenström has taken advantage of the property of soft iron to become magnetized by induction. The machine consists of a barrel made up of soft iron bars and some non-conducting material (usually wood), which is rotated around a stationary shaft by means of a cog-wheel. Inside of this barrel, on the shaft, is placed eccentrically a cylindrical electro-magnet, provided with a number of manges (N, S, Fig. I), between which wire is wound in such a manner that the flanges are of negative and positive polarity, being energized by a current passing through the wire coils from a small dynamo. As will be seen in Fig. 1, the flanges, N, S, are circular, and follow the internal contour of the barrel on the front side, while on the opposite side they are cut down to the line B, B' in Fig. 2. Hence the bars of the revolving barrel on the front side of the machine are mag-

Jan 1, 1889

By L. C. Graton

Although marked by numerous well-known attributes of its own, gold does not possess a kind and range of physical, chemical and geological characteristics wholly different and apart from those of other metals. Instead, it is merely one of the family of metals, with its individual and distinctive traits subordinate to the underlying family relationships and resemblances. The geologist concerned with pure science will pursue, therefore, the same general course and will examine the same broad kinds of facts and interrelations when studying the occurrence of gold as when studying that of copper or cadmium, or any other metal. But when we come to consider the use and economics of the metals, we discover that gold differs strikingly from all the others. Gold, in short, is unique, not by virtue of its inherent characteristics, but because of a peculiar and concerted psychological regard in which it is held. It will be evident, therefore, that the geologist who would deal with gold supply must give far greater weight to economic considerations than is required in his contacts with any other metal. If the geologist be called the scientist of occurrence, and the economist the scientist of use, the economic geologist stands as the necessary link between them. Perhaps it is in part because the economic geologist has made himself more familiar with the science of occurrence than with the science of use and has thus in some degree failed to bridge effectively the gap between the two fields, especially with regard to gold, that the usen1 of gold now appear to be in a state of general concern and even of alarm for the security and adequacy of future supplies. In the case of no other mineral commodity do the users, as a rule, trouble themselves greatly about the adequacy of supply except in so far as that may affect the price which they shall have to pay for the commodity. Oversupply, with resulting low price, they regard as a gift of good fortune. As to long-term undersupply, they are generally content to go ahead on faith, leaving the producer to discover as best he may the means for meeting their requirements or the inventor to find a substitute. But history has shown that for gold a different situation exists. While

Jan 1, 1931

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By J. Hunter

DuXing 1942, Louisiana attained the rank of fourth among the great oil-producing states of this country. Its present prominent position is the result of an orderly and systematic program of exploitation with emphasis on conservation. Even before the functioning of M-68, the Federal spacing order, development and production in Louisiana were regulated by various acts of legislation, the most recent of which and by far the most effective is Act 157 of 1940. Under the authority of this act, it has been possible for the Department of Conservation to hold many public hearings and thereby to secure data and evidence regarding the feasibility of issuing rules and regulations for development of various oil and gas fields in the state. As a result of information compiled at such public hearings, many orders have been issued by the Commissioner of Conservation that have in most cases provided reasonable solutions to the problems that arise in the exploitation and development of fields in this state. Probably one of the most effective powers granted the Commissioner of Conservation in the state of Louisiana has been the authority to provide for fieldwide unitiza-tion and pooling of condensate fields. This has led to the erection of huge cycling plants in Louisiana, which permit the most efficient recovery of the liquid content of the reservoirs, and further conserve most of the gas reserve that undoubtedly will be of considerable future value. Many months have passed since various orders of the Department of Conservation were put into effect, and all are accomplishing their purpose; namely, the elimination of waste. Although the effectiveness of these orders provides considerable satisfaction to the members of the Department of Conservation, it is also a tribute to the members of the oil and gas industry in Louisiana, who, in addition to providing carefully prepared technical data, have also given unstinting cooperation and have thereby enabled the Department to cope intelligently with the many problems. Production On Dec. 31, 1942, oil and/or gas was being produced in 50 parishes, or 78 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 12 produced oil, and 5 produced solely gas. This is indeed an enviable record for any state. However, it is reasonable to assume that eventually all parishes in the state of Louisiana will be productive. From a geological viewpoint, there is no apparent reason to assume otherwise—a point that a11 operators seeking oil and gas production in this state may well bear in mind. Twenty new fields were found during 1942—a rate of discovery that does not compare favorably with the 30 new fields found during 1941. The record of discoveries in Louisiana during 1942 is further disappointing when it is realized that 8 of the 20 new fields discovered were gas fields. During this period of war emergency, there are, of course, many

Jan 1, 1943

By J. Hunter

DuXing 1942, Louisiana attained the rank of fourth among the great oil-producing states of this country. Its present prominent position is the result of an orderly and systematic program of exploitation with emphasis on conservation. Even before the functioning of M-68, the Federal spacing order, development and production in Louisiana were regulated by various acts of legislation, the most recent of which and by far the most effective is Act 157 of 1940. Under the authority of this act, it has been possible for the Department of Conservation to hold many public hearings and thereby to secure data and evidence regarding the feasibility of issuing rules and regulations for development of various oil and gas fields in the state. As a result of information compiled at such public hearings, many orders have been issued by the Commissioner of Conservation that have in most cases provided reasonable solutions to the problems that arise in the exploitation and development of fields in this state. Probably one of the most effective powers granted the Commissioner of Conservation in the state of Louisiana has been the authority to provide for fieldwide unitiza-tion and pooling of condensate fields. This has led to the erection of huge cycling plants in Louisiana, which permit the most efficient recovery of the liquid content of the reservoirs, and further conserve most of the gas reserve that undoubtedly will be of considerable future value. Many months have passed since various orders of the Department of Conservation were put into effect, and all are accomplishing their purpose; namely, the elimination of waste. Although the effectiveness of these orders provides considerable satisfaction to the members of the Department of Conservation, it is also a tribute to the members of the oil and gas industry in Louisiana, who, in addition to providing carefully prepared technical data, have also given unstinting cooperation and have thereby enabled the Department to cope intelligently with the many problems. Production On Dec. 31, 1942, oil and/or gas was being produced in 50 parishes, or 78 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 12 produced oil, and 5 produced solely gas. This is indeed an enviable record for any state. However, it is reasonable to assume that eventually all parishes in the state of Louisiana will be productive. From a geological viewpoint, there is no apparent reason to assume otherwise—a point that a11 operators seeking oil and gas production in this state may well bear in mind. Twenty new fields were found during 1942—a rate of discovery that does not compare favorably with the 30 new fields found during 1941. The record of discoveries in Louisiana during 1942 is further disappointing when it is realized that 8 of the 20 new fields discovered were gas fields. During this period of war emergency, there are, of course, many

Jan 1, 1943

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969

By S. S. Raymond, C. R. Hayward

In reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment be carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired temperature throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treatment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-know tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels which, after tempering for periods varying from 15 min. to 2 hr., show no very great bifferences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 1, 1917

Jan 1, 1970

By R. H. Wightman

The following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. Geology The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50°. The bed is approximately 1700 ft. long, 270 ft, thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. Mining Methods The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. with a hard, tough rock like our limestone, it was found that some alterations in the development and control of dm, i, caving were. necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development 1. The fringes of the 800-ft. manway level are driven to confirm the diamond-drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1946

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying tip pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By C. H. Li, R. D. Carnahan, R. J. Stokes, T. L. Johnston

When silver chloride deforms by pencil glide at temperatures of 26ºand 72°C, grain size has no effect upon the proportional limit and the material necks down to a knife edge under tension. At -196ºC, deformation takes place on fewer slip systems to produce straight slip traces, the flow stress becomes sensitive to grain size and fracture occurs by cleavage from an intergranular source without any reduction in area. THERE are significant differences between the appearance of the slip bands formed in silver chloride and in the alkali halides at room temperature. The bands in sodium chloride, e.g., are fine and geometrically straight, whereas in silver chloride they are coarse and wavy.&apos; Such differences in the slip behavior prompted us to inquire what the effects of grain boundaries might be on the mechanical properties of these solids. As an introduction to a general study of ionic poly-crystal behavior, we have investigated the effect of grain size on the stress-strain relationships in silver chloride at different temperatures. We have chosen silver chloride chiefly because polycrystals can be easily prepared free from cracks and macroscopic voids by conventional techniques. Moreover, as we shall see, the slip behavior can be readily modified by changing the temperature. It will be shown that the effect of grain size on the yield stress of silver chloride is strikingly dependent upon the temperature of deformation and that this temperature effect comes about through a change in the number of slip systems which operate at the onset of plastic flow. EXPERIMENTAL PROCEDURES Polycrystalline tensile specimens were made by recrystallizing cold-rolled AgCl sheet. Thirty-gram quantities of AR grade silver chloride powder were melted in a low heat capacity furnace, cast into cylindrical forms 3/4 in. in dim and approximately 1 in. in length and then extruded with a 16:l reduction ratio into rods 3/16 in. in dim. Extrusion temperatures were varied from room temperature to 350°C. In order to impart various degrees of cold&apos;work to the extruded rod. All extrusions were then cross rolled to sheet 0.040 in. in thickness at room temperature and machined to form tensile specimens having a gage length of 0.750 in. with a width of either 0.250 or 0.145 in.* Annealing was carried out in an air oven at 200°C for periods up to 20 hr. specimens having average grain diameters ranging from 0.024 to 0.40 mm were prepared by varying the extrusion temperature and annealing time in the conventional manner. To obtain specimens with grain sizes larger than 0.40mm, lightly deformed thin prisims of silver chloride single crystals (supplied by Harshaw Chemical Co.) were recrystallized. Grain size determinations were made by an intercept method and revealed that the grains were equi-axed. Laue back-reflection X-ray patterns showed little tendency to form a preferred orientation texture. Specimens which were to be used for the slip band studies were polished by immersion in fresh boiling concentrated NH,OH for 60 sec. They were then etch polished for 10 sec on each side by hand lapping on a stationary velveteen lap wetted with a dilute Hypo solution (5 g of Kodak Acid Fixer in 100 cc H20). Finally the specimens were rinsed in warm water and alcohol, blown dry and carefully mounted in the tensile machine for testing. Tensile tests were performed at three temperatures, namely, 26º, -72º, and -196°C. A screw-driven hard tensile machine was used at a constant strain rate of 0.006 in. per in. per min. Loads were determined with a light- proof ring fitted with A-18 strain gages and extensions were measured with a 0.0001 in. dial gage. Constant level baths of alcohol with dry ice and liquid nitrogen were used to maintain the two lower test temperatures. EXPERIMENTAL RESULTS Reproducibility—In view of the light sensitivity and reactive nature of silver chloride, it was necessary to determine whether reproducibility depended upon either exposure to light or to the condition of the surface. However, during the course of the work it became clear that variation of laboratory lighting

Jan 1, 1962

By Arthur Braid

The war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find—in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferromanganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within the last few years, and particularly since the war began, the .great value of mangancse in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 1, 1919

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940&apos;s it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By J. S. Hardison

In the fall of 1912, the appearance of water in the oil of the Nevada Petroleum Co., Coalinga, Cal., made necessary the installation of a dehydrating plant to reduce the water below the 3 per cent. limit prescribed by the agency. Unlike the mining industry, technical literature of the oil industry is limited and extremely unsatisfactory. Until the recent efforts of the Petroleum and Gas Committee of the American Institute of Mining Engineers, no concerted movement has been instituted to secure publication of papers dealing with the problems of the oil business, and because of the additional fact that dehydrating of oil has not been practiced in California to any extent up to comparatively recent time, it was found necessary to experiment in order to determine the most satisfactory plan for this purpose. It is easy to write regarding successful enterprises, but, while not SO pleasant, it is equally desirable to write of failures so that others may be saved the loss incident to such investments. The water in this oil occurs both free and as an emulsion. Free water easily settles out, but the emulsion requires treatment. So far as can be determined, the emulsion consists of globules of water surrounded and enveloped by a film of oil. Starting with this hypothesis the theory has been evolved that in order to break up this emulsion the water must be heated at least to boiling point, when an explosion takes place destroying the globule. Unfortunately, this condition was not recognized in the installation of the first plant, which was planned on the following lines: A heater was arranged so that all the oil from the wells could be heated before reaching the shipping tanks, these being already fitted with coils for steam heating. Tanks were filled with about 4 ft. of water, live steam was turned into the coils and the water brought nearly to the boiling point, when the heated oil was run in. This for a time was partly successful, but the length of time necessary to apply this heat was too great for practical operating.

Jan 1, 1915

By Ralph Arnold

IN OPENING the symposium under the auspices of the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers, I wish to call to your attention the following, among other subjects, which it is hoped may receive proper attention: 1. The recording of as accurate an appraisal of the oil possibilities of the various countries as is possible, with information as to the immediate availability of their supply. 2. The development of further support for the move-ment to bring about active cooperation among Ameri-can oil companies in their foreign exploration and development work. 3. The furtherance of the efforts of the industry in securing governmental assistance in foreign oil develop-ment: (a) along the lines of a modification of our domestic oil policy, so that we can go to foreign coun-tries and consistently ask fair treatment as to royalties and bonuses; (b) by a closer cooperation between the State and Commerce Departments and the oil industry. 4. The calling of attention to the unjustifiably drastic action of the price-fixing group of the oil industry during the last year or so, with the hope that it will use gentler methods in the future. None of these subjects are new, and some of them have been discussed before various organizations for years. Our justification for again bringing them forward is the hope that by everlastingly harping on them the industry, the Government, and the people who shape the destinies of this country may some time, some how, realize their importance and take effective constructive action.

Jan 6, 1922

By R. W. Raymond

THE Brüclrner roasting-cylinder is well known as an apparatus which has done good work in the desulphnrization, particularly of refractory silver ores, in the western districts of this country. A paper by Mr. J. M. Locke, of Cincinnati, describing the cylinders, as constructed by Messrs. Lane & Bodley, in that city, may be found at p. 295, vol. ii., of the Transactions of the Institute; and a paper by Mr. N. H. Cone, vol. iv., p. 226, gives an account of their operation in Colorado. The purpose of the present paper is to present an .improved construction, designed by Mr. Brückner. This is clearly shown in the accompanying plate, which scarcely needs explanation. It will be seen at once that this construction involves two cylinders, instead of one. Mr. Brückner thinks that three cylinders might be better yet, as securing an exact mechanical reproduction of the work of the well-known three-hearth Fortschaufelungsofen, the most perfect of the reverberatories in which delicate roasting is performed with hand-labor. THE APPARATUS. Erection of the Cylinders.—Although the cylinders may he put lip at any locality, or added to existing works, it is preferable, if possible, to choose the site on a hill sloping naturally, say about 30&apos; or 33. Two excavations are made, one 8 to 12 feet higher up than the other; and each is protected by a wall with a batter of about 1 inch to the foot, to prevent slides of stone and earth. Each cylinder being 20 feet long and 7 feet in diameter, the total excavation should be 60 to 70 feet along the hill, and 15 to 25 feet wide. On each level a building is erected 35 feet long by 20 feet wide and 12 feet high, with the roof containing a ventilator against the hill. When both buildings are on the same level, there should preferably be a solid frame-work of very heavy timber, to carry the four rollers which bear the upper cylinder. The four rollers carrying the lower cylinder should preferably rest on two very heavy pieces of timber, strongly braced together and laid to their top in a foundation made of stone or brick and cement. Foundations are necessary only under each two opposite rollers, but they must be made carefully,

Jan 1, 1886

By J. J. Kanter

The choice of a nonferrous metal or alloy for a given Application is frequently predicated upon a consideration of properties other than merely the capacity to withstand stress. When ability to withstand stress is the dominant engineering requisite of the material to be used, economic considerations seldom lead to the choice of nonferrous metals and alloys. In most instances where a nonferrous metal is used it is because of some special quality of either corrosion resistance, electrical properties, thermal properties, antifriction, or fabrication advantage that commends its application. The mechanical properties, as a rule, present an incidental engineering consideration entirely secondary to the special quality deciding its use. Indeed, great ingenuity has often been exhibited by engineers and metallurgists in overcoming the mechanical shortcomings of a nonferrous base material. in order to take advantage of some outstanding property. . With this thought in mind, we might better appreciate some of the problems in stress design. encountered with nonferrous metals and alloys pertinent to a symposium on their creep characteristics. Our considerations must necessarily be far from complete because of the broad range of materials in the nonferrous category for which creep properties assume a technical interest. Creep deformation of these metals can be subject for study at temperatures ranging from ambient to incandescent, depending upon which one is under consideration. Whereas the steel metallurgist thinks of creep as an essentially high-temperature engineering consideration, the same is not necessarily true in the field at hand. The diversity of the creep problems in the nonferrous field is perhaps accountable to some extent for its virginity as a symposium subject. Each research has necessarily been sponsored by some organization or group interested either in promoting the use of a certain nonferrous base or in obtaining data toward the solution of a mechanical difficulty encountered in applying a material indispensable for its special attributes. Perhaps as many techniques of creep testing have been used as there are base metals implied under "nonferrous." Some of the creep problems that have occasioned researches are associated with steam-pressure vessels such as tubes, drums, castings, and forgings of copper-base and nickel-base alloys, cable sheathings of lead and lead-base alloys, electrical transmission lines of copper and aluminum, engine parts die-cast from alloys based on zinc, aluminum, copper— soldered and brazed joints-—as well as numerous duties at extremely high temperatures met with alloys based on cobalt, nickel, tungsten, molybdenum, platinum, and other precious or semiprecious metals. Postwar technology will have the benefit of much creep research on nonferrous metals, which for reasons of security cannot be discussed on this occasion. Suitability OF Metals As already intimated, the bulk of the constructional metal that ordinarily is

Jan 1, 1945

By W. D. Forgeng, R. L. Folkman, D. C. Hilty

The solubility of oxygen in molten Fe-Cr alloys has been determined at 1550° , 1600°, and 1650°C for alloys containing up to alloyshasbeenabout 50 pct Cr and found to decrease as chromium increases to 6 pet and then to increase gradually. Phase relations in the Fe-Cr-0 system at steelmaking temperatures have been evaluated and two previously unreported oxides have been identified. OPERATIONS in the melting and refining of chromium steels are dependent to a major degree on the reactions of chromium and iron with oxygen and are primarily directed toward controlling and modifying these reactions to secure maximum advantage in the utilization of chromium. Although fairly effective practices have been developed empirically, understanding of the specific reactions is limited. Moreover, the ability of molten steel to dissolve oxygen that subsequently precipitates as oxide inclusions during solidification is well known, so that clarification of the effect of chromium on the nature and mechanism of formation of these inclusions is desirable. Study of the problem indicated that increased knowledge of the fundamental Fe-Cr-0 system is essential to further technical and economic improvement. Consequently, an investigation of the influence of chromium on the solubility of oxygen in molten iron and of phases and phase relations in the Fe-Cr-0 system was undertaken at the Metals Research Laboratories of the Electro Metallurgical Co. as part of a general program on the effective utilization of chromium in chromium steel production. Experimental Procedure All of the experimental runs made during this investigation were carried out in the rotating crucible induction furnace which has been described in detail in a previous publication.&apos; In review, the principle underlying this furnace is that rotational forces in the crucible cause the molten metal to assume a concave shape in such a manner that the slag is contained in the molten metal cup, thereby minimizing slag/crucible contact and subsequent reaction. Practically all of the heats were melted in commercial-quality magnesia crucibles of the type usually furnished for laboratory induction furnaces. All of the runs were made under an argon atmosphere after the furnace chamber had been degassed. Bath temperatures were controlled by Pt—Pt-10 pct Rh thermocouples. The basic furnace charge consisted of a premelted 12 to 15 lb electrolytic iron slug which had been cast to a shape convenient for fitting into the rotating furnace crucible. A typical analysis of the electrolytic iron slugs is given in Table I. For certain runs, it was desirable to melt down charges containing high initial chromium contents. In these cases the chromium was added to the electrolytic iron during the premelting operations. Chromium was added to the rotating furnace bath in the form of electrolytic chromium of the analysis given in Table 11. In all of the constant temperature runs, the standard procedure was to melt down the electrolytic iron or alloy slug under vacuum, admit argon to slightly greater than atmospheric pressure, and adjust rotational speed to develop a well formed "cup" on the bath surface. The melt was then saturated with oxygen by an addition of ferric oxide and the temperature of the bath adjusted to within +5°C of the desired level. At this point the heat was permitted to come to equilibrium prior to sampling or further addition. This time interval was varied from 15 min to 2 hr but generally was about 20 min. After sampling, the desired chromium addition was made and the bath again equilibrated prior to subsequent sampling. This cycle of addition and sampling continued for the duration of the run which lasted from 4 to 8 hr. At the end of this period, power was shut off and the bath allowed to solidify in the furnace. Quenched metal samples were taken from the equilibrated melts by means of the "Taylor sampler" which has been described by Taylor and Chipman.&apos; Before being submitted to chemical analysis, all samples were carefully examined for surface slag occlusions and cold shuts. Later in the study, each sample was radiographed and examined metal-lographically in cross-section to determine the presence of internal defects. On the basis of these examinations, sound and apparently clean specimens were selected from the Taylor samples for chemical analysis.

Jan 1, 1956

By F. B. Foley

IT is with an unusual degree of personal satisfaction that I find myself in a position to pay tribute to the memory of Henry Marion Howe. One could not have spent any length of time in the presence of Dr. Howe without profiting intellectually. I do not hesitate to say that my years of association with him were the most stimulating of all my years of metallurgical study. He always impressed one with his own eager search for knowledge. Never dependent on the written word alone he sought information from anyone whose opinion he valued. His ability to piece together bits of apparently conflicting data from various sources so as to build up a logical hypothesis was unique. A small slight man with the intellect of genius he would have gone to the top in any endeavor he undertook and it was fortunate for metallurgy that its study attracted him as it did. Howe was a modest man. I like to recall an incident which left a lasting impression with me. The lab- oratory in his home, "Green Peace," was in the basement and access was by way of stairs leading down from his secretary&apos;s room. In using these stairs my attention was attracted many times to an ordinary cardboard shoe box which reposed on the shelf above the landing. It was crudely labeled on its side in black ink "Vanity Box." My curiosity was aroused to the point that I finally asked his secretary what it was. With some amusement she took the box from its shelf on the stairway, opened it and showed me its contents—numerous letters, from the foremost men of science of every civilized country throughout the world, commending his "Metallography of Steel and Cast Iron." I recall that in reply to one who thought there was not enough of Howe&apos;s own researches in his book he wrote, "Primarily I am a writer, secondarily an investigator." Howe wrote to make his readers think. No one ever strove harder than he to be right but above all, whether his viewpoint proved ultimately to be right or wrong, he was always content if by his stand, he provoked a reader to take the next step along the path to greater knowledge. I doubt that he was ever afraid to be wrong for he was always secure in the thought that his effort was guided by a sincere search for the truth. One continually searching for truth is entitled to occasional excursions up the wrong alley. A glance backward to the metallurgical confusion of some thirty to forty years ago, or need one go back so far, provides convincing proof of what a host of companions one may have in a common acceptance of ideas which the future will prove to be wholly untenable. Well over a hundred years have passed since investigators have interested themselves in the effect of increasing the temperature of iron and steel on their mechanical properties. We are told by Charles Walrandl in "Industrial Annals" for June 11, 1822, that bend tests, conducted in a Russian steel works of Prince Demidoff, on steel bars "highly heated" and bent during cooling became brittle when bent at an iris blue color. He concluded, "That when steel is heated to a temperature between 473°F and 662°F the mettle was more brittle between these limits than at a much lower or at a much higher temperature." It was a curious bit of information recognized as true to this day and still not explained satisfactorily. In 1878 Charles Houston in Annales de Mines associated this brittleness with an increase in tensile strength at 572°F. When this relatively low temperature is exceeded it is recognized that steel becomes weaker as temperature is increased up to the melting point, where no strength of practical importance remains. It is easy to believe, in fact it goes without saying, that this weakening as the temperature of a metal is increased is the result of the motion of the atoms making up the metal, a motion which itself is evidence of the temperature increase. However, if we are considering iron or steel we find that this decrease in strength is not a steady one, for, besides the increase in strength just referred to, one comes to a temperature, the critical temperature, where results of tests indicate the metal to be extremely weak and then as temperature increases to become sensibly stronger again. This apparent anomaly was made the subject of the first Howe Memorial Lecture, delivered by Albert Sauveur in 1924. It may be of interest to review these findings of Sauveur. He used two methods of investigation. One involved the twisting of bars. The bars were heated in an

Jan 1, 1951