Search Documents

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By G. A. Savanick

Borehole (slurry) mining, where a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a US Bureau of Mines program to increase the domestic availability of critical minerals. About 1.5 kt (1700 st) of phosphate ore were mined at 23.6 t/h (26 stph) from a depth of 76 m (250 ft). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1986

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By P. L. Lavery

A numerical method to derive approximate solutions for stress intensity factors for rectilinearly anisotropic bodies without resolving to complex variable approach is presented. The method is based on the assumption that the crack opening profile can be simulated by a simple curve such as an elliptic function and a relationship is found for the stress intensity factor in terms of near tip displacements. An example solution is derived for a transversely isotropic body and the results are verified with Westergaard's stress function approach. The proposed model has a great potential for the applications to fracture mechanics of anisotropic rock materials.

Jan 1, 1984

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By Orson Shepard

THE term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 19341. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner:. . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1936

By Gilbert Soler

Page Introduction. By Gilbert Soler.........................657 Deoxidation of Basic Open-hearth Steel. By T. S. Washburn.............658 Slag-metal-oxygen Relationships in the Basic Open-hearth and Electric Processes. By J. S. Marsh. (With discussion)...........................672 The Total Oxygen Content of Plain Carbon Open-hearth Steel during Deoxidation and Teeming. By Michael Tenenbaum and C. C. Brown. (With discussion)......685 The Occurrence of Oxygen in Liquid Open-hearth Steel—Sampling Methods. By T. E. Brower and B. b. Larsen..........................712 Effect of Deoxidation on the Strain-sensitivity of Low-carbon Steels. By H. K. Work and G. H. Enzian. (With discussion)........................723 The Relation among Aluminum, Sulphur, and Grain Size. By C. E. Sims.......734 Some of the papers and discussions that appear on the following pages were presented at the meeting of the Iron and Steel Division in Cleveland, Ohio, on Wednesday, October 18, 1944. with L. F. Reinartz and H. K. Work as Chairmen; the remainder were scheduled for the New York Meeting of the Institute in February 1945, which was canceled.

Jan 1, 1945

By W. A. Hockings, M. E. Volin, A. L. Mular

Batch grinding tests at short times were made in a laboratory rod mill with 10 x 14 mesh quartzite in corn syrup-water mixtures of varying viscosity. The weight fraction broken and size modulus were found to be independent of viscosity up to 20 cp, but at higher viscosities breakage of the feed decreased while the size modulus increased. The mechanisms of the effect of viscosity are discussed on the basis of particle dynamics. The effect of viscosity of the suspending medium on grinding has not been accorded much attention, although both wet and dry grinding are used in bene-ficiation processes and the viscosities of water and air differ greatly. schweyerl investigated the rates of grinding of quartzite in a pebble mill with air, water and glycerol as the suspending media and found the rate in terms of new surface developed per thousand revolutions of the mill to be constant and dependent on viscosity up to 20,000 rev, but to decrease and become independent of viscosity for longer grinding times. Based on considerations of the drag forces exerted on suspended particles and on the grinding media under turbulent and laminar flow conditions, viscosity can be expected to inhibit the rate of grinding in a given system as it changes the flow conditions from turbulent to laminar. The objective of this study was to determine the effect of viscosity of the suspending fluid in the batch grinding of a homogeneous feed of uniform size for short residence times, a region of more practical interest than the long times investigated by Schweyer. In actual grinding operations, the viscosity of the fluid does not change, but the consistency (apparent viscosity) of the pulp increases with additions of fines. In this study the consistency of the pulp was not measured because it was thought that the grinding times were too short to alter the apparent viscosity appreciably.* *Minus 200 mesh quartz at 65% solids has an apparent viscosity of about 25 cp as measured by a simple consistometer. Personal communication from D. F. Kelsall to A. L. Mular. For the purposes of this study, the effect of viscosity on grinding can be shown sufficiently well on the basis of the cumulative weight fraction finer than the feed size at any time, and the size modulus, ku, of the finer than feed sizes. The parameter, ku, is obtained from a form of the Gaudin-Schuhmann equation. METHOD AND MATERIAL The grinding tests were accomplished in a laboratory rod mill 10-1/2 in. long and 8 in. bore with a 20-lb rod charge consisting of two 1-in., eight 3/4-in., eight 1/2-in., and eight 1/4-in. diam rods. The mill speed was 43.2 rpm. Charges of 400 g 10 x 14 mesh Wisconsin quartzite** were ground for times of 60, **Courtesy of Minnesota Mining and Mfg. Co. 120, 180 and 240 sec in 500 cc of fluid made up of corn syrup and water in measured proportions. The temperature of the pulp was measured immediately upon completion of grinding, and the size distribution of the quartzite was determined by a wash-wet-dry screening technique. Corn syrup was chosen because of its high viscosity and ideal viscous behavior, and also because its density is not greatly different from that of water. The viscosity of each fluid mixture was measured with an Ostwald viscometer at 25 C. and a correction was made for the temperature of the pulp according to tabulated values for sucrose solutions. The density differences were so small that they probably did not significantly affect breakage. RESULTS AND DISCUSSION The conditions of the grinding tests, computed viscosities, weight fractions finer than the feed size and values of a and ku are listed in Table I. The values of a and ku were taken from the linear portions of the log-log plots of cumulative weight fraction finer vs size for the various grinding times. The plots for tests in fluids of average viscosity 8.6 cp are shown in Fig. 1. In general all of the sets of curves were linear throughout most of the size

Jan 1, 1965

By David, Levinger

THESE observations of the metal-working industries of Europe are based on a three months' tour of eight countries of Europe, in which 75 industrial establishments were visited in England, France, Germany, Belgium, Holland, Italy, Austria and Switzerland during the summer of 1927. Since the Western Electric Co. is a large consumer of copper and brass, these industries were of particular interest and differences in practices were of keen interest to us.

Jan 1, 1928

By R. S. Craig, W. E. Wallace, G. S. Kamath

The destruction of long-range order in Mg-Cd, has previously been thought to occur as a second order process. In the present work a variety of X-ray diffraction techniques are employed to show that in this case and in Mg-Cd alloys containing frorn 20 to 33 1/3 at. pct Mg the process more nearly resembles an ordinary first order phase transformation. It is found that the ordered alloy, which occurs as a single phase at lgw temperatures, transforms with increasing temperature into a Cd-enriched disordered (P) phase and an Mg-enriched ordered (a) phase. The interval over which these two phases coexist under apparently equilibrium conditiovs extends from 25" to 87°C content. At 33 1/3 at. pct Mg the two-phase region has disappeared. Measurement of the long range order parameter, s, for the ordered phase in MgCd, (from superlattice line intensities) shows that it disorders only very slightly before it is transformed into the p form. Kinetic experiments reveal that when the a phase is formed frorn the p phase by suitably quenching so as to suppress phase segregation, the transformation is essentially complete and the a phase has acquired its equilibrium value of S in less than 1 min. In an earlier investigation carried out in this Laboratory1 the rate of disordering of the MgCd3 superlattice was determined over an extensive range of temperature. The process was found to be first order and the rate constant, k, was established. At the lowest temperatures studied k was found to increase exponentially with temperature. At higher temperatures, however, it passed through a maximum and for the 100 deg interval below the point at which the superlattice was destroyed k was observed to decrease with increasing temperature. The various theoretical treatments1-3 of order-disorder phenomena lead to a negative temperature coefficient for k near the superlattice critical temperature but this region for MgCdB seemed unusually wide. Detailed analysis of the point indicated' that either the long-range order parameter, S, for MgCda varied with temperature in an anomalous way or the disordering in this instance is more complex than in the cases which have been treated theoretically. The original objective in the present work was simply to determine S vs temperature for MgCda to ascertain whether the disordering was in conformity with theoretical expectations.2° In an early stage of the work it was noted, however, that under equilibrium conditions ordered (a) and disordered (0) phases coexist in MgCd, over a considerable range of temperature. Since on thermo- dynamic grounds the coexisting phases must differ in composition, the investigation was enlarged to permit the compositions of the two phases in MgCd3 to be determined and to establish the extent of the two phase regions for alloys containing from 20 to 33 1/3 at. pct Cd.

Jan 1, 1963

By Michael B. Moolman

Both conventional and nonconventional process alternatives for gold recovery from cyanide heap leach solutions are discussed in terms of possible flowsheets. Conventional process alternatives include carbon adsorption and zinc dust precipitation, while nonconventional process alternatives include resin ion exchange, solvent extraction, and direct electrowinning. These strategies for gold recovery are compared on the basis of technological features and on the basis of process economics: Review of the technology status and process economics suggests that improvements for conventional process alternatives are possible and that further development of nonconventional process alternatives is warranted.

Jan 1, 1984

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By F. R. Hewitt

THE methods of mining talc are simple, and in western North Carolina are almost entirely by open cut and quarry. The larger part of the talc of this section lies in various-sized "veins" inclosed in quartzitic walls, the majority of which have by folding been thrown into a perpendicular position, or nearly so, and the exposed edges of which have been covered by debris from erosion of the mountain above. This covering of loose rocks and earth is from 5 to 25 ft. thick, and in most cases has to be removed because it is difficult to support. Sometimes the covering is heavy enough to "catch" and timber successfully, and in this case the talc can be worked out by the usual method of following the "vein," using stulls for holding up the walls until the vein is worked out, and then allowing the cut or drift to fall in. In some cases it proves more convenient to sink shafts and run drifts, following the talc "veins" until exhausted. The talc deposits of this section are badly broken and faulted both laterally and perpendicularly, and in some cases are found many feet below the level of drainage, necessitating pumping at considerable expense. . My own experience in mining talc has been that the chief point is to get a reliable "vein," and that then the mining is not as difficult, or any more so at least, than that of any common ore. If the. "veins" are pure talc it is simple; if the talc is admixed with foreign matter, such as tremolite in excess, or stains of iron or manganese, as is often the case, one had better abandon the deposit.

Jan 8, 1916

By M. R. Geer

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built.

Jan 7, 1953

By W. R. Ingalls

The manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been done chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the re-verberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood, and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Con City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose. Just as zinc may be burned off in a blast furnace, so also may it be done in a reverberatory. Indeed, there is less trouble, in some respects, in a reverberatory, for therewith there is no shaft in which accretions may

Jan 1, 1918

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Technical graduate, aged-31, with experience as surveyor, chemist with a sulphur company, practical miner, and as chief engineer of an iron mining company, desires a position as mining engineer or superintendent. Speaks French and German. No. 165. Member, aged 31, married, graduate Yale and Massachusetts Institute of Technology, six years' experience in coal and iron mining, from engineer to general superintendent, desires position with large coal or iron company. Will go anywhere. References. . No. 167. Member, technical graduate, with experience as machinist, chemist, construction engineer, and manager-of mines in the United States and Mexico, desires position .as mine superintendent or manager. Speaks Spanish. No. 168. Member, technical graduate, aged 26, with experience as engineer, mine foreman, assistant superintendent for a pyrite mining company. Experience includes diamond drilling, shaft sinking, underground work, milling of pyrites, and mine accounting. No. 169.

Jan 12, 1914

By Edward Griffith

The anthracite industry, which produces about 50 million net tons of coal annually, has been talked of as being able to last for another century; but if the water record of the past century continues into the expected century, this expectation of many years production still to come out of the remaining reserves will not be attained. The industry will be a submerged one in fact as well as in name. A recorded forecast of what has since occurred appears on page 34 of the Mine Inspectors' reports of 1897: It should also be noticed that bodies of water had accumulated in parts of abandoned mines before duplicate surveys of the same were required by law; and as a result we have today to contend with bodies of water, the exact location and position of which are not correctly known. Since that date, 47 years ago, the implications of the foregoing comment have grown enormously. This is shown in Fig. I and in the following table showing flooded and partially flooded areas that have come into existence since the early 1930's in the northern anthracite field: Number of Year Flooded Areas 1932...................... 2 1933...................... 3 1934..................... 3 1935...................... 5 1936...................... 7 1937...................... 9 1938.................... 11 1939...................... 11 1940...................... 11 1941...................... 14 1942...................... 14 1944...................... 26 Similar conditions exist in other fields in the anthracite region. In the period between 1923 and 1940, abandonment of collieries in the southern field resulted in the flooding of approximately 60 sq. miles (30 per cent) of the field. The ahandonment of collieries in this field has imposed additional expense for pumping on the collieries still operating. This condition will be aggravated by the extension of developments and cause suspension of operations if economic conditions do not justify the assumption of additional pumping costs. During the years, the region's rainfall has not altered, but the quantity going inside the mines through breakages in the surface, brought about by extraction of the coal, has increased materially, as indicated by the ratio of tons of water pumped to tons of coal produced underground for one of the large companies in the northern anthracite field: Year Ratio 1920................. 8.4:1 1925.................. 10.6:I I930.................. II.4:I 1935................. 26.2:1 1940.................. 32.7: I 1942.................. 30.3:I The data in Table I shows the total amount of water pumped and its ratio to underground production for one of the large companies in the southern anthracite field, and shows a rapidly growing serious situation. Rainfall quickly affects the workings in all the fields. In mine inspection district 7 of the southern field the rainfall in 1935 was 92,083,000,000 gal. The total water pumped was 36,274,000,000 gal. (39.4 per cent of the rainfall). The operating mines

Jan 1, 1947

By Edward Griffith

The anthracite industry, which produces about 50 million net tons of coal annually, has been talked of as being able to last for another century; but if the water record of the past century continues into the expected century, this expectation of many years production still to come out of the remaining reserves will not be attained. The industry will be a submerged one in fact as well as in name. A recorded forecast of what has since occurred appears on page 34 of the Mine Inspectors' reports of 1897: It should also be noticed that bodies of water had accumulated in parts of abandoned mines before duplicate surveys of the same were required by law; and as a result we have today to contend with bodies of water, the exact location and position of which are not correctly known. Since that date, 47 years ago, the implications of the foregoing comment have grown enormously. This is shown in Fig. I and in the following table showing flooded and partially flooded areas that have come into existence since the early 1930's in the northern anthracite field: Number of Year Flooded Areas 1932...................... 2 1933...................... 3 1934..................... 3 1935...................... 5 1936...................... 7 1937...................... 9 1938.................... 11 1939...................... 11 1940...................... 11 1941...................... 14 1942...................... 14 1944...................... 26 Similar conditions exist in other fields in the anthracite region. In the period between 1923 and 1940, abandonment of collieries in the southern field resulted in the flooding of approximately 60 sq. miles (30 per cent) of the field. The ahandonment of collieries in this field has imposed additional expense for pumping on the collieries still operating. This condition will be aggravated by the extension of developments and cause suspension of operations if economic conditions do not justify the assumption of additional pumping costs. During the years, the region's rainfall has not altered, but the quantity going inside the mines through breakages in the surface, brought about by extraction of the coal, has increased materially, as indicated by the ratio of tons of water pumped to tons of coal produced underground for one of the large companies in the northern anthracite field: Year Ratio 1920................. 8.4:1 1925.................. 10.6:I I930.................. II.4:I 1935................. 26.2:1 1940.................. 32.7: I 1942.................. 30.3:I The data in Table I shows the total amount of water pumped and its ratio to underground production for one of the large companies in the southern anthracite field, and shows a rapidly growing serious situation. Rainfall quickly affects the workings in all the fields. In mine inspection district 7 of the southern field the rainfall in 1935 was 92,083,000,000 gal. The total water pumped was 36,274,000,000 gal. (39.4 per cent of the rainfall). The operating mines

Jan 1, 1947

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, . Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, - William R. Webster. Henry 1%1. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson, The Board of Directors of the Institute has authorized the holding of a meeting under the auspices of the Iron and, Steel Committee in New York City, October 16 and 17, 1913. Gratifying responses have been received to the request of the Committee for contributions, the following papers being already assured: 1. H. M. Howe, Equilibrium Temperature for A, in Carbon Steel. 2. H. M. Howe, The Divorcing of the Eutectoid in Meteorites. 3. H. M. Howe and A. G. Levy, Determination Of the Position of Ae3, in Carbon-Iron Alloys. 4. G. .K Burgess, J. J. Crowe and H. S. Rawdon, Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels. 5. H. Dl. Hove, Discussion of the Existing Data as to the Position of Ae3,. 6. J. H. Hall, Shock Tests of Cast Steel. 7. H. F. Miller, Jr., The Design of Regenerators for Open-Hearth Furnaces. 8. E. Stütz, Paper on the "Scoria Process." 9. Albert Sauveur, Mayari Steel. 10. Felix A. Vogel, Briquetting. 11. J. E. Johnson, Jr., Paper on " Cast Iron."

Jan 6, 1913