Search Documents

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965

By David A. Rice

This note describes a simple, rapid technique for measuring the apparent volume and density of individual bits of porous materials such as iron ore pellets or pieces of coke. The method consists of determining the weight recorded on a balance when a particle is depressed below the surface of mercury, and calculating the apparent volume from the known density of mercury. The apparent density is calculated after weighing the particle in air. The method is particularly well suited for applications where a great number of determinations are to be made. An additional benefit is the minimal handling of the mercury. In any event, the usual recommended safety precautions should be adhered to.

Jan 1, 1982

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10, 1919, to August 10, 1919. BALL, C. LEONARD.. Cons. Engr., Suffern Co., Inc., 135 Broadway, New York, N. Y. BARRY, CHARLES W Box 502, Idaho Springs, Colo. BATTLE, JOEL ALLAN, JR., Min. Engr., U.S. Bureau of Mines, Room 2114, Interior Bldg., Washington., D. C. BEER, GUIDO, Compagnia. Italian, Dir Bronzi Speciali, C. I., B. S. La Direzione, Italy. BITLER, WILLIAM F., Management of Coal Properties, The Provident Life & Trust Co. of Philadelphia, 409 Chestnut St., Philadelphia, Pa. BLOOM, SETH W., Chief Engr,, Northwestern Min. & Exchange Co., 130 E. Sribner Ave., Du Bois, Pa. BOYDELL, W. Guy B., Min. Engr., Tul Mi Chung Mine, Care Seoul Min. Co. Whang Hai Do, Chosen. Korea. BRYAN, RUSSELL R.., Met., Sunnyside Min. & Mill. Co., Eureka, San Juan Co., Colo. CHIAPELLA, STEPHEN EUGENE 323 W. 30th St., Los Angeles, Cal. CONWAY, EDMUND JOHN, Exploration Engr., Granhy Consolidated Min., Smelt & Power Co., Ltd., Anyox, B. C., Canada. DEMOREST, DANA J Prof. of Met., The Ohio State Univ., Columbus, Ohio. EIDEMILLER, H. N., Geol., Benjamin C. Neely, Min. Lands & Leases, Crystal Falls, Mich.

Jan 9, 1919

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

Sponsored by the Utah Section of AIME, the 1960 Annual Rocky Mountain Minerals Conference brought more than 500 members of the mineral industry to the conference rooms of the Newhouse Hotel in Salt Lake City during the period October 5 to October 7. Under the overall supervision of J. M. Ehrhorn, general chairman, and H. E. Wright, assistant general chairman, the Conference offered 14 papers of technical interest in four sessions during the first two days, and it culminated in the Exploration Symposium held on the morning of October 7. The opening session of the Conference, meeting on the morning of October 5, heard R. P. Work, utility engineer of the Mountain Fuel Supply Co., discuss the growth and economic factors related to the use of natural gas in Utah. In his paper entitled Natural Gas Market In Utah, Mr. Work emphasized the very good prospects of natural gas serving almost all parts of that state. He mentioned that recently the El Paso pipeline, built to serve the Pacific Northwest with gas from Texas, has permitted natural gas to be available to Eastern Utah, and a tentatively planned pipeline from Green River, Wyo. to Southern California will bring natural gas to the central and southeast areas of the state.

Jan 11, 1960

By J. J. Friel, E. S. Erickson

Dolomite-fluxed pellets of various compositions were made from magnetite concentrate, hematite concentrate and a concentrate containing a natural mixture of both. Physical properties and reduction test results were used to ascertain proper compositions and firing temperatures. These pellets were subjected to physical tests and to reduction tests. Petrographic and electron microprobe examinations were made to evaluate the effect of composition and fining on the phase assemblage. We interpreted our test results in terms of chemistry and microstructure and related these to properties. This approach enabled w to determine the composition best suited to each of the three concentrates. Compared with acid pellets, dolomite- fluxed pellets of the optimum compositions had similar physical properties but swelled less, softened at a higher temperature, and reduced faster and more completely.

Jan 1, 1983

By N. R. MacMillan

INTRODUCTION The Bullmoose Coal Project is part of a major development in northeastern British Columbia which comprises a new rail line, a new townsite, powerline, highway, the upgrading of the Canadian National Railway's main line, a new coal port at Prince Rupert and two new coal mines, the Bullmoose mine and the Quintette mine. The total investment by all parties is estimated to be in excess of $2.6 billion and made up approximately as follows : [Table No. 1 $ Millions - Quintette Coal Limited 950 Teck-Bullmoose Coal Inc. 275 Canadian National Railway Company 800 6 British Columbia Railway Company Port at Prince Rupert 280 Townsite, Roads 6- Power ] The new infrastructure is intended to serve not only the Bullmoose and Quintette coal projects but also eventually a number of other coal properties in northeastern British Columbia. The Bullmoose project is structured on a joint venture basis as follows : [Table No. 2 Teck Corporation 51% Lornex Mining Corporation Ltd. 39% Nissho Iwai Coal Development 1 0% (Canada) Ltd. -- 100% ] The mine has a capacity of 2.3 million tonnes of clean coal per year. In the initial years 1.7 million tonnes will be metallurgical coal and 0.6 million tonnes thermal coal. After the first three years of operations the annual production of metallurgical coal will increase to an average of approximately 2.1 million tonnes and the production of thermal coal will decrease to an average of approximately 0.2 million tonnes. At this level of 2.3 million tonnes annual production, the Bullmoose mine has sufficient reserves for at least 26 years of production. History Brameda Resources Ltd. commenced coal exploration in the Bullmoose-Sukunka area in 1969. Teck obtained an option on the Bullmoose coal licences in 1970 and started surface exploration and diamond drilling in 1971. Teck earned a 50% interest in the property, and thereafter expenses were jointly financed by Teck and Brameda. In 1981 Brameda merged with Teck making Teck the sole owner. The initial phase of the exploration program, which was completed in 1975, included 7,200 meters of diamond drilling in 35 holes. During 1976 and 1977, detailed exploration and test work were carried out on the South Fork and West Fork areas where multiple seams close to surfaces indicated the potential for large tonnages of strippable coal. In those two years, work included road construction, detailed mapping and trenching to outline the coal seam traces at the surface, 6,300 meters of diamond drilling in 80 holes, and 300 meters of underground bulk sampling from seven adits. Washability tests and analysis work were carried out on the drill cores and adit samples, and pilot plant washability studies were undertaken. In 1978 and 1979 Teck engineers prepared open pit mining plans and production schedules and Kaiser Engineering was retained to prepare a layout of the plant preparation facility. A feasibility study prepared by Teck's engineering group in January 1982 was the base document used by the Lenders in assessing the technical and economic viability of the project. Property Location The property lies some 650 kilometers northeast of Vancouver, and 87 kilometers south by road from the village of Chetwynd. The Sukunka property (British Petroleum) adjoins to the north, the Mount Spieker property (Ranger Oil Option) adjoins to the east, and the Quintette property is located to the southeast.

Jan 1, 1985

By W. D. France, H. l. Burghoff

FABRICATORS of copper and copper alloys have contended with the problems of reconversion during the past year in endeavoring to return to the full-scale production that is demanded of them. The problems have not been easy, for the industry, like so many others, has had to deal with strikes of long duration, and material shortages, particularly in the raw materials, copper, zinc, lead, and tin. Despite all these obstacles, it was possible to gear production to new peacetime records during the latter part of the year. This was made possible not only by the use of multiple shifts of personnel, but also by the improved production equipment, the development of which had been stimulated by wartime necessity. The work of installing new and better equipment is still continuing, and virtually every company is engaged in improving or planning to improve its processes.

Jan 1, 1947

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

[Secretary's Note.—The following official tables, prepared by the government of the State of Nuevo Leon, and presented to the Institute at the fifth seseion of its Mexican meeting, held at Monterrey, November 26, 1901, present in compact form a general summary of the mineral and metallurgical industry of the State for the preceding calendar year, together with a statement of the railway-shipments of ores from January 1 to October 31, 1901, which, in the absence of direct official mining and metallurgical statistics (not yet available for that year), clearly indicates an increased activity and productiveness of these industries. In other words, the mines are reported to have yielded in 1900 a total product of 83,960,169 kilos of ore; whereas, the railway is reported to have carried, in 10 months of 1901, a total of 108,318,647 kilos of ore. At this rate, the railway-shipments for 1901 mould amount to nearly 130,000,000 kilos. It is, of course, possible that the railwaystatistics include other freight than ores, or that they include duplications, such as would be involved in the record, first of certain ores transported, and afterwards of the " base bullion " produced therefrom. An accurate comparison is therefore impossible ; yet, after making all reasonable allowances for such items as have been named, it seems safe to infer that the mining and metallurgical industry of this State accomplished in 1901 a substantial progress.]

Jan 1, 1902

By Paul Foote

SEEBECK discovered, in 1821, that if, in a closed circuit of two metals the two junctions are at different temperatures, an electric current will flow in the circuit. In the case of an iron and a copper wire, for example, current will flow from copper to iron at the hot junction, or from iron to copper at the cold junction. Two factors combine to cause the current. An electromotive force exists between the two metals, the magnitude of which, depends upon the temperature and upon the metals; this is called the Peltier e.m.f. If a single wire of homogeneous material is heated at one end, an electromotive force is developed between the ends of the wire, the magnitude of which depends upon the metal and upon the difference in temperature; this is known as the Thomson e.m.f: The total e.m.f. acting in the circuit is the sum of the Peltier e.m.f. at the two junctions and the Thomson e.m.f. in each wire, consideration being given, of course, to the algebraic signs of the four e.m.f.'s. The total electromotive force thus depends upon the difference in temperature of the two

Jan 9, 1919

By James E. Lawver

A SURVEY of Minerals Beneficiation Div. membership indicated genuine interest in automatic process control, but revealed that the average mill is operating with a minimum of self-regulating devices. Apparently, the mill operators are content to continue without controls until the practicality of self-regulating devices is more generally accepted, or, in the opinion of the writer, until automatic controls become a necessity to meet economic demands of product quality and cost. Both to stimulate interest in control, and to solicit publication of technical know-how by members and equipment manufacturers, this paper presents a cross section of control problems in two general categories: (a) Control problems that can usually be solved by reference to the literature, i.e. controls that have proven successful in the mineral or chemical industries; (b) Problems that are troublesome and frequently unsolved due to unavoidable adverse conditions in the mill circuit to be controlled.

Jan 10, 1953

By AIME

After an adventurous past-four changes of government in thirty years -the whole of Silesia and attached coal territories have become part of the Polish State. The coal resources of this area are the biggest among the European countries. Under a surface area of 5700 sq km are about 100 coal seams, with a total thickness of 150 meters. According to German estimates, there are some 150 billion metric tons of coal ranging in thickness up to 14 m within a depth of 1500 m. The seams are mostly level, free from faults, with good top and bottom; the coal is of excellent quality, hard and clean; and mining conditions are favorable. The mines are worked at considerable depth by means of vertical shafts and operate with cage and skip hoisting. Before the war, the mines were up to date, equipped with modern machines. Among the European countries, output per man shift was the highest ? 1.9 to 2.1 metric tons ? and cost of production was the lowest.

Jan 1, 1949

By C. C. Whittier

CIVILIZATION'S PROGRESS, which has multiplied man's comforts, conveniences, a n d happiness, is based upon the extensive employment of natural minerals and sources of energy. Mineral resources are basic factors in modern economic development, machine industry, international trade and world power. A survey of mineral consumption shows that the United States leads the world in the production and consumption of energy materials, of metals, and of the large and diverse array of earth materials that fall in the nonmetallic mineral group. The use of nonrnetallic minerals exceeded both the metals and the fuels in the long period before the industrial age, but it is only in the last two decades that consumption of non- metals has kept pace with and approximated in value the output of metals. Although the data of production in the first half of the last century are meager and fragmentary, the record of the past fifty years-the period of most rapid growth-is available, and reveals an astounding growth.

Jan 1, 1933

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

AALL, Christian H.,(M'49), Asst Res Dir Monsanto Chemical Co Anniston, Ala AALSETH, Earl P ,(J,51), Amerada Petr Corp Geological Dept Williston N Dak AAMOT, Olav Crone, (M'29), Met Pacific N W Alloys, Inc , Box 6215, Hillyard P 0 Spokane 14, Wash AARING, Floyd D ,(J'48), Petr Engr P 0 Box 130, Calgary, Alta Canada AARCNSON, Hubert Irving, (S'47), Carnegie Inst of Tech., Pittsburgh, Pa ABADIE, Henry G ,(M'43), Asst to the Sup- of Operations, Long Beach Oil Development Co ,255 So Santa Clara Ave Long Beach, Calif ABBISS, H. J., (A'50), Min. Engr., Buchans Mining Co., Ltd.. Buchans, Newfoundland ABBOTT, Clarence Eugene, (M'04), 901 Insurance Bldg , Raleigh, N C ABBOTT, George, (S'52), Mass Inst of Tech Cambridge, Mass

Jan 1, 1952